Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT › from 2014.09
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292124 AUTOMATIC TRANSAXLE UNIT A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 35104V 1.REMOVE BREATHER PLUG HOSE

a.
C190663

Using a screwdriver, remove the breather plug hose from the transaxle case sub-assembly.


b.
C190664E04
2.469,1.573 2.75,1.573 false 1.208,0.479 1.646,0.479 false 1.958,1.688 1.427,1.688 false 2.792,1.49 3.063,1.667 0.271,0.177 10 false *3 1.656,0.396 1.865,0.573 0.208,0.177 10 false *1 1.24,1.594 1.448,1.802 0.208,0.208 10 false *2

Using a screwdriver, remove the No. 2 breather plug (ATM) from the breather plug hose.

Text in Illustration
*1 Breather Plug Hose
*2 No. 2 Breather Plug (ATM)
*3 O-ring


c.

Using a screwdriver, remove the O-ring from the No. 2 breather plug (ATM).


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136685

Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.


b.
C136686

Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.

NOTICE:

Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the park/ neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



Hide 3.REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)

a.
C162436

Loosen the nut while holding the oil cooler tube union (inlet oil cooler union).


b.

Remove the oil cooler tube union (inlet oil cooler union) from the transaxle case sub-assembly.


c.

Remove the O-ring from the oil cooler tube union (inlet oil cooler union).


Hide 32921C 4.REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)

a.
C162437

Loosen the nut while holding the oil cooler tube union (outlet oil cooler union).


b.

Remove the oil cooler tube union (outlet oil cooler union) from the transaxle case sub-assembly.


c.

Remove the O-ring from the oil cooler tube union (outlet oil cooler union).


Hide 35104Q 5.REMOVE NO. 1 TRANSAXLE CASE PLUG

a.
C162438

Remove the 3 No. 1 transaxle case plugs from the transaxle case sub-assembly.


b.

Using a screwdriver, remove the 3 O-rings from the 3 No. 1 transaxle case plugs.


Hide 35104R 6.REMOVE NO. 2 TRANSAXLE CASE PLUG

a.
C134959

Using a 6 mm hexagon socket wrench, remove the 3 No. 2 transaxle case plugs from the transaxle housing.


b.

Remove the gasket from each of the 3 No. 2 transaxle case plugs.


Hide 30500 7.SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY

a.
C297754

Support the automatic transaxle assembly with wooden blocks.


Hide 35106D 8.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C297755

Using a 6 mm hexagon socket wrench, remove the overflow plug from the automatic transaxle oil pan sub-assembly.


b.

Remove the gasket from the overflow plug.


c.
C297756

Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.


d.
C297757

Remove the 18 bolts, automatic transaxle oil pan sub-assembly and automatic transaxle oil pan gasket from the automatic transaxle assembly.


e.
C134963E07
2.743,0.137 2.914,0.302 0.172,0.165 10 *1 2.681,0.215 1.884,0.215 1.884,0.215 1.884,1.446 false 2.45,0.996 2.45,0.215 false

Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.

Text in Illustration
*1 Transmission Oil Cleaner Magnet


Hide 35330 10.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C136687

Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.


b.
C136688E10
1.823,0.406 2.063,0.406 false 2.104,0.323 2.583,0.5 0.479,0.177 10 false *1

Remove the O-ring from the valve body oil strainer assembly.

Text in Illustration
*1 O-ring


Hide 35410 11.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C136689

Remove the 11 bolts and transmission valve body assembly from transaxle case sub-assembly.

NOTICE:

When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.



Hide 35145C 12.REMOVE TRANSAXLE CASE GASKET

a.
C287964

Remove the 2 transaxle case gaskets from the transaxle case sub-assembly.


Hide 35102 14.REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C162439

Remove the refill plug from the rear transaxle cover sub-assembly.


b.

Remove the gasket from the refill plug.


c.
C288350

Remove the 3 No. 1 automatic transaxle case plugs from the rear transaxle cover sub-assembly.


d.

Using a screwdriver, remove the 3 O-rings from the 3 No. 1 automatic transaxle case plugs.


e.
U189476

Remove the 14 bolts from the rear transaxle cover sub-assembly.


f.

Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case sub-assembly.


g.
C287966

Using a screwdriver, remove the 3 O-rings from the transaxle case sub-assembly.

