Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM D

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  MONITOR DRIVE PATTERN  


MONITOR DRIVE PATTERN FOR ECT TEST


a.

Perform this drive pattern as one method to simulate the detection conditions of the ECT malfunctions. (The DTCs may not be detected due to differences from the actual driving conditions. Some codes may not be detected using this drive pattern.)

HINT:

Preparation for driving

·

Warm up the engine sufficiently. (Engine coolant temperature should be 60°C (140°F) or higher.)

·

Drive the vehicle when the atmospheric temperature is -10°C (14°F) or higher. (Malfunctions may not be detected when the atmospheric temperature is less than -10°C (14°F).)


When driving

·

Drive the vehicle through all gears.

Starting with the vehicle at a stop, accelerate and observe the following shift and operation: 1st to 2nd to 3rd to 4th to 5th to 6th to 6th (lock-up ON).

·

Confirm engine braking using the S position.

While driving in the 6 (S) position and 6th gear lock-up, shift to the "-" position to down-shift from 6th to 5th, 5th to 4th, 4th to 3rd, 3rd to 2nd, and 2nd to 1st.

Check that proper engine braking occurs whenever a down-shift takes place.

·

Repeat the above driving pattern three times or more.



NOTICE:
·

The monitor status can be checked using the intelligent tester. When using the intelligent tester, monitor status can be found in "Powertrain / ECT / Data List".

·

In the event that the drive pattern must be interrupted (possibly due to traffic conditions or other factors), the drive pattern can be resumed and, in most cases, the monitor can be completed.

·

Perform this drive pattern on a road with the fewest hills possible and strictly observe the posted speed limits and traffic laws while driving.



G102506E02
0.552,0.094 1.615,0.354 1.063,0.26 10 false Vehicle Speed 1.167,0.427 7.156,0.708 5.99,0.281 10 false Maintain a constant speed or gradual acceleration (with the throttle open) for 3 minutes or more.*1 0.396,0.906 0.896,1.521 0.5,0.615 10 false Approx. 62 mph 0.417,1.896 0.927,2.573 0.51,0.677 10 false Approx. 50 mph 0.865,3.177 1.646,3.51 0.781,0.333 10 false 0 0.396,3.531 1.135,3.969 0.74,0.438 10 false Warmed up sufficiently 1.469,3.792 3.615,4.344 2.146,0.552 10 false Normal acceleration through all the gears from 1st to 6th 3.563,3.396 4.458,3.729 0.896,0.333 10 false Stop (Idling) 5.115,0.99 6.073,1.385 0.958,0.396 10 false Lock-up ON Vehicle Speed 0.396,1.24 1.052,1.927 0.656,0.688 10 false (100 km/h) 0.417,2.229 1.031,2.938 0.615,0.708 10 false (80 km/h)

HINT:

*1: Drive the vehicle at a sufficient speed in the uppermost gear, to allow lock-up to engage. The vehicle can be driven at a speed lower than that in the above diagram under the lock-up condition.


NOTICE:

It is necessary to drive the vehicle for approximately 30 minutes to detect DTC P0711 (ATF temperature sensor malfunction).