Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0872  Transmission Fluid Pressure Sensor / Switch "C" Circuit Low  P0873  Transmission Fluid Pressure Sensor / Switch "C" Circuit High  


DESCRIPTION

ATF pressure switch No. 1 is installed in the shift solenoid valve ATF output passage. This switch is used to identify the malfunctioning part when a fail-safe operation is performed. If the shift solenoid valve malfunctions when the ATF switch has a malfunction, a fail-safe operation will be performed. This fail-safe operation is different from the fail-safe operation performed when the solenoid valve malfunctions and the ATF switch is normal.

DTC No. DTC Detection Condition Trouble Area
P0872 ATF pressure switch No. 1 OFF is detected twice when any of the gears from 1st to 4th engages normally.
·

ATF temperature sensor assembly (ATF pressure switch No. 1)


·

Transmission wire


·

TCM


P0873 ATF pressure switch No. 1 ON is detected twice when 5th or 6th gear engages normally.

WIRING DIAGRAM

C133258E39
5.073,1.906 5.615,2.073 0.542,0.167 10 false TPS1 5.625,0.542 5.99,0.865 0.365,0.323 10 false TCM 0.938,3.177 2.99,3.594 2.052,0.417 10 false ATF Pressure Switch No. 1 2,3.865 4.052,4.292 2.052,0.427 10 false Transaxle Assembly 4.792,1.771 4.958,1.948 0.167,0.177 10 false 10 2.104,1.792 2.26,1.969 0.156,0.177 10 false 3 1.635,1.792 2.021,1.958 0.385,0.167 10 false TPS1

PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0872 OR P0873)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the intelligent tester on.


c.

Enter the following items: "Powertrain / ECT / DTC / Current or Pending".


d.

Read the DTCs using the intelligent tester.

Result:
Display (DTC output) Proceed to
Only "P0873" is output A
Only "P0872" is output B
"P0872 or P0873" and other DTCs are output C


HINT:

If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.




A

2.CHECK TRANSMISSION WIRE (SHORT TO GROUND)

B

4.CHECK TRANSMISSION WIRE

C

GO TO DTC CHART

2.CHECK TRANSMISSION WIRE (SHORT TO GROUND)
a.
C133212E10
2.286,1.287 2.665,1.442 0.379,0.156 10 TPS1 1.395,0.783 2.245,1.322 false

Remove the TCM.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Condition Specified Condition
10 (TPS1) - Body ground (Valve body assembly) 10 kΩ or higher




NG

3.CHECK ATF TEMPERATURE SENSOR ASSEMBLY (ATF PRESSURE SWITCH NO. 1)

OK

REPLACE TCM

3.CHECK ATF TEMPERATURE SENSOR ASSEMBLY (ATF PRESSURE SWITCH NO. 1)
a.
C142707E01
1.781,1.144 2.476,2.036 false 2.276,2.045 2.666,2.198 0.390,0.152 10 TPS1

Disconnect the connector from the ATF temperature sensor assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Condition Specified Condition
3 (TPS1) - Body ground (Valve body assembly) 10 kΩ or higher




OK

REPLACE TRANSMISSION WIRE

NG

REPLACE ATF TEMPERATURE SENSOR ASSEMBLY

4.CHECK TRANSMISSION WIRE
a.
C133269E11
1.521,1.365 1.177,2.198 false 1.792,3.75 1.594,4.167 false 1.146,0.385 2.479,0.552 1.333,0.167 10 false TCM Side Connector 1.083,2.667 2.573,2.854 1.49,0.188 10 false Sensor Side Connector 1.01,2.219 1.385,2.365 0.375,0.146 10 false TPS1 1.365,4.177 1.74,4.323 0.375,0.146 10 false TPS1

Remove the TCM.


b.

Disconnect the speed sensor connector from the transmission wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Condition Specified Condition
10 (TPS1) - 3 (TPS1) Below 1 Ω
10 (TPS1) or 3 (TPS1) - Body ground (Valve body assembly) 10 kΩ or higher




OK

REPLACE ATF TEMPERATURE SENSOR ASSEMBLY

NG

REPLACE TRANSMISSION WIRE