HINT:

Tape the screwdriver tip before use.



h.
C297890E10
0.794,0.698 0.999,0.891 0.205,0.193 10 *1 0.405,1.033 0.610,1.226 0.205,0.193 10 *2 1.098,1.292 1.098,0.783 1.098,0.783 0.994,0.783 false 0.726,1.52 0.726,1.115 0.726,1.115 0.622,1.115 false

Remove the thrust needle roller bearing and thrust needle roller race from the rear transaxle cover sub-assembly.

Text in Illustration
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


i.
C299131E11
1.406,0.573 1.49,0.573 1.49,0.573 1.719,0.833 false 1.823,1.823 1.917,1.823 1.917,1.823 1.917,1.292 false 1.25,0.5 1.458,0.677 0.208,0.177 10 false *1 1.656,1.74 1.865,1.917 0.208,0.177 10 false *1

Using a screwdriver, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.

Text in Illustration
*1 Oil Seal Ring


j.
C287967

Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.


k.
C194888E14
1.417,0.885 1.521,0.885 false 1.125,0.823 1.396,1.094 0.271,0.271 10 true SST 3.083,0.823 3.25,1 0.167,0.177 10 false *a 0.354,0.833 0.521,1.01 0.167,0.177 10 false *b

Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.

Text in Illustration
*a Turn
*b Hold

SST
09319-60020  


Hide 35635C 15.REMOVE DIRECT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C136442E02
0.771,2.105 0.942,2.271 0.170,0.167 10 *1 0.873,1.283 0.873,2.062 false 2.568,0.094 2.731,0.260 0.163,0.167 10 *2 2.778,0.162 3.067,0.162 3.067,0.162 2.594,1.413 false

Remove the direct multiple disc clutch assembly from the transaxle case sub-assembly.

Text in Illustration
*1 Direct Multiple Disc Clutch Assembly
*2 Thrust Needle Roller Bearing


b.

Remove the thrust needle roller bearing from the direct multiple disc clutch assembly.


c.
C296565E02
1.396,0.177 1.656,0.177 false 1.417,2 1.646,2 false 1.26,1.927 1.573,2.125 0.313,0.198 10 false *1 1.229,0.094 1.542,0.292 0.313,0.198 10 false *2

Using a screwdriver, remove the intermediate shaft oil seal from the direct multiple disc clutch assembly.

Text in Illustration
*1 Intermediate Shaft Oil Seal
*2 O-ring

HINT:

Tape the screwdriver tip before use.



d.

Using a screwdriver, remove the O-ring from the direct multiple disc clutch assembly.

HINT:

Tape the screwdriver tip before use.



Hide 35635E 16.REMOVE DIRECT MULTIPLE DISC CLUTCH SNAP RING

a.
C136433

Using a screwdriver, remove the direct multiple disc clutch snap ring from the direct multiple disc clutch assembly.


b.
C136434

Remove the No. 2 direct clutch piston from the direct multiple disc clutch assembly.


Hide 17.REMOVE NO. 2 CLUTCH DISC

a.
C359883E01
1.198,1.323 1.198,0.521 1.198,0.521 1.344,0.521 false 1.021,0.927 1.344,0.927 false 1.198,1.323 1.354,1.323 false 2.115,0.708 2.26,0.708 2.26,0.708 2.26,1.5 false 2.115,1.094 2.438,1.094 false 2.104,1.5 2.26,1.5 false 2.073,1.792 2.292,1.792 false 0.844,0.833 1.156,1.031 0.313,0.198 10 false *1 2.469,1.021 2.781,1.219 0.313,0.198 10 false *2 2.333,1.719 2.646,1.917 0.313,0.198 10 false *3

Remove the No. 2 clutch flange, 3 No. 2 clutch discs and 3 No. 2 clutch plates from the direct multiple disc clutch assembly.

Text in Illustration
*1 No. 2 Clutch Plate
*2 No. 2 Clutch Disc
*3 No. 2 Clutch Flange


Hide 35730 19.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

a.
C136436

Using a snap ring expander, remove the snap ring from the direct multiple disc clutch assembly.


b.
C136437

Remove the rear planetary sun gear assembly from the direct multiple disc clutch assembly.


c.
C141542E04
1.281,0.844 0.854,0.583 false 1.271,1.458 0.865,1.594 false 0.667,0.49 0.844,0.656 0.177,0.167 10 false *1 0.667,1.531 0.844,1.719 0.177,0.188 10 false *2

Remove the thrust needle roller bearing and thrust needle roller race from the direct multiple disc clutch assembly.

