Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The amount of current flow to the solenoid is controlled by the (*) duty ratio of the TCM output signal. The higher the duty ratio becomes, the higher the lock-up hydraulic pressure becomes during the lock-up operation.

C133227E02
0.927,0.594 1.198,0.771 0.271,0.177 10 false ON 0.906,1.49 1.229,1.667 0.323,0.177 10 false OFF 1.583,0.448 1.781,0.594 0.198,0.146 10 false A 2.083,1.323 2.281,1.469 0.198,0.146 10 false B 1.74,2.063 2.292,2.25 0.552,0.188 10 false 1 Cycle 3.75,0.385 4.417,0.729 0.667,0.344 10 false Hydraulic Pressure 5.323,2.146 5.896,2.333 0.573,0.188 10 false Current

(*) Duty Ratio

The duty ratio is the ratio of the period of continuity in one cycle. For example, if A is the period of continuity in one cycle, and B is the period of non-continuity, then Duty Ratio = A/(A + B) x 100 (%).

DTC No. DTC Detection Condition Trouble Area
P2759 Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLU circuit

·

Shift solenoid valve SLU

·

TCM



MONITOR DESCRIPTION

When an open or short in the shift solenoid valve (SLU) circuit is detected, the TCM determines there is a malfunction. The TCM will turn on the MIL and store this DTC.

WIRING DIAGRAM

C133261E72
5.635,0.51 6,0.844 0.365,0.333 10 false TCM 2.073,3.854 3.448,4.281 1.375,0.427 10 false Transaxle Assembly 5.073,1.813 5.615,1.979 0.542,0.167 10 false SLU+ 5.823,1.073 6.365,1.24 0.542,0.167 10 false +B 5.083,3.188 5.625,3.354 0.542,0.167 10 false SLU- 1.594,2.354 3.646,2.74 2.052,0.385 10 false Shift Solenoid Valve SLU 4.813,1.552 4.979,1.729 0.167,0.177 10 false 11 4.865,2.938 5.021,3.115 0.156,0.177 10 false 5 1.417,2 1.573,2.177 0.156,0.177 10 false 2 1.406,2.677 1.563,2.854 0.156,0.177 10 false 1

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SLU)
a.
C133212E07
2.375,0.32 2.734,0.469 0.359,0.149 10 SLU- 2.32,1.223 2.690,1.372 0.370,0.149 10 SLU+ 2.066,0.765 2.34,0.428 false 2.06,0.944 2.348,1.219 false

Remove the TCM from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
11 (SLU+) - 5 (SLU-) 5.0 to 5.6 Ω
(at 20°C (68°F))



c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Check for short:
Tester Connection Specified Condition
11 (SLU+) - Body ground 10 kΩ or higher
5 (SLU-) - Body ground 10 kΩ or higher




NG

2.INSPECT SHIFT SOLENOID VALVE SLU

OK

REPLACE TCM

2.INSPECT SHIFT SOLENOID VALVE SLU
a.
G102540E04
1.76,3.115 2.469,2.76 false 1.49,3.115 0.781,2.802 false 0.771,1.24 1.479,0.885 false 2.49,1.219 1.781,0.906 false 0.115,0.063 1.938,0.385 1.823,0.323 10 false Shift Solenoid Valve SLU: 0.646,1.177 0.958,1.375 0.313,0.198 10 false 1 2.552,1.167 2.865,1.365 0.313,0.198 10 false 2 1.198,4.167 1.51,4.365 0.313,0.198 10 false (-) 1.917,4.177 2.229,4.375 0.313,0.198 10 false (+) 0.635,2.698 0.948,2.896 0.313,0.198 10 false 1 2.531,2.656 2.844,2.854 0.313,0.198 10 false 2

Remove the shift solenoid valve SLU.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
1 - 2 5.0 to 5.6 Ω
(at 20°C (68°F))



c.

Connect a positive (+) lead through a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

OK:

The solenoid makes an operating sound.




OK

REPLACE TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID VALVE SLU