Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0877  Transmission Fluid Pressure Sensor / Switch "D" Circuit Low  P0878  Transmission Fluid Pressure Sensor / Switch "D" Circuit High  


DESCRIPTION

ATF pressure switch No. 2 is installed in the shift solenoid valve ATF output passage. This switch is used to identify the malfunctioning part when a fail-safe operation is performed. If the shift solenoid valve malfunctions when the ATF switch has a malfunction, a fail-safe operation will be performed. This fail-safe operation is different from the fail-safe operation performed when the solenoid valve malfunctions and the ATF switch is normal.

DTC No. DTC Detection Condition Trouble Area
P0877 ATF pressure switch No. 2 OFF is detected twice when any of the gears from 4th to 6th engages normally.
·

ATF temperature sensor assembly (ATF pressure switch No. 2)


·

Transmission wire


·

TCM


P0878 ATF pressure switch No. 2 ON is detected twice when any of the gears from 1st to 3rd engages normally.

WIRING DIAGRAM

C133258E40
5.094,1.896 5.635,2.063 0.542,0.167 10 false TPS2 5.615,0.594 5.979,0.823 0.365,0.229 10 false TCM 0.958,3.188 3.01,3.406 2.052,0.219 10 false ATF Pressure Switch No. 2 2.063,3.865 4.115,4.292 2.052,0.427 10 false Transaxle Assembly 4.802,1.771 4.969,1.948 0.167,0.177 10 false 20 2.104,1.781 2.26,1.958 0.156,0.177 10 false 4 1.646,1.792 2.073,1.958 0.427,0.167 10 false TPS2

PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0877 OR P0878)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the intelligent tester on.


c.

Enter the following items: "Powertrain / ECT / DTC / Current or Pending".


d.

Read the DTCs using the intelligent tester.

Result:
Display (DTC output) Proceed to
Only "P0878" is output A
Only "P0877" is output B
"P0877 or P0878" and other DTCs are output C


HINT:

If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.




A

2.CHECK TRANSMISSION WIRE (SHORT TO GROUND)

B

4.CHECK TRANSMISSION WIRE

C

GO TO DTC CHART

2.CHECK TRANSMISSION WIRE (SHORT TO GROUND)
a.
C133212E11
2.272,0.339 2.651,0.495 0.379,0.156 10 TPS2 1.663,1.056 2.272,0.435 false

Remove the TCM.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Condition Specified Condition
20 (TPS2) - Body ground (Valve body assembly) 10 kΩ or higher




NG

3.CHECK ATF TEMPERATURE SENSOR ASSEMBLY (ATF PRESSURE SWITCH NO. 2)

OK

REPLACE TCM

3.CHECK ATF TEMPERATURE SENSOR ASSEMBLY (ATF PRESSURE SWITCH NO. 2)
a.
C142708E01
2.216,2.018 2.586,2.172 0.369,0.154 10 TPS2 1.664,1.138 2.216,2.018 false

Disconnect the connector from the ATF temperature sensor assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Condition Specified Condition
4 (TPS2) - Body ground (Valve body assembly) 10 kΩ or higher




OK

REPLACE TRANSMISSION WIRE

NG

REPLACE ATF TEMPERATURE SENSOR ASSEMBLY

4.CHECK TRANSMISSION WIRE
a.
C133269E12
1.615,3.75 1.708,4.104 false 1.802,1.719 1.573,2.229 false 1.198,0.438 2.531,0.604 1.333,0.167 10 false TCM Side Connector 1.073,2.677 2.563,2.865 1.49,0.188 10 false Sensor Side Connector 1.406,2.24 1.781,2.385 0.375,0.146 10 false TPS2 1.573,4.135 1.948,4.281 0.375,0.146 10 false TPS2

Remove the TCM.


b.

Disconnect the speed sensor connector from the transmission wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Condition Specified Condition
20 (TPS2) - 4 (TPS2) Below 1 Ω
20 (TPS2) or 4 (TPS2) - Body ground (Valve body assembly) 10 kΩ or higher




OK

REPLACE ATF TEMPERATURE SENSOR ASSEMBLY

NG

REPLACE TRANSMISSION WIRE