Text in Illustration
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Hide 21.REMOVE NO. 1 CLUTCH DISC

a.
C136445

Using 2 screwdrivers, remove the 2 snap rings from the direct multiple disc clutch assembly.


b.
U189177E01
2.308,0.233 2.460,0.430 0.151,0.197 10 *1 2.435,1.305 2.597,1.502 0.162,0.197 10 *3 0.884,1.119 1.056,1.323 0.172,0.204 10 *2 1.358,1.201 1.11,1.201 false 2.127,0.987 2.286,0.987 false 2.129,1.376 2.384,1.376 false 2.105,0.314 2.263,0.314 false 1.341,1.552 1.193,1.552 false

Remove the No. 1 clutch flange, 4 No. 1 clutch discs and 4 No. 1 clutch plates from the direct multiple disc clutch assembly.

Text in Illustration
*1 No. 1 Clutch Flange
*2 No. 1 Clutch Plate
*3 No. 1 Clutch Disc


Hide 35111C 23.REMOVE TRANSAXLE HOUSING

a.
C287968

Remove the 20 bolts from the transaxle housing.


b.

Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case sub-assembly.


Hide 24.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE

a.
C194889E04
1.193,1.543 1.512,1.712 0.319,0.169 10 SST 0.942,1.629 1.152,1.629 false

Using SST, remove the counter driven gear front tapered roller bearing outer race and shim from the transaxle housing.

SST
09308-00010  


Hide 35882A 25.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C287969

Remove the bolt, clamp and differential gear lube apply tube from the transaxle housing.


Hide 35035 26.REMOVE FRONT OIL PUMP ASSEMBLY

a.
C287970E02
2.354,0.188 2.719,0.188 false 2.75,0.115 2.979,0.281 0.229,0.167 10 false *1

Remove the 7 bolts and front oil pump assembly from the transaxle case sub-assembly.


b.

Remove the gasket from the front oil pump assembly.

Text in Illustration
*1 Gasket


c.
C293908E07
0.131,2.628 0.304,2.796 0.173,0.168 10 *1 0.629,2.709 0.324,2.709 false

Remove the thrust needle roller race from the underdrive planetary gear assembly.

Text in Illustration
*1 Thrust Needle Roller Race


d.
C294585E10
1.177,0.865 0.885,0.865 false 2.156,2.51 2.406,2.51 false 0.719,0.792 0.969,1.156 0.25,0.365 10 false *1 2.438,2.438 2.917,2.729 0.479,0.292 10 false *2

Remove the thrust needle roller bearing from the counter drive gear nut.

Text in Illustration
*1 Thrust Needle Roller Bearing
*2 O-ring


e.

Remove the O-ring from the transaxle case sub-assembly.


Hide 35301B 27.REMOVE FRONT OIL PUMP BODY O-RING

a.
C293910

Remove the front oil pump body O-ring from the front oil pump body assembly.


Hide 35683B 28.REMOVE NO. 3 BRAKE DISC

a.
C136451E08
1.276,0.625 1.111,0.373 1.111,0.373 0.81,0.373 false 0.574,0.297 0.744,0.453 0.170,0.156 10 *1

Using a screwdriver, remove the snap ring from the front oil pump assembly.

Text in Illustration
*1 Snap Ring


b.
C359885E01
1.156,1.031 1.313,1.031 false 1.229,1.031 1.229,1.49 1.229,1.49 1.313,1.49 false 2.125,0.792 2.208,0.792 2.208,0.792 2.208,1.698 false 2.125,1.26 2.281,1.26 false 2.135,0.417 2.292,0.417 false 1.167,2.063 1.323,2.063 false 2.115,1.698 2.208,1.698 false 2.333,0.354 2.646,0.552 0.313,0.198 10 false *1 2.333,1.177 2.646,1.375 0.313,0.198 10 false *3 0.979,1.979 1.292,2.177 0.313,0.198 10 false *1 0.969,0.948 1.281,1.146 0.313,0.198 10 false *2

Remove the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates from the front oil pump assembly.

Text in Illustration
*1 No. 3 Brake Flange
*2 No. 3 Brake Plate
*3 No. 3 Brake Disc


Hide 34330 30.REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C136458

Remove the underdrive planetary gear assembly from the front oil pump assembly.


Hide 35663 31.REMOVE NO. 3 BRAKE HUB

a.
C136454

Remove the No. 3 brake hub from the underdrive planetary gear assembly.


b.
C202906E12
1.198,0.156 1.323,0.156 1.323,0.156 1.521,0.292 false 1.219,1.167 1.302,1.167 1.302,1.167 1.5,1 false 1.021,0.083 1.198,0.25 0.177,0.167 10 false *1 1.052,1.094 1.229,1.469 0.177,0.375 10 false *2

Remove the thrust needle roller bearing and thrust needle roller race from the underdrive planetary gear assembly.

Text in Illustration
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing


Hide 35706V 32.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C290582E06
0.94,0.376 1.110,0.537 0.170,0.161 10 *1 1.109,0.463 1.404,0.463 false 0.429,1.949 0.599,2.109 0.170,0.161 10 *2 0.598,2.035 0.893,2.035 false 0.971,2.974 1.141,3.134 0.170,0.161 10 *3 1.14,3.06 1.435,3.06 false

While expanding the snap ring with snap ring pliers, remove the planetary sun gear sub-assembly from the underdrive planetary gear assembly.

Text in Illustration
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


b.

Remove the snap ring from the underdrive planetary gear assembly.


Hide 35701 35.REMOVE INPUT SHAFT SUB-ASSEMBLY

a.
C136459

Remove the input shaft sub-assembly from the front oil pump assembly.


b.
C136460E09
2.229,0.617 2.436,0.801 0.207,0.184 10 *2 0.958,0.112 1.160,0.313 0.201,0.202 10 *1 2.451,2.426 2.685,2.613 0.234,0.188 10 *3 1.43,0.21 1.192,0.21 false 2.182,0.709 1.928,0.709 false 1.834,2.726 2.419,2.54 2.419,2.54 1.845,3.055 false 1.845,2.893 2.419,2.54 false 0.984,1.839 1.515,1.839 false 0.777,1.748 0.987,1.921 0.210,0.173 10 *4

Remove the thrust needle roller bearing and thrust needle roller race from the input shaft sub-assembly.

Text in Illustration
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft Oil Seal Ring
*4 Input Shaft Sub-assembly


c.

Using a screwdriver, remove the 3 input shaft oil seal rings from the input shaft sub-assembly.

HINT:

Tape the screwdriver tip before use.



Hide 34321 36.REMOVE UNDERDRIVE PLANETARY SUN GEAR

a.
C136461E04
1.01,0.615 1.385,0.615 false 2.302,1.26 2.01,1.26 false 2.333,1.198 2.5,1.365 0.167,0.167 10 false *2 0.854,0.531 1.01,0.677 0.156,0.146 10 false *1

Remove the underdrive planetary sun gear from the front oil pump assembly.

Text in Illustration
*1 Underdrive Planetary Sun Gear
*2 Thrust Needle Roller Bearing


b.

Remove the thrust needle roller bearing from the front oil pump assembly.


Hide 37.REMOVE NO. 1 BRAKE DISC

a.
C153477E03
2.514,0.492 2.677,0.645 0.163,0.154 10 *1 2.198,0.578 2.489,0.578 false 2.2,1.164 2.331,1.164 2.331,1.164 2.331,0.578 false 0.862,0.802 1.029,0.956 0.167,0.154 10 *2 1.256,0.888 1.062,0.888 false

Using a screwdriver, remove the 2 snap rings and brake snap ring stopper from the front oil pump assembly.

Text in Illustration
*1 Snap Ring
*2 Brake Snap Ring Stopper


b.
U189178E01
3.164,1.263 3.333,1.402 0.170,0.139 10 *3 1.561,1.123 1.732,1.297 0.172,0.174 10 *2 1.561,0.562 1.732,0.736 0.172,0.174 10 *1 1.774,0.652 2.016,0.652 false 1.76,1.211 2.055,1.211 false 1.922,1.211 1.922,2.526 1.922,2.526 2.028,2.526 false 2.043,1.646 1.922,1.646 false 2.055,2.113 1.922,2.113 false 2.993,1.855 2.87,1.855 false 2.87,1.34 3.131,1.34 false

Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the front oil pump assembly.

Text in Illustration
*1 No. 1 Brake Flange
*2 No. 1 Brake Plate
*3 No. 1 Brake Disc


Hide 35608L 39.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C136464

Remove the 3 2nd brake piston return spring sub-assemblies from the front oil pump assembly.


Hide 35608L 40.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621F 41.REMOVE NO. 1 BRAKE PISTON

a.
C136465

While holding the front oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the front oil pump assembly to remove the No. 1 brake piston.


b.
C136466E07
1.979,0.667 2.375,0.667 false 1.365,0.667 0.917,0.667 false 2.406,0.583 2.552,0.74 0.146,0.156 10 false *1 0.708,0.573 0.865,0.729 0.156,0.156 10 false *1

Using a screwdriver, remove the 2 O-rings from the No. 1 brake piston.

Text in Illustration
*1 O-ring

HINT:

Tape the screwdriver tip before use.



Hide 41311 42.REMOVE FRONT DIFFERENTIAL CASE

a.
C136467

Remove the front differential case from the transaxle case sub-assembly.


Hide 35782H 43.REMOVE COUNTER DRIVE GEAR NUT

a.
C136698E06
1.573,0.708 1.188,0.448 true 0.906,0.344 1.24,0.521 0.333,0.177 10 false SST

Using SST and a hammer, release the staked part of the planetary gear assembly.

SST
09930-00010  


b.
C299132E05
1.521,4.052 1.688,4.25 0.167,0.198 10 false P

Turn the manual valve lever shaft sub-assembly 2 notches counterclockwise to set it to the P position as shown in the illustration.


c.
C136468E05
1.604,1.417 0.688,0.292 true 0.406,0.198 0.729,0.365 0.323,0.167 10 false SST

Using SST, remove the counter drive gear nut from the front planetary gear assembly.

SST
09387-00130  


Hide 35783R 44.REMOVE COUNTER DRIVEN GEAR

a.
C299133E01
1.539,3.96 1.705,4.137 0.166,0.177 10 N

Turn the manual valve lever shaft sub-assembly 2 notches clockwise to set it to the N position as shown in the illustration.


b.
C136469

Remove the counter driven gear from the transaxle case sub-assembly.


Hide 45.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING

a.
C194890E02
1.769,0.372 1.939,0.561 0.170,0.188 10 *a 0.206,0.702 0.376,0.890 0.170,0.188 10 *b 1.611,0.66 1.919,0.827 0.308,0.167 10 SST 1.44,0.592 1.587,0.739 1.587,0.739 1.438,1.214 false 1.587,0.739 1.063,1.174 false 2.903,0.114 3.211,0.281 0.308,0.167 10 SST 2.233,0.493 2.883,0.221 2.883,0.221 2.778,0.673 false

Using SST, remove the counter driven gear front tapered roller bearing from the counter driven gear.

Text in Illustration
*a Turn
*b Hold

SST
09950-00020  
09950-00030  
09950-60010  (09951-00400)


Hide 41311F 46.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING

a.
C194891E09
2.25,1.292 2.031,1.604 true 2.885,0.385 2.813,0.385 2.813,0.385 2.688,1.104 true 0.594,0.729 0.25,1.552 0.25,1.552 0.885,1.354 true 1.615,0.479 1.781,0.656 0.167,0.177 10 false *a 0.073,0.583 0.281,0.771 0.208,0.188 10 false *b 0.052,1.594 0.375,1.76 0.323,0.167 10 false SST 2.917,0.313 3.24,0.479 0.323,0.167 10 false SST 1.885,1.625 2.208,1.792 0.323,0.167 10 false SST

Using SST, remove the counter driven gear rear tapered roller bearing from the counter driven gear.

Text in Illustration
*a Turn
*b Hold

SST
09950-40011  (09951-04010, 09952-04010, 09954-04010, 09953-04020, 09955-04071, 09957-04010, 09958-04011)
09950-60010  (09951-00320)


Hide 35558 47.REMOVE PAWL SHAFT CLAMP

a.
C136472

Remove the bolt and pawl shaft clamp from the transaxle case sub-assembly.


Hide 35596 48.REMOVE PAWL STOPPER PLATE

a.
C136473

Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.


Hide 35598 49.REMOVE PARKING LOCK SLEEVE

a.
C136474

Remove the parking lock sleeve from the transaxle case sub-assembly.


Hide 35557 50.REMOVE PARKING LOCK PAWL

a.
C136475E13
1.542,0.24 1.385,0.24 1.385,0.24 1.156,1.302 true 0.948,0.271 0.76,0.271 0.76,0.271 0.521,1.615 true 0.458,2.802 0.458,2.625 0.458,2.625 1.052,2.458 true 1.563,2.677 1.76,3.167 true 0.396,2.833 0.573,3.01 0.177,0.177 10 false *3 1.75,3.188 1.917,3.354 0.167,0.167 10 false *4 0.969,0.198 1.135,0.365 0.167,0.167 10 false *1 1.594,0.177 1.771,0.323 0.177,0.146 10 true *2

Remove the spring, parking lock pawl pin, parking lock pawl shaft and parking lock pawl from the transaxle case sub-assembly.

Text in Illustration
*1 Parking Lock Pawl Shaft
*2 Parking Lock Pawl
*3 Spring
*4 Parking Lock Pawl Pin


Hide 51.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE

a.
C194892E04
0.243,0.499 0.565,0.662 0.322,0.163 10 SST 0.613,0.584 0.842,0.584 false

Using SST, remove the counter driven gear rear tapered roller bearing outer race from the transaxle case sub-assembly.

SST
09308-00010  


Hide 35790 52.REMOVE ONE-WAY CLUTCH ASSEMBLY

a.
C141525

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C141526E10
1.771,1.01 2.313,1.01 false 0.833,0.313 1.281,0.313 false 2.344,0.938 2.51,1.094 0.167,0.156 10 false *2 0.677,0.24 0.865,0.448 0.188,0.208 10 false *1

Remove the one-way clutch assembly with planetary ring gear from the transaxle case sub-assembly.

Text in Illustration
*1 One-way Clutch Assembly with Planetary Ring Gear
*2 Thrust Needle Roller Bearing


c.

Remove the thrust needle roller bearing from the front planetary gear assembly.


Hide 35743K 54.REMOVE PLANETARY RING GEAR

a.
C201345E07
0.813,0.146 0.906,0.146 0.906,0.146 1.26,0.427 false 1.115,1.417 1.396,1.417 false 2.521,0.979 2.802,1.052 2.802,1.052 2.802,1.135 false 0.635,0.063 0.792,0.25 0.156,0.188 10 false *1 0.958,1.333 1.125,1.51 0.167,0.177 10 false *3 2.729,1.146 2.917,1.344 0.188,0.198 10 false *2

Remove the planetary ring gear from the one-way clutch assembly.

Text in Illustration
*1 One-way Clutch Assembly
*2 Outer Race Retainer
*3 Planetary Ring Gear


b.

Remove the outer race retainer from the one-way clutch assembly.


Hide 35762E 55.REMOVE PLANETARY RING GEAR FLANGE

a.
C136480E09
1.271,0.646 0.969,0.646 false 0.958,2.302 1.219,2.302 false 2.052,1.302 2.365,1.302 false 0.792,2.219 0.969,2.385 0.177,0.167 10 false *3 2.406,1.229 2.573,1.385 0.167,0.156 10 false *2 0.802,0.563 0.979,0.729 0.177,0.167 10 false *1

Using a screwdriver, remove the snap ring from the planetary ring gear.

Text in Illustration
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


b.

Remove the planetary ring gear flange from the planetary ring gear.


Hide 35682A 56.REMOVE NO. 2 BRAKE DISC

a.
C141524

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C359886E01
1.188,1.677 1.188,0.875 1.188,0.875 1.292,0.875 false 2.125,0.51 2.302,0.51 false 2.177,1 2.292,1 false 2.198,1.188 2.406,1.188 false 2.177,1.396 2.292,1.396 false 2.177,1.594 2.292,1.594 false 2.177,0.781 2.292,0.781 2.292,0.781 2.292,1.594 false 1.188,1.073 1.302,1.073 false 1.188,1.677 1.302,1.677 false 1.188,1.479 1.302,1.479 false 1.063,1.281 1.292,1.281 false 2.344,0.438 2.656,0.635 0.313,0.198 10 false *1 2.448,1.115 2.76,1.313 0.313,0.198 10 false *3 0.875,1.208 1.188,1.406 0.313,0.198 10 false *2

Remove the No. 2 brake flange, 5 No. 2 brake discs and 5 No. 2 brake plates from the transaxle case sub-assembly.

Text in Illustration
*1 No. 2 Brake Flange
*2 No. 2 Brake Plate
*3 No. 2 Brake Disc


Hide 35068C 58.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C136482

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C136484

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.


Hide 35068C 59.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 35622G 60.REMOVE NO. 2 BRAKE PISTON

a.
C136485

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the ATF hole to remove the No. 2 brake piston from the transaxle case sub-assembly.


b.
C136673E08
1.948,0.49 2.594,0.49 false 1.375,1.208 0.917,1.208 false 0.688,1.115 0.844,1.292 0.156,0.177 10 false *1 2.646,0.396 2.802,0.573 0.156,0.177 10 false *1

Using a screwdriver, remove the 2 O-rings from the No. 2 brake piston.

Text in Illustration
*1 O-ring

HINT:

Tape the screwdriver tip before use.



Hide 35720 61.REMOVE FRONT PLANETARY GEAR ASSEMBLY

a.
C136674E04
2.62,1.242 2.965,1.407 0.346,0.165 10 SST 1.76,1.752 2.585,1.334 2.585,1.334 1.884,2.015 false

Using SST and a press, remove the front planetary gear assembly from the transaxle case sub-assembly.

SST
09950-60010  (09951-00580)
09950-70010  (09951-07100)


Hide 35782C 62.REMOVE COUNTER DRIVE GEAR

NOTICE:

Perform this procedure only when the counter drive gear bearing or transaxle case sub-assembly is replaced.


a.
C274813E02
1.323,1.333 0.698,0.542 0.698,0.542 1.427,1.188 true 0.938,3.042 1.313,2.948 1.313,2.948 1.031,3.24 false 0.417,0.417 0.875,0.615 0.458,0.198 10 false SST 1.375,2.833 1.833,3.031 0.458,0.198 10 false SST

Using SST and a press, remove the counter drive gear and bearing inner race (rear side) from the transaxle case sub-assembly.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)


b.
C295183

As shown in the illustration, tighten 3 service bolts evenly to make a clearance of approximately 20.0 mm (0.787 in.) between the counter drive gear and bearing inner race (front side).


c.
C194894E07
0.49,1.51 0.406,1.667 0.406,1.667 0.896,1.49 true 2.344,0.833 2.438,0.833 2.438,0.833 2.26,1.26 false 2.875,0.844 2.771,1.156 false 1.656,0.385 1.833,0.573 0.177,0.188 10 false *a 0.094,0.677 0.271,0.865 0.177,0.188 10 false *b 0.104,1.594 0.427,1.76 0.323,0.167 10 false SST 2.885,0.698 3.208,0.865 0.323,0.167 10 false SST 2.063,0.75 2.385,0.917 0.323,0.167 10 false SST

Using SST, remove the bearing inner race (front side) from the counter drive gear.

Text in Illustration
*a Turn
*b Hold

SST
09950-00020  
09950-00030  
09950-60020  (09951-00710)


Hide 35623 63.REMOVE NO. 3 BRAKE PISTON

a.
C136678

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C136679E04
0.816,0.427 0.975,0.582 0.159,0.155 10 *2 1.008,0.509 1.114,0.509 1.114,0.509 1.459,0.888 false 2.309,0.229 2.462,0.381 0.154,0.152 10 *1 2.281,0.311 2.031,0.311 false

Remove the brake piston return spring from the transaxle case sub-assembly.

Text in Illustration
*1 Brake Piston Return Spring
*2 No. 3 Brake Piston


c.

Remove the No. 3 brake piston from the transaxle case sub-assembly.


Hide 35409 64.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C201354

Remove the bolt, cover and manual detent spring sub-assembly from the transaxle case sub-assembly.


Hide 35501 65.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

a.
C289567

Remove the parking lock rod sub-assembly from the manual valve lever shaft sub-assembly.

HINT:

Align the protrusions with the notches on the manual valve lever shaft sub-assembly to remove the parking lock rod sub-assembly.



Hide 66.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C201356

Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the manual valve lever shaft sub-assembly.


b.
C288352

Remove the manual valve lever shaft sub-assembly from the transaxle case sub-assembly.


Hide 35506F 67.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C299161

Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case sub-assembly.

HINT:

Tape the screwdriver tip before use.