Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM M

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  REGISTRATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When the automatic transaxle is replaced, the transaxle's compensation code must be input into the TCM (Proceed to step 1). After the automatic transaxle is reinstalled, the QR code label will be positioned where the code cannot be read. Therefore, before reinstalling the automatic transaxle, record the transaxle compensation codes or input them in the intelligent tester.

·

When the TCM is replaced, the existing transaxle compensation codes must be input into the new TCM (Proceed to step 2).



PROCEDURE

Hide 1.INPUT TRANSAXLE COMPENSATION CODE INTO TCM

NOTICE:

Transaxle compensation codes are unique, 60-digit alphanumeric values printed on the QR label. If an incorrect transaxle compensation code is input into the TCM, shift shock may occur.


a.
C133268E02
2.222,2.382 3.209,2.538 0.987,0.157 10 QR Code Label 2.398,1.279 3.259,1.777 0.861,0.499 10 Transaxle Compensation Code 1.053,0.246 2.040,0.403 0.987,0.157 10 QR Code Label 2.183,2.453 2.023,2.453 2.023,2.453 2.168,2.883 false

Record the transaxle compensation code specified on the QR label.

HINT:

The transaxle compensation code is imprinted on the QR label.



b.

Shift the shift lever to the N or P position.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch on (IG).


e.

Turn the tester on.

NOTICE:

Do not start the engine.



f.
C122773

Enter the menu items in this order: Powertrain / ECT / Utility / A/T Code Registration.


g.

Press "Next".


h.
C122774

Press "Next" again to proceed.


i.
C122776

Select "Set Compensation Code".


j.

Press "Next".


k.
C122777

Register the compensation code.

i.

Press "Input".


ii.
A096465

Manually input the transaxle compensation code. The code is a 60-digit alphanumeric value printed on the QR label. After inputting the code, press "OK".



l.
C122778

Check that the compensation code displayed on the screen is correct by comparing it with the 60-digit alphanumeric value on the QR label.

NOTICE:

If an incorrect transaxle compensation code is input into the TCM, shift shock will occur.



m.

Press "Next" to set the compensation code to the TCM.

C366242


n.

Press "Exit".


Hide 2.TRANSFER TRANSAXLE COMPENSATION CODE

NOTICE:

Transaxle compensation codes are 60-digit alphanumeric values printed on the QR label. If an incorrect transaxle compensation code is input into the TCM, shift shock may occur.


HINT:

The following operation is available for use with TCMs that can transmit the registered transaxle compensation code to the intelligent tester.


a.

Shift the shift lever to the N or P position.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch on (IG).


d.

Turn the tester on.

NOTICE:

Do not start the engine.


HINT:

The transaxle compensation code is imprinted on the QR label.



e.

Read the transaxle compensation code.

i.
C122773

Enter the menu items in this order: Powertrain / ECT / Utility / A/T Code Registration.


ii.

Press "Next".


iii.
C122774

Press "Next" again to proceed.


iv.
C122799

Select "Read Compensation Code".


v.

Press "Next".


vi.
C122801

Press "Save".


vii.
C122789

C122790

Press "Save" or "Overwrite".

HINT:

Press "Overwrite".


NOTICE:

Do not use the code specified on the transaxle QR label even if the transaxle compensation code cannot be read using the intelligent tester. The code printed on an in-service transaxle may not match its current characteristics. Replace the TCM with a new one and perform a road test to allow the TCM to learn.



viii.
C122792

Press "Exit".


ix.

Turn the ignition switch off.



f.

Replace the TCM.


g.

Set the transaxle compensation code.

i.

Turn the ignition switch on (IG).


ii.

Turn the tester on.


iii.
C122773

Enter the menu items in this order: Powertrain / ECT / Utility / A/T Code Registration.


iv.

Press "Next".


v.
C122774

Press "Next" again to proceed.


vi.
C122776

Select "Set Compensation Code".


vii.

Press "Next".


viii.
C122777

Press "Open".


ix.
C122779

Press "Open" again to proceed.


x.
C122803

Press "Exit".