Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TORQUE CONVERTER AND DRIVE PLATE
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292106 TORQUE CONVERTER AND DRIVE PLATE G

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER ASSEMBLY

a.
AT00953E09
1.417,0.417 1.958,0.24 1.958,0.24 1.729,0.75 false 1.948,0.063 2.292,0.229 0.344,0.167 10 false SST

Inspect the one-way clutch.

i.

Set SST into the inner race of the one-way clutch.

SST
09350-32014  (09351-32010)


ii.

Install SST so that it fits in the notch of the torque converter hub and the outer race of the one-way clutch.

SST
09350-32014  (09351-32020)


iii.
AT03306E13
1.635,0.135 1.979,0.49 0.344,0.354 10 false Hold 2.385,0.948 2.76,1.302 0.375,0.354 10 false Lock 2.74,1.583 3.073,1.917 0.333,0.333 10 false Free 1.875,1.635 2.198,1.969 0.323,0.333 10 false Turn

Stand the torque converter assembly up and turn the SST.

Standard:

If the one-way clutch is turned clockwise, it rotates freely and if turned counterclockwise, it locks.




b.
D224296E03
0.115,0.104 2.365,0.625 2.25,0.521 10 false Sample showing maximum allowable amount of powder in ATF

Determine the condition of the torque converter assembly.

i.

If the inspection result of the torque converter assembly satisfies the following conditions, replace the torque converter assembly.

Malfunction:

·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch is free or locked in both directions.

·

The amount of powder in the ATF is greater than the sample shown in the illustration (See the sample).


HINT:

The sample shows approximately. 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF taken out from a removed torque converter assembly.




c.

Replace the ATF in the torque converter assembly.

i.

If the ATF is discolored and/or has a foul odor, stir the ATF in the torque converter assembly and drain it.



d.
C011090

Clean and check the oil cooler and oil pipe line.

i.

If the torque converter assembly is inspected or the ATF is replaced, clean the oil cooler and oil pipe line.

·

Apply compressed air of 196 kPa (2 kgf/cm2, 28 psi) into the inlet hose.

·

If a large amount of powder is found in the ATF, add new ATF using a bucket pump and clean the oil cooler and oil pipe line again.



ii.

If the ATF is cloudy, inspect the oil cooler (radiator).



e.
D025368E92
1.729,1.885 2.24,0.833 false 2.281,0.74 3.208,1.458 0.927,0.719 10 false The bottom is damaged. 0.135,0.094 0.917,0.333 0.781,0.24 10 false CORRECT 1.188,0.094 2.073,0.302 0.885,0.208 10 false INCORRECT

Prevent deformation of the torque converter assembly and damage to the oil pump gear.

i.

When there is any damage due to the end of the bolt for the torque converter assembly and to the bottom of the bolt hole, replace the bolt and torque converter assembly.


ii.

All of the bolts should be the same length.


iii.

Bolts with washers must be used.



Hide 2.INSPECT DRIVE PLATE

a.
C194476E08
1.646,1.042 1.792,1.229 0.146,0.188 10 false 1 2.229,1.896 2.375,2.083 0.146,0.188 10 false 2 3.031,1.833 3.177,2.021 0.146,0.188 10 false 3 3.208,1.167 3.323,1.354 0.115,0.188 10 false 4 2.771,0.49 2.917,0.677 0.146,0.188 10 false 5 1.969,0.271 2.115,0.458 0.146,0.188 10 false 6 0.354,1.781 1.677,1.948 1.323,0.167 10 false : Measurement Point

Check the drive plate damage.


b.

Set up a dial indicator and measure the runout of the 6 portions around the torque converter assembly contact surfaces.

Maximum runout:

0.30 mm (0.0118 in.)


If the runout is not within the specification or the drive plate is damaged, replace the drive plate.

If installing a new drive plate, be careful of the orientation of the spacers and tighten the bolts (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION).