Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM U

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  TERMINALS OF ECU  


TCM


U189044E02
3.479,0.073 3.844,0.26 0.365,0.188 12 false D5

HINT:

Each TCM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Symbols (Terminals No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the TCM terminals.


Symbols (Terminals No.) Wiring Color Terminal Description Condition Specified Condition
R (D5-15) - E1 (D5-8) R - BR R shift position switch signal Ignition switch on (IG) and shift lever in R position 10 to 14 V
Ignition switch on (IG) and shift lever in any position except R position Below 1 V
D (D5-16) - E1 (D5-8) L - BR D shift position switch signal Ignition switch on (IG) and shift lever in D or 3 position 10 to 14 V
Ignition switch on (IG) and shift lever in any position except D and 3 position Below 1 V
STP (D5-12) - E1 (D5-8) B - BR Stop light switch signal Brake pedal is depressed 7.5 to 14 V
Brake pedal is released Below 1.5 V
NSW (D5-11) - E1 (D5-8) L-B - BR Park/neutral switch signal Ignition switch on (IG) and shift lever in P or N position Below 2 V
Ignition switch on (IG) and shift lever in any position except P or N position Below 1 V
STA (D5-10) - E1 (D5-8) W - BR Starter signal Cranking (shift lever position in P or N position, Ignition switch START) 10 to 14 V
Ignition switch on (IG) and shift lever in any position except P or N position Below 2 V
SPD1 (D5-3) - E1 (D5-8) V - BR Speed signal from combination meter Vehicle speed 12 mph (20 km/h) Pulse generation
(See waveform 1)
BATT (D5-1) - E1 (D5-8) Y - BR Battery (for measuring battery voltage and for TCM memory) Always 9 to 14 V
IG2 (D5-13) - E1 (D5-8) R - BR Ignition switch Ignition switch on (IG) 9 to 14 V
+B (D5-18) - E1 (D5-8) Y - BR Power source of TCM Ignition switch on (IG) 9 to 14 V
CAN+ (D5-6) - E1 (D5-8) B - BR CAN communication line Ignition switch on (IG) Pulse generation
(See waveform 2)
CAN- (D5-7) - E1 (D5-8) W - BR CAN communication line Ignition switch on (IG) Pulse generation
(See waveform 3)

a.
G034872E10
2.646,0.24 3.198,0.438 0.552,0.198 10 false 5 V/DIV. 2.792,1.229 3.198,1.427 0.406,0.198 10 false GND 1.677,1.708 2.427,1.906 0.75,0.198 10 false 20 ms./DIV.

Waveform 1

Reference:
Terminal SPD1 - E1
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Vehicle speed 12 mph (20 km/h)


b.
G036660E33
2.635,1.396 3.021,1.594 0.385,0.198 10 false GND 2.396,0.323 2.927,0.49 0.531,0.167 10 false 1 V/DIV. 1.458,1.594 2.208,1.76 0.75,0.167 10 false 10 ms./DIV.

Waveform 2

Reference:
Terminal CAN+ - E1
Tool setting 1 V/DIV., 10 ms./DIV.
Vehicle condition Engine is stopped, ignition switch on (IG)


c.
G036661E32
2.365,0.271 3.031,0.469 0.667,0.198 10 false 1 V/DIV. 1.448,1.573 2.427,1.771 0.979,0.198 10 false 10 ms./DIV. 2.604,1.344 2.99,1.542 0.385,0.198 10 false GND

Waveform 3

Reference:
Terminal CAN- - E1
Tool setting 1 V/DIV., 10 ms./DIV.
Vehicle condition Engine is stopped, ignition switch on (IG)



ECM


HINT:

Each ECM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Symbols (Terminals No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration below as a reference for the ECM terminals.


U188256E02
2.708,0.406 2.99,0.563 0.281,0.156 10 false D1 5.396,0.406 5.656,0.563 0.26,0.156 10 false A7

Symbols (Terminals No.) Wiring Color Terminal Description Condition Specified Condition
S (A7-25) - E1 (D1-81) Y - BR S shift position switch signal Ignition switch on (IG) and shift lever in S position 10 to 14 V
Ignition switch on (IG) and shift lever in any position except S position Below 1 V
SFTU (A7-16) - E1 (D1-81) P - BR Up shift switch signal Ignition switch on (IG) and shift lever in S position 10 to 14 V
Ignition switch on (IG) and shift lever in "+" position (Up shift) Below 1 V
SFTD (A7-51) - E1 (D1-81) GR - BR Down shift switch signal Ignition switch on (IG) and shift lever in S position 10 to 14 V
Ignition switch on (IG) and shift lever in "-" position (Down shift) Below 1 V