Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the TCM even when the ignition switch is off. This power allows the TCM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, these memories are cleared and the TCM determines that there is a malfunction in the power supply circuit. When the engine is next started, the TCM will illuminate the MIL and set the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in TCM back-up power source circuit.
DTC is detected for 3 sec. or more (1-trip detection logic).
·

Open in TCM back-up power source circuit

·

TCM



HINT:

If DTC P0560 is set, the TCM does not store other DTCs.


WIRING DIAGRAM

C157358E02
6.146,0.646 6.573,0.823 0.427,0.177 10 false TCM 5.563,1.448 5.802,1.625 0.24,0.177 10 false D5 5.563,2.76 5.802,2.938 0.24,0.177 10 false D5 3.719,1.625 4.146,1.802 0.427,0.177 10 false EFI 1.979,1.604 2.708,1.781 0.729,0.177 10 false F/B BATT 1.156,2.5 1.885,2.677 0.729,0.177 10 false FL MAIN 5.854,1.302 6.281,1.479 0.427,0.177 10 false BATT 5.865,2.75 6.177,2.927 0.313,0.177 10 false E1 5.604,1.229 5.75,1.406 0.146,0.177 10 false 1 5.604,2.542 5.75,2.719 0.146,0.177 10 false 8 1.271,3.76 1.823,3.938 0.552,0.177 10 false Battery

PROCEDURE

1.INSPECT TERMINAL VOLTAGE (BATT VOLTAGE OF TCM)
a.
U189033E02
1.479,1.281 1.292,1.948 true 0.052,0.042 1.25,0.24 1.198,0.198 10 false Wire Harness Side: 0.833,0.323 2.615,0.521 1.781,0.198 10 false TCM Connector (Front View) 0.198,0.781 0.469,0.927 0.271,0.146 10 false D5 1.135,1.958 1.51,2.104 0.375,0.146 10 false BATT

Disconnect the TCM connector.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Specified Condition
BATT (D5-1) - Body ground 10 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI FUSE - TCM)

2.CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND)
a.
U189034E02
1.031,1.323 0.802,1.948 true 0.052,0.042 1.302,0.24 1.25,0.198 10 false Wire Harness Side: 0.833,0.313 2.635,0.49 1.802,0.177 10 false TCM Connector (Front View) 0.198,0.781 0.469,0.927 0.271,0.146 10 false D5 0.708,1.958 0.927,2.104 0.219,0.146 10 false E1

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
E1 (D5-8) - Body ground Below 1 Ω




OK

REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR