Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TORQUE CONVERTER CLUTCH AND DRIVE PLATE › from 2016.05
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292122 TORQUE CONVERTER CLUTCH AND DRIVE PLATE G

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER CLUTCH AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER ASSEMBLY

a.

Inspect the one-way clutch.

i.
C151051E19
1.125,0.135 1.625,0.438 0.5,0.302 10 true Smooth 0.698,0.688 1.083,0.99 0.385,0.302 10 true Heavy

Press on the spline of the stator with a finger and rotate it. Check that it rotates smoothly when turned clockwise and rotates heavily when turned counterclockwise.

If necessary, clean the torque converter assembly and recheck the one-way clutch.

Replace the torque converter assembly if the one-way clutch still fails the inspection.



b.
D224296E04
0.146,0.094 2.313,0.656 2.167,0.563 10 false Sample showing maximum amount of powder in ATF

Determine the condition of the torque converter assembly.

i.

If the inspection result of the torque converter assembly satisfies the following conditions, replace the torque converter assembly.

Malfunction item :


·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to the N position.

·

The one-way clutch is free or locked in both directions.

·

The amount of powder in the ATF is greater than the sample shown in the illustration (see the sample).


HINT:

The sample shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF that is taken out from the removed torque converter assembly.




c.

Replace the ATF in the torque converter assembly.

i.

If the ATF is discolored and/or has foul odor, stir the ATF in the torque converter assembly and drain it.



d.
D025368E92
1.729,1.885 2.24,0.833 false 2.281,0.74 3.208,1.458 0.927,0.719 10 false The bottom is damaged. 0.135,0.094 0.917,0.333 0.781,0.24 10 false CORRECT 1.188,0.094 2.073,0.302 0.885,0.208 10 false INCORRECT

Prevent deformation of the torque converter assembly and damage to the oil pump gear.

i.

When there is any damage due to the end of the bolt for the torque converter assembly and to the bottom of the bolt hole, replace the bolt and the torque converter assembly.


ii.

All of the bolts should be the same length.


iii.

Bolts with washers must be used.



Hide 2.INSPECT DRIVE PLATE

a.

Check the drive plate damage.

If the runout is not within the specification or the drive plate is damaged, replace the drive plate.

If installing a new drive plate, be careful of the orientation of the spacers and tighten the bolts (See page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION).


b.
C190458E03
1.723,0.296 1.824,0.461 0.101,0.166 10 1 1.279,1.044 1.518,1.210 0.238,0.166 10 2 1.85,1.927 2.088,2.093 0.238,0.166 10 3 2.64,1.867 2.740,2.032 0.100,0.166 10 4 2.862,1.227 3.101,1.393 0.238,0.166 10 5 2.44,0.517 2.678,0.682 0.238,0.166 10 6 0.445,1.781 1.602,1.930 1.157,0.149 10 : Measuring Point

Set up a dial indicator and measure the runout of the 6 portions around the torque converter assembly contact surfaces.

Maximum runout:

0.30 mm (0.0118 in.)