Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT SOLENOID VALVE
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292126 SHIFT SOLENOID VALVE G

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT SOLENOID VALVE  INSPECTION  


PROCEDURE

Hide 1.INSPECT SHIFT SOLENOID VALVE SL

a.
C133217

Measure the resistance according to the value(s) in the table below.

Standard resistance
Tester Connection Specified Condition
20°C (68°F)
Solenoid Connector (SL) - Solenoid Body (SL) 11 to 15 Ω

If the value is not as specified, replace the shift solenoid valve.


b.
C133218

Connect the positive (+) lead to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the shift solenoid valve.

OK:

The solenoid makes an operating noise.


If the operation cannot be done as specified, replace the shift solenoid valve.


Hide 2.INSPECT SHIFT SOLENOID VALVE SLT

a.
U190013E02
0.063,0.052 1.74,0.375 1.677,0.323 10 false Shift Solenoid Valve SLT: 0.615,0.531 0.74,0.74 0.125,0.208 10 false 1 2.51,0.479 2.635,0.688 0.125,0.208 10 false 2 2.698,2.635 2.823,2.844 0.125,0.208 10 false 2 0.656,2.792 0.781,3 0.125,0.208 10 false 1 1.219,4.229 1.427,4.458 0.208,0.229 10 false (-) 1.885,4.219 2.094,4.448 0.208,0.229 10 false (+)

Measure the resistance according to the value(s) in the table below.

Standard resistance
Tester Connection Specified Condition
20°C (68°F)
1 - 2 5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.


b.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the shift solenoid valve.

OK:

The solenoid makes an operating noise.


If the operation cannot be done as specified, replace the shift solenoid valve.


Hide 3.INSPECT SHIFT SOLENOID VALVE SLU

a.
G102540E04
1.76,3.115 2.469,2.76 false 1.49,3.115 0.781,2.802 false 0.771,1.24 1.479,0.885 false 2.49,1.219 1.781,0.906 false 0.115,0.063 1.938,0.385 1.823,0.323 10 false Shift Solenoid Valve SLU: 0.646,1.177 0.958,1.375 0.313,0.198 10 false 1 2.552,1.167 2.865,1.365 0.313,0.198 10 false 2 1.198,4.167 1.51,4.365 0.313,0.198 10 false (-) 1.917,4.177 2.229,4.375 0.313,0.198 10 false (+) 0.635,2.698 0.948,2.896 0.313,0.198 10 false 1 2.531,2.656 2.844,2.854 0.313,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard resistance
Tester Connection Specified Condition
20°C (68°F)
1 - 2 5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.


b.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the shift solenoid valve.

OK:

The solenoid makes an operating noise.


If the operation cannot be done as specified, replace the shift solenoid valve.


Hide 35220 4.INSPECT SHIFT SOLENOID VALVE SL2

a.
G102540E02
1.76,3.115 2.469,2.76 false 1.49,3.115 0.781,2.802 false 1.76,0.906 2.469,0.552 false 1.479,0.896 0.771,0.583 false 0.115,0.063 1.938,0.385 1.823,0.323 10 false Shift Solenoid Valve SL2: 0.625,0.479 0.938,0.677 0.313,0.198 10 false 1 2.542,0.458 2.854,0.656 0.313,0.198 10 false 2 1.198,4.167 1.51,4.365 0.313,0.198 10 false (-) 1.917,4.177 2.229,4.375 0.313,0.198 10 false (+) 0.635,2.698 0.948,2.896 0.313,0.198 10 false 1 2.531,2.656 2.844,2.854 0.313,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard resistance
Tester Connection Specified Condition
20°C (68°F)
1 - 2 5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.


b.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the shift solenoid valve.

OK:

The solenoid makes an operating noise.


If the operation cannot be done as specified, replace the shift solenoid valve.


Hide 35210 5.INSPECT SHIFT SOLENOID VALVE SL1

a.
G102540E01
1.76,3.115 2.469,2.76 false 1.49,3.115 0.781,2.802 false 1.76,0.906 2.469,0.552 false 1.479,0.896 0.771,0.583 false 0.115,0.063 1.938,0.385 1.823,0.323 10 false Shift Solenoid Valve SL1: 0.625,0.479 0.938,0.677 0.313,0.198 10 false 1 2.542,0.458 2.854,0.656 0.313,0.198 10 false 2 1.198,4.167 1.51,4.365 0.313,0.198 10 false (-) 1.917,4.177 2.229,4.375 0.313,0.198 10 false (+) 0.635,2.698 0.948,2.896 0.313,0.198 10 false 1 2.531,2.656 2.844,2.854 0.313,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard resistance
Tester Connection Specified Condition
20°C (68°F)
1 - 2 5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.


b.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the shift solenoid valve.

OK:

The solenoid makes an operating noise.


If the operation cannot be done as specified, replace the shift solenoid valve.


Hide 6.INSPECT SHIFT SOLENOID VALVE SL3

a.
G102540E03
1.76,3.115 2.469,2.76 false 1.49,3.115 0.781,2.802 false 1.76,0.906 2.469,0.552 false 1.479,0.896 0.771,0.583 false 0.115,0.063 1.938,0.385 1.823,0.323 10 false Shift Solenoid Valve SL3: 0.625,0.479 0.938,0.677 0.313,0.198 10 false 1 2.542,0.458 2.854,0.656 0.313,0.198 10 false 2 1.198,4.167 1.51,4.365 0.313,0.198 10 false (-) 1.917,4.177 2.229,4.375 0.313,0.198 10 false (+) 0.635,2.698 0.948,2.896 0.313,0.198 10 false 1 2.531,2.656 2.844,2.854 0.313,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard resistance
Tester Connection Specified Condition
20°C (68°F)
1 - 2 5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.


b.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the shift solenoid valve.

OK:

The solenoid makes an operating noise.


If the operation cannot be done as specified, replace the shift solenoid valve.


Hide 7.INSPECT SHIFT SOLENOID VALVE SL4

a.
G102540E05
1.76,3.115 2.469,2.76 false 1.49,3.115 0.781,2.802 false 1.76,0.906 2.51,0.656 false 1.448,0.896 0.74,0.688 false 0.115,0.063 1.938,0.385 1.823,0.323 10 false Shift Solenoid Valve SL4: 0.573,0.583 0.885,0.781 0.313,0.198 10 false 1 2.573,0.552 2.885,0.75 0.313,0.198 10 false 2 1.198,4.167 1.51,4.365 0.313,0.198 10 false (-) 1.917,4.177 2.229,4.375 0.313,0.198 10 false (+) 0.635,2.698 0.948,2.896 0.313,0.198 10 false 1 2.531,2.656 2.844,2.854 0.313,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard resistance
Tester Connection Specified Condition
20°C (68°F)
1 - 2 5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.


b.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the shift solenoid valve.

OK:

The solenoid makes an operating noise.


If the operation cannot be done as specified, replace the shift solenoid valve.