Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT › 2013.04–2014.09
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292124 AUTOMATIC TRANSAXLE UNIT G

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 35394 1.INSPECT TRANSMISSION OIL CLEANER MAGNET

a.
C138722

Use the removed magnets to collect any steel chips. Examine the chips and particles in the pan and on the magnets to determine what type of wear has occurred in the transaxle:

Result:
Steel (magnetic):

Bearing, gear and plate wear

Brass (non-magnetic):

Bearing wear



Hide 35701 2.INSPECT INPUT SHAFT SUB-ASSEMBLY

a.
C136696

Using a dial indicator, measure the input shaft end play.

End play:

0.012 to 1.250 mm (0.0005 to 0.0492 in.)



Hide 3.INSPECT NO. 2 CLUTCH DISC

a.
C138267

Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

NOTICE:

If the linings of the discs are peeled off or discolored, or if part of the groove is damaged, replace all discs.



Hide 35706V 4.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C138259

Using a dial indicator, measure the inside diameter of the bushings of the planetary sun gear.

Standard inside diameter:

25.525 to 25.546 mm (1.0049 to 1.0057 in.)


Maximum inside diameter:

25.546 mm (1.0057 in.)


If the inside diameter is greater than the maximum, replace the planetary sun gear.


Hide 5.INSPECT NO. 1 CLUTCH DISC

a.
C138265

Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

NOTICE:

If the linings of the discs are peeled off or discolored, or if part of the groove is damaged, replace all discs.



Hide 35683B 6.INSPECT NO. 3 BRAKE DISC

a.
C138255

Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

NOTICE:

If the linings of the discs are peeled off or discolored, or if part of the groove is damaged, replace all discs.



Hide 34330 7.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C138260

Using a feeler gauge, measure the clearance between the underdrive planetary gear and the pinion gear at 4 points.

Standard clearance:

0.18 to 0.54 mm (0.0071 to 0.0213 in.)


If the clearance is greater than the standard clearance, replace the underdrive planetary gear.


Hide 35730 8.INSPECT REAR PLANETARY SUN GEAR ASSEMBLY

a.
C138266

Using a dial indicator, measure the inside diameter of the bushing of the rear planetary sun gear sub-assembly.

Standard inside diameter:

25.580 to 25.601 mm (1.0071 to 1.0079 in.)


Maximum inside diameter:

25.601 mm (1.0079 in.)


If the inside diameter is greater than the maximum, replace the rear planetary sun gear assembly.


Hide 35683B 9.INSPECT NO. 1 BRAKE DISC

a.
C138255

Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

NOTICE:

If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.



Hide 35608L 10.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C138254

Using a vernier caliper, measure the free length of the 3 2nd brake piston return springs including the spring seats.

Standard free length:

23.85 mm (0.9390 in.)


If the free length is shorter than the standard free length, replace the 2nd brake piston return spring.


Hide 35790 11.INSPECT ONE-WAY CLUTCH ASSEMBLY

a.
C138723

Temporarily install the one-way clutch assembly to the planetary ring gear.


b.

Rotate the one-way clutch assembly clockwise followed by anticlockwise. The clutch assembly should only rotate in one direction.

If the one-way clutch assembly does not operate normally, replace it.


Hide 35720 12.INSPECT PLANETARY GEAR ASSEMBLY

a.
C137433E06
1.521,0.354 1.667,0.521 0.146,0.167 10 false A 2.073,3.427 2.219,3.594 0.146,0.167 10 false B

Using a feeler gauge, measure the clearance between the planetary gear case and each pinion gear at points A and B.

- Standard Clearance
A point 0.23 to 0.59 mm (0.0091 to 0.0232 in.)
B point 0.16 to 0.66 mm (0.0063 to 0.0260 in.)

If the clearance is greater than the standard clearance, replace the planetary gear assembly.


Hide 35682A 13.INSPECT NO. 2 BRAKE DISC

a.
C137438

Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

NOTICE:

If the linings of the discs are peeled off or discolored, or if part of the groove is damaged, replace all discs.



Hide 35068C 14.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C141533

a.

Using a vernier caliper, measure the free length of the 1st and reverse brake return spring together with the spring seat.

Standard free length:

15.79 mm (0.6217 in.)


If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring.


Hide 35682A 15.INSPECT CLEARANCE OF NO. 2 BRAKE

a.
C137439

Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard clearance:

0.884 to 1.196 mm (0.0348 to 0.0471 in.)


HINT:

Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.

HINT:

There are 5 flanges of different thicknesses.


No. 2 brake flange thickness: mm (in.)
Thickness Thickness
4.0 (0.157) 4.3 (0.169)
4.1 (0.161) 4.4 (0.173)
4.2 (0.165) -


Hide 35691A 16.INSPECT CLEARANCE OF NO. 1 BRAKE

a.
C138258

Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard clearance:

0.807 to 0.974 mm (0.0318 to 0.0383 in.)


HINT:

Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.

HINT:

There are 6 flanges of different thicknesses.


No. 1 brake flange thickness: mm (in.)
Thickness Thickness
3.0 (0.118) 3.3 (0.130)
3.1 (0.122) 3.4 (0.134)
3.2 (0.126) 3.5 (0.138)


Hide 35683B 17.INSPECT CLEARANCE OF NO. 3 BRAKE

a.
C138724E14
2.292,3.729 1.771,3.021 false 2.198,0.208 2,0.865 false 3.042,3.698 3.198,3.698 3.198,3.698 3.125,3.938 false 0.865,0.219 1.75,0.406 0.885,0.188 10 false Dimension A 2.292,2.813 3.094,2.979 0.802,0.167 10 false Dimension B 1.01,2.885 1.781,3.031 0.771,0.146 10 false No. 3 Brake 2.24,0.042 3.219,0.396 0.979,0.354 10 false Front Oil Pump Assembly 1.875,3.958 3.375,4.26 1.5,0.302 8 false Contact Surface of Front Oil Pump Assembly

Using a vernier caliper and a straight edge, measure the distance shown in the illustration (Dimension A) while a load of 500 N (51 kgf, 112 lbf) is being applied to the flange.

HINT:

Measure dimension A at 3 points where the flange diameter is approximately 166 mm (6.54 in.) and calculate the average.



b.

Using a vernier caliper and a straight edge, measure the distance shown in the illustration. (Dimension B).

HINT:

Measure dimension B at 3 points where the No. 3 brake diameter is approximately 166 mm (6.54 in.) and calculate the average.



c.

Calculate the clearance value using the following formula:

Clearance = Dimension B - Dimension A

Standard clearance:

0.599 to 0.761 mm (0.0236 to 0.0300 in.)


If the clearance is not as specified, select an appropriate brake flange so that the clearance will be within the specified range.

HINT:

There are 6 flanges of different thicknesses.


No. 3 brake flange thickness: mm (in.)
Thickness Thickness
3.80 (0.150) 4.10 (0.161)
3.90 (0.154) 4.20 (0.165)
4.00 (0.157) 4.30 (0.169)


Hide 18.INSPECT CLEARANCE OF NO. 1 CLUTCH DISC

a.
C138728

Install the direct multiple disc clutch assembly onto the transaxle rear cover.


b.

Using a dial indicator, measure the No. 1 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

HINT:

Measure the clearance at 3 points where the flange diameter is approximately 152 mm (5.98 in.) and calculate the average.


Pack clearance:

0.806 to 0.974 mm (0.0317 to 0.0383 in.)


If the pack clearance is not as specified, inspect the discs, plates and flange.

HINT:

There are 6 flanges of different thicknesses.


No. 1 clutch flange thickness: mm (in.)
Thickness Thickness
3.0 (0.118) 3.3 (0.130)
3.1 (0.122) 3.4 (0.134)
3.2 (0.126) 3.5 (0.138)


Hide 19.INSPECT CLEARANCE OF NO. 2 CLUTCH DISC

a.
C138727

Install the direct multiple disc clutch assembly onto the transaxle rear cover.


b.

Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

HINT:

Measure the clearance at 3 points where the diameter of the No. 2 direct multiple clutch piston is approximately 152 mm (5.98 in.) and calculate the average.


Pack clearance:

0.544 to 0.744 mm (0.0214 to 0.0293 in.)


If the pack clearance is not as specified, inspect the discs, plates and flange.

HINT:

There are 6 flanges of different thicknesses.


No. 2 clutch flange thickness: mm (in.)
Thickness Thickness
3.0 (0.118) 3.3 (0.130)
3.1 (0.122) 3.4 (0.134)
3.2 (0.126) 3.5 (0.138)