Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0710  Transmission Fluid Temperature Sensor "A" Circuit  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value for use by the TCM.

G102505E01
1.729,2.146 2,1.76 false 0.271,0.521 1.323,0.813 1.052,0.292 10 false Resistance 2.052,1.625 3.26,1.938 1.208,0.313 10 false Acceptable range 0.99,3.948 2.042,4.24 1.052,0.292 10 false Temperature

The TCM applies a voltage to the temperature sensor through terminal OIL of the TCM.

The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.

The TCM calculates the fluid temperature based on the voltage signal.

DTC No. DTC Detection Condition Trouble Area
P0710 (a) and (b) are detected momentarily (within 0.5 sec.) when neither P0712 nor P0713 is detected (1-trip detection logic).
(a) ATF temperature sensor resistance is less than 79 Ω.
(b) ATF temperature sensor resistance is more than 156 kΩ.
HINT:

Within 0.5 sec., the malfunction switches from (a) to (b) or from (b) to (a).


·

Open or short in ATF temperature sensor circuit

·

Transmission wire (ATF temperature sensor)

·

TCM


P0712 ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic).
·

Short in ATF temperature sensor circuit

·

Transmission wire (ATF temperature sensor)

·

TCM


P0713 ATF temperature sensor resistance is more than 156 kΩ when 15 minutes or more have elapsed after the engine starts.
DTC is detected for 0.5 sec. or more (1-trip detection logic).
·

Open in ATF temperature sensor circuit

·

Transmission wire (ATF temperature sensor)

·

TCM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the automatic transmission fluid (ATF) temperature sensor (TFT sensor) circuit. The automatic transmission fluid (ATF) temperature sensor converts ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and the TCM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the TCM interprets this as a fault in the ATF sensor or wiring. The TCM will turn on the MIL and store the DTC.

HINT:

The ATF temperature can be checked on the intelligent tester display.

*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.


WIRING DIAGRAM

C133262E17
5.635,0.531 6.042,0.854 0.406,0.323 10 false TCM 2.26,3.854 3.563,4.25 1.302,0.396 10 false Transaxle Assembly 5.073,1.802 5.615,1.969 0.542,0.167 10 false THO1 5.083,2.927 5.625,3.094 0.542,0.167 10 false E2 1.01,3.323 2.656,3.688 1.646,0.365 10 false ATF Temperature Sensor 4.813,1.688 5.031,1.854 0.219,0.167 10 false 18 4.802,2.813 5.021,2.979 0.219,0.167 10 false 17

CAUTION / NOTICE / HINT

DATA LIST


HINT:

According to the Data List displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the Data List as the first step in troubleshooting is one method to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch on (IG).


e.

Turn on the tester.


f.

Enter the following items: "Powertrain / ECT / Data List".


g.

According to the display on the tester, read "Data List".

Tester Display Measurement Item/Range Normal Condition
A/T Oil Temperature 1 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
·

After Stall Test;

Approx. 80°C (176°F)

·

Equal to ambient temperature when cold soak



HINT:
·

When DTC P0712 is output and the intelligent tester indicates 150°C (302°F) or more, there is a short circuit.


·

When DTC P0713 is output and the intelligent tester indicates -40°C (-40°F), there is an open circuit.


·

Measure the resistance between terminal OIL and body ground.



Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit

HINT:
·

If the circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.


·

It is not necessary to inspect the circuit when P0711 is set.





PROCEDURE

1.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)
a.
C133212E94
1.896,1.042 2.26,0.74 false 2.052,1.115 2.271,1.26 false 2.281,0.656 2.677,0.802 0.396,0.146 10 false THO1 2.302,1.198 2.5,1.344 0.198,0.146 10 false E2

Remove the TCM from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
17 (E2) - 18 (THO1) 90 Ω to 156 kΩ
17 (E2) - Body ground 10 kΩ or higher
18 (THO1) - Body ground 10 kΩ or higher


HINT:

If the resistance is out of the specified range with the ATF temperature shown in the table below, the driveability of the vehicle may decrease.


Standard resistance:
ATF Temperature Specified Condition
10°C (50°F) 5.8 to 7.1 kΩ
110°C (230°F) 0.22 to 0.28 kΩ




NG

2.INSPECT ATF TEMPERATURE SENSOR

OK

REPLACE TCM

2.INSPECT ATF TEMPERATURE SENSOR
a.
C133224E01
1.47,2.028 1.867,2.187 0.396,0.159 10 THO1 2.3,2.028 2.541,2.180 0.241,0.152 10 E2 1.9,1.139 1.579,2.003 false 2.024,1.144 2.384,1.994 false

Disconnect the ATF temperature sensor connector from the transmission wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
E2 - THO1 90 Ω to 156 kΩ
E2 - Body ground 10 kΩ or higher
THO1 - Body ground 10 kΩ or higher


HINT:

If the resistance is out of the specified range with the ATF temperature shown in the table below, the driveability of the vehicle may decrease.


Standard resistance:
ATF Temperature Specified Condition
10°C (50°F) 5.8 to 7.1 kΩ
110°C (230°F) 0.22 to 0.28 kΩ




OK

REPLACE TRANSMISSION WIRE

NG

REPLACE ATF TEMPERATURE SENSOR ASSEMBLY