Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM U

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch on (IG) and turn the tester ON.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.


f.

Follow the instructions on the tester and read the Data List.

ECM:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NC) Counter gear speed/
Min.: 0 rpm
Max.: 12,750 rpm
4th (O/D) gear when shift lever is on D (after warming up the engine);
Intermediate shaft speed (NC) becomes close to the engine speed
Data is displayed in increments of 50 rpm
SPD (NT) Input turbine speed/
Min.: 0 rpm
Max.: 12,750 rpm
·

Lock-up ON (after warming up engine):

Input turbine speed (NT) is equal to engine speed.

·

Lock-up OFF (idling with shift lever on N):

Input turbine speed (NT) is nearly equal to engine speed.


Data is displayed in increments of 50 rpm
Neutral Position SW Signal PNP switch status/
ON or OFF
Shift lever is:
On P or N: ON
Not on P or N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (see page (Click here))


Stop Light Switch Stop light switch status/
ON or OFF
·

Brake pedal is depressed: ON

·

Brake pedal is released: OFF


-
Shift Status ECM gear shift command/
1st, 2nd, 3rd or 4th
Shift lever position is:
On D: 1st, 2nd, 3rd or 4th
-
Shift SW Status (R Range) PNP switch status/
ON or OFF
Shift lever is:
On R: ON
Not on R: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (see page (Click here))


Shift SW Status (P Range) PNP switch status/
ON or OFF
Shift lever is:
On P: ON
Not on P: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (see page (Click here))


Shift SW Status (N Range) PNP switch status/
ON or OFF
Shift lever is:
On N: ON
Not on N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (see page (Click here))


Shift SW Status (D Range) PNP switch status/
ON or OFF
Shift lever is:
On D: ON
Not on D: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (see page (Click here))


Sports Shift Up SW Sports shift up switch status/
ON or OFF
·

Continuously shift to "+" (up-shift): ON

·

Release "+" (up-shift): OFF


-
Sports Shift Down SW Sports shift down switch status/
ON or OFF
·

Continuously shift to "+" (down-shift): ON

·

Release "+" (down-shift): OFF


-
Sports Mode Selection SW Sports mode select switch status/
ON or OFF
Shift lever position is:
On S, "+" and "-": ON
Not on S, "+" and "-": OFF
-
A/T Oil Temperature 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall test:

Approximately 80°C (176°F)

·

Equal to ambient temperature while engine is cold


If value is -40°C (-40°F) or "150°C (302°F) or more", ATF temperature sensor circuit is open or short circuited
Lock Up Solenoid Status Lock-up solenoid status/
ON or OFF
·

Lock-up: ON

·

Not on lock-up: OFF


-
SLT Solenoid Status Shift solenoid SLT status/
ON or OFF
·

Accelerator pedal is depressed: OFF

·

Accelerator pedal is released: ON


-



PERFORM ACTIVE TEST


HINT:

Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.

The Data List can be displayed during the Active Test.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch on (IG) and turn the tester ON.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


f.

Perform the Active Test.

ECM:
Tester Display Test Part Control Range Diagnostic Note
Activate the Solenoid (SLT)* [Test Details]
Operate shift solenoid SLT and raise line pressure
[Vehicle Condition]
·

Vehicle stopped

·

IDL: ON


HINT:

OFF: Line pressure up (when Active Test's "Activate the solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)

ON: No action (normal operation)


ON / OFF -
Activate the Solenoid (S4) [Test Details]
Operate the shift solenoid S4
[Vehicle Condition]
·

Vehicle stopped

·

Shift lever P or N position


ON / OFF -
Activate the Lock Up [Test Details]
Control shift solenoid DSL to set automatic transaxle to the lock-up condition
[Vehicle Condition]
·

Throttle valve opening angle: 20% or more

·

Vehicle speed: 70 km/h (43 mph) or more

·

Gear: Highest gear


ON / OFF Possible to check shift solenoid valve DSL operation
Control the Shift Position [Test Details]
Operate shift solenoid valve and set each shift lever position manually
[Vehicle Condition]
·

IDL: ON

·

50 km/h (31 mph) or less


[Other information]
·

Press "→" button: Shift up

·

Press "←" button: Shift down


1st / 2nd / 3rd / 4th Possible to check operation of shift solenoid valves
Activate the Solenoid (DSL) [Test Details]
Operate the shift solenoid DSL
[Vehicle Condition]
·

Vehicle stopped

·

Shift lever P or N position


ON / OFF -
Activate the Solenoid (SL1) [Test Details]
Operate the shift solenoid SL1
[Vehicle Condition]
·

Vehicle stopped

·

Shift lever P or N position


ON / OFF -
Activate the Solenoid (SL2) [Test Details]
Operate the shift solenoid SL2
[Vehicle Condition]
·

Vehicle stopped

·

Shift lever P or N position


ON / OFF -

HINT:

*: "Activate the solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transaxle, which is used in the Hydraulic Test (see page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.