Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM J

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

When moving the shift lever into the S position using the transmission control switch, it is possible to switch the shift range position between "1" (first range) and "6" (sixth range).

Shifting up "+" once raises one shift range position, and shifting down "-" lowers one shift range position.

WIRING DIAGRAM

C157363E02
0.323,1.031 1.135,1.448 0.813,0.417 10 false From RH-IG Relay 1 1.583,1.271 2.396,1.448 0.813,0.177 10 false RH ECU-IG 2.76,2.313 4.521,2.5 1.76,0.188 10 false Transmission Control Switch 2.75,4.26 3.073,4.438 0.323,0.177 10 false TCM 2.615,0.896 2.771,1.073 0.156,0.177 10 false 6 3.573,0.896 3.802,1.073 0.229,0.177 10 false 13 3.615,1.323 3.771,1.5 0.156,0.177 10 false 4 3.615,1.729 3.771,1.906 0.156,0.177 10 false 5 2.573,1.719 2.781,1.896 0.208,0.177 10 false 11 3.5,2.906 3.656,3.083 0.156,0.177 10 false 7 3.5,3.313 3.656,3.49 0.156,0.177 10 false 6 2.979,3.104 3.333,3.281 0.354,0.177 10 false CAN- 2.969,3.5 3.365,3.677 0.396,0.177 10 false CAN+ 5.656,0.406 5.979,0.583 0.323,0.177 10 false ECM 3.469,3.104 3.74,3.281 0.271,0.177 10 false D5 3.469,3.5 3.74,3.677 0.271,0.177 10 false D5 4.896,1.021 5.156,1.198 0.26,0.177 10 false A7 4.896,1.427 5.156,1.604 0.26,0.177 10 false A7 4.896,3.115 5.167,3.292 0.271,0.177 10 false D1 4.906,3.5 5.177,3.677 0.271,0.177 10 false D1 4.896,1.833 5.156,2.01 0.26,0.177 10 false A7 5.208,1.01 5.365,1.188 0.156,0.177 10 false S 5.208,1.417 5.583,1.594 0.375,0.177 10 false SFTD 5.208,1.823 5.583,2 0.375,0.177 10 false SFTU 5.198,3.115 5.552,3.292 0.354,0.177 10 false CAN- 5.198,3.5 5.594,3.677 0.396,0.177 10 false CAN+ 4.906,0.823 5.073,1 0.167,0.177 10 false 25 4.896,1.24 5.063,1.417 0.167,0.177 10 false 51 4.885,1.635 5.052,1.813 0.167,0.177 10 false 16 4.927,2.917 5.083,3.094 0.156,0.177 10 false 1 4.938,3.313 5.094,3.49 0.156,0.177 10 false 2 2.75,2.135 3,2.323 0.25,0.188 10 false G9

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
U189454E02
0.115,0.073 1.635,0.51 1.521,0.438 10 false Wire Harness Side: (Connector Front View) 0.677,1.219 0.969,1.396 0.292,0.177 10 false G9

Disconnect the transmission control switch connector of the shift lock control unit assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
G9-6 - Body ground Ignition switch on (IG) 10 to 14 V
Ignition switch off Below 1 V




OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.
U189454E02
0.115,0.073 1.635,0.51 1.521,0.438 10 false Wire Harness Side: (Connector Front View) 0.677,1.219 0.969,1.396 0.292,0.177 10 false G9

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
G9-11 - Body ground Below 1 Ω




OK

3.INSPECT TRANSMISSION CONTROL SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION CONTROL SWITCH
a.
U189452E02
0.135,0.073 1.552,0.625 1.417,0.552 10 false Switch Side: (Connector Front View) 1.573,1.219 1.885,1.396 0.313,0.177 10 false G9

Measure the resistance between each terminal of the shift lock control unit assembly when the shift lever is moved to each position.

Standard resistance:
Tester Connection Shift Position Specified Condition
G9-6 - G9-13 S, "+" and "-" Below 1 Ω
Except S, "+" and "-" 10 kΩ or higher
G9-5 - G9-11 Press continuously
"+"
(Up shift)
Below 1 Ω
S 10 kΩ or higher
G9-4 - G9-11 Press continuously
"-"
(Down shift)
Below 1 Ω
S 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION CONTROL SWITCH

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
G100098E42
1.865,0.99 2,0.396 true 2.031,0.906 2.75,0.438 true 1.469,1.375 0.427,1.677 0.427,1.677 0.427,1.823 true 0.073,0.052 1.417,0.26 1.344,0.208 10 false Wire Harness Side: 0.26,1.844 0.729,2.031 0.469,0.188 10 false SFTD 2.792,0.354 3.26,0.542 0.469,0.188 10 false SFTU 1.948,0.219 2.177,0.406 0.229,0.188 10 false S 0.969,1.708 2.813,1.896 1.844,0.188 10 false ECM Connector (Front view)

Connect the transmission control switch connector of the shift lock control unit assembly.


b.

Disconnect the ECM connector.


c.

Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard voltage:
Tester Connection Shift Position Specified Condition
A7-25 (S) - Body ground S, "+" and "-" 10 to 14 V
Except S, "+" and "-" Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard resistance:
Tester Connection Shift Position Tester Connection Specified Condition
A7-16 (SFTU) - Body ground Press continuously
"+"
(Up shift)
A7-16 (SFTU) - Body ground Below 1 Ω
S 10 kΩ or higher
A7-51 (SFTD) - Body ground Press continuously
"-"
(Down shift)
A7-51 (SFTD) - Body ground Below 1 Ω
S 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR