Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT LOCK SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292101 SHIFT LOCK SYSTEM G

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LOCK SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK SHIFT LOCK OPERATION

a.

Move the shift lever to P.


b.

Turn the engine switch off.


c.

Check that the shift lever cannot be moved to any position other than P.


d.

Turn the engine switch on (IG), depress the brake pedal and check that the shift lever can be moved to other positions.


Hide 33563 2.CHECK SHIFT LOCK RELEASE BUTTON OPERATION

a.

When operating the shift lever with the shift lock release button pressed, check that the lever can be moved to any position other than P. If the operation cannot be performed as specified, check the shift lever assembly.


Hide 3.CHECK KEY INTERLOCK OPERATION

a.

Turn the engine switch on (IG).


b.

Depress the brake pedal and move the shift lever to any position other than P.


c.

Check that the engine switch cannot be turned off.


d.

Move the shift lever to P, turn the engine switch off and check that the key can be removed. If the results are not as specified, inspect the shift lock control unit.


Hide 33560 4.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY

C140200E03
0.51,0.396 0.885,1.01 false 2.688,0.271 1.854,1 false 0.927,1.531 0.448,1.969 false 0.26,0.26 0.583,0.438 0.323,0.177 10 false STP 2.729,0.177 2.896,0.354 0.167,0.177 10 false E 0.281,1.917 0.49,2.094 0.208,0.177 10 false IG

a.

Measure the voltage of the connector.

HINT:

Do not disconnect the shift lock control ECU connector.


Standard voltage:
Tester Connection Condition Specified Condition
6 (ACC) - 1 (E) Engine switch on (IG) 10 to 14 V
6 (ACC) - 1 (E) Engine switch on (ACC) 10 to 14 V
6 (ACC) - 1 (E) Engine switch off Below 1 V
4 (STP) - 1 (E) Depress brake pedal 10 to 14 V
4 (STP) - 1 (E) Release brake pedal Below 1 V
6 (STP) - 3 (E) Depress brake pedal 10 to 14 V
6 (STP) - 3 (E) Release brake pedal Below 1 V
5 (KLS+) - 1 (E) Engine switch on (ACC) and shift lever on P Below 1 V
5 (KLS+) - 1 (E) Engine switch on (ACC) and shift lever not on P 7.5 to 11 V
5 (KLS+) - 1 (E) Engine switch on (ACC) and shift lever not on P (after approx. 1 second) 6 to 9 V
8 (IG) - 1 (E) Engine switch on (IG) 10 to 14 V
8 (IG) - 1 (E) Engine switch on (IG) 10 to 14 V
12 (IG) - 3 (E) Engine switch off Below 1 V
12 (IG) - 3 (E) Engine switch off Below 1 V



b.
C140200E04
2.698,0.313 1.844,1.01 false 2.76,0.198 2.917,0.396 0.156,0.198 10 false E

Measure the resistance of the connector.

HINT:

Do not disconnect the shift lock control ECU connector.


Standard resistance:
Tester Connection Measurement Condition Specified Condition
1 (E) - Body ground Always Below 1 Ω
3 (E) - Body ground Always Below 1 Ω


If the result is not as specified, replace the shift lock control ECU.