Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensors detect the wheel speed and send the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the TCM via the combination meter. The TCM determines the vehicle speed based on the frequency of these pulse signals.

A079413E74
0.271,1.208 1.115,1.583 0.844,0.375 10 false From Speed Sensor 1.583,0.99 2.385,1.323 0.802,0.333 10 false Skid Control ECU 2.719,0.521 3.302,0.719 0.583,0.198 10 false 4-Pulse 4.667,0.521 5.25,0.719 0.583,0.198 10 false 4-Pulse 3.479,1.417 4.469,1.615 0.99,0.198 8 false Combination Meter 5.771,1.26 6.156,1.458 0.385,0.198 10 false TCM

DTC No. DTC Detection Condition Trouble Area
P0500 When the ECT sensor is normal and the counter gear speed is 300 rpm or more, the vehicle speed signal is not input for 2 seconds or more.
·

Vehicle speed sensor

·

Vehicle speed sensor signal circuit

·

Combination meter

·

TCM



MONITOR DESCRIPTION

The TCM assumes that the vehicle is being driven when the transmission counter gear indicates more than 300 rpm and over 30 seconds have passed since the park/neutral position switch was turned off. If there is no signal from the vehicle speed sensor with these conditions satisfied, the TCM concludes that the vehicle speed sensor is malfunctioning. The TCM will turn on the MIL and a DTC will be set.

WIRING DIAGRAM

A122761E24
5.552,0.396 5.885,0.573 0.333,0.177 10 false TCM 5.052,1.302 5.438,1.479 0.385,0.177 10 false SPD1 4.76,2.51 5.01,2.688 0.25,0.177 10 false D5 4.802,1.219 4.906,1.396 0.104,0.177 10 false 3 5.083,2.5 5.281,2.677 0.198,0.177 10 false E1 4.771,1.417 5.01,1.594 0.24,0.177 10 false D5 4.813,2.302 4.906,2.479 0.094,0.177 10 false 8 1.958,1.531 2.188,1.708 0.229,0.177 10 false 40 1.688,1.302 1.896,1.448 0.208,0.146 10 false +S 0.833,0.427 1.198,0.583 0.365,0.156 10 false G28 0.833,0.604 2.042,0.76 1.208,0.156 10 false Combination Meter

PROCEDURE

1.INSPECT SPEEDOMETER (METER OPERATION)
a.

Drive the vehicle and check if operation of the speedometer in the combination meter is normal.

HINT:

The vehicle speed sensor is operating normally if the speedometer display is normal.




OK

2.INSPECT TCM

NG

CHECK SPEEDOMETER CIRCUIT

2.INSPECT TCM
a.
U189042E02
1.031,1.323 0.771,1.948 true 1.76,1.271 1.979,1.938 true 0.052,0.052 1.354,0.229 1.302,0.177 10 false Wire Harness Side: 0.833,0.313 2.646,0.49 1.813,0.177 10 false TCM Connector (Front View) 0.281,0.594 0.552,0.74 0.271,0.146 10 false D5 0.677,1.958 0.875,2.104 0.198,0.146 10 false E1 1.854,1.958 2.26,2.104 0.406,0.146 10 false SPD1

Shift the lever to the neutral position.


b.

Jack up the vehicle.


c.

Disconnect the TCM connector.


d.

Turn the ignition switch on (IG).


e.
A062954E10
0.219,0.573 0.656,0.938 0.438,0.365 10 false 4.5 to 5.5 V 0.323,1.583 0.594,1.781 0.271,0.198 10 false 0 V 2.448,1.719 3.375,1.917 0.927,0.198 10 false Turn the wheel

Measure the voltage according to the value(s) in the table below as the wheel is turned slowly.

OK:
Tester Connection Specified Condition
D5-3 (SPD1) - D5-8 (E1) Voltage is generated intermittently


HINT:

The output voltage should fluctuate up and down similarly to the diagram when the wheel is turned slowly.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR