Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE › from 2014.09
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292127 DIFFERENTIAL CASE A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41311F 1.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C303568E04
0.958,0.708 1.438,0.604 1.438,0.604 1.083,0.854 false 2.573,0.573 2.375,0.479 2.375,0.479 2.479,0.75 false 1.479,0.521 1.833,0.708 0.354,0.188 10 false SST 2.083,0.385 2.438,0.573 0.354,0.188 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the front differential case.

SST
09726-36010  
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case rear tapered roller bearing (inner race) cage when installing the front differential case rear tapered roller bearing (inner race).

·

Ensure that there is no clearance between the front differential case rear tapered roller bearing (inner race) and front differential case.




b.
C196828E10
0.896,1.115 0.563,1.385 0.563,1.385 0.729,1.385 false 2.635,1.104 2.594,0.792 2.594,0.792 2.677,0.792 false 0.271,1.313 0.563,1.542 0.292,0.229 10 true SST 2.302,0.708 2.615,0.865 0.313,0.156 10 false SST

Using SST and a hammer, install a new front differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case rear tapered roller bearing (outer race) and transaxle case sub-assembly.



Hide 41311E 2.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C316147E01
0.105,0.366 0.460,0.562 0.355,0.196 10 SST 0.932,0.569 0.481,0.462 0.481,0.462 0.83,0.827 false 0.481,0.462 0.853,0.696 false 2.974,0.169 3.329,0.365 0.355,0.196 10 SST 2.583,0.353 2.941,0.264 2.941,0.264 2.757,0.43 false 2.941,0.264 2.774,0.605 false

Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the front differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case front tapered roller bearing (inner race) cage when installing the front differential case front tapered roller bearing (inner race).

·

Ensure that there is no clearance between the front differential case front tapered roller bearing (inner race) and front differential case.




b.

Install the shim to the transaxle housing.


c.
C196830E09
0.948,1.219 0.625,1.594 0.625,1.594 0.896,1.51 true 2.604,0.729 2.521,0.729 2.521,0.729 2.542,1.083 false 0.313,1.521 0.615,1.688 0.302,0.167 10 false SST 2.24,0.594 2.542,0.76 0.302,0.167 10 false SST

Using SST and a hammer, install a new front differential case front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case front tapered roller bearing (outer race), shim and transaxle housing.



Hide 3.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C288461E08
0.813,0.698 0.813,0.25 0.813,0.25 0.677,0.25 false 1.729,0.75 1.729,0.25 1.729,0.25 1.594,0.25 false 2.51,0.719 2.51,0.25 2.51,0.25 2.375,0.25 false 0.5,0.167 0.719,0.365 0.219,0.198 10 false *1 1.406,0.167 1.625,0.365 0.219,0.198 10 false *2 2.188,0.167 2.406,0.365 0.219,0.198 10 false *3

Coat the front differential side gear, front No. 1 differential side gear thrust washer and conical spring with ATF.

Text in Illustration
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

ATF


b.
C309130E08
2.417,0.177 2.208,0.177 false 2.448,0.313 2.229,0.313 false 2.354,0.688 2.229,0.688 false 2.333,1.281 2.229,1.281 false 2.448,1.708 2.26,1.708 false 2.417,1.865 2.26,1.865 false 2.042,0.615 2.323,0.844 0.281,0.229 10 false *1 2.052,1.208 2.333,1.438 0.281,0.229 10 false *1 2.052,0.25 2.333,0.479 0.281,0.229 10 false *2 2.073,1.604 2.354,1.833 0.281,0.229 10 false *2 2.063,1.781 2.344,2.01 0.281,0.229 10 false *3 2.042,0.094 2.323,0.323 0.281,0.229 10 false *3

Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs to the front differential case.

Text in Illustration
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer

NOTICE:
·

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring.

·

Make sure that the conical spring is installed with the correct orientation.




c.

Install SST as shown in the illustration and tighten it.

C312291E04
5.052,1.396 4.906,1.521 4.906,1.521 5.052,1.667 false 4.917,1.521 4.469,1.521 false 5.135,0.271 4.677,0.271 false 3.156,0.198 3.375,0.469 0.219,0.271 10 false *a 4.396,0.188 4.719,0.396 0.323,0.208 10 false SST 4.208,1.438 4.531,1.646 0.323,0.208 10 false SST 1.052,2.365 1.271,2.635 0.219,0.271 10 false *b

Text in Illustration
*a Turn *b Hold

SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




d.
C312282

Coat the front differential pinion and front differential pinion thrust washer with ATF.

Text in Illustration
V100135

ATF


e.
C309133E04
2.479,2.281 2.479,2.875 2.479,2.875 2.656,2.875 false 2.688,2.792 3.052,2.979 0.365,0.188 10 false SST 1.969,0.615 2.292,0.865 0.323,0.25 10 false *a

Using SST as shown in the illustration, rotate the front differential side gear and install the 2 front differential pinions and 2 front differential pinion thrust washers.

Text in Illustration
*a Turn

SST
09528-52010  (09528-05030)

CAUTION:

Be careful not to catch your fingers between the front differential pinion and front differential case.


NOTICE:

Do not drop the front differential pinion or front differential pinion thrust washer.



Hide 41342F 5.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C309134

Coat the front No. 1 differential pinion shaft with ATF.

Text in Illustration
V100135

ATF


b.

Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.


Hide 41342A 7.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C309135

Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C309136

Using a chisel and hammer, stake the front differential case.


Hide 8.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.


b.
C205239

Install the front differential case to the transaxle case sub-assembly.


c.
C136447E13
2.921,0.092 3.052,0.245 0.132,0.152 10 A 2.503,1.866 2.634,2.018 0.132,0.152 10 B 1.51,1.618 2.486,1.958 2.486,1.958 2.219,1.657 false 1.905,1.645 2.486,1.958 false 0.385,0.161 0.517,0.313 0.132,0.152 10 A 3.088,1.029 3.220,1.181 0.132,0.152 10 A 0.516,1.783 0.648,1.935 0.132,0.152 10 A 1.212,1.952 1.344,2.104 0.132,0.152 10 A 2.584,0.92 3.062,1.106 3.062,1.106 2.508,1.416 false 3.062,1.106 2.617,1.149 false 2.032,0.602 2.895,0.191 2.895,0.191 2.298,0.742 false 1.796,0.505 2.879,0.198 false 1.28,1.948 1.313,1.737 false 1.354,0.438 0.553,0.273 0.553,0.273 0.848,0.717 false 1.148,0.511 0.553,0.273 0.553,0.273 1.025,0.614 false 0.087,1.267 0.218,1.420 0.132,0.152 10 A 0.593,1.021 0.229,1.351 0.229,1.351 0.675,1.607 false 0.57,1.399 0.229,1.351 0.229,1.351 0.544,1.198 false 0.871,1.757 0.658,1.875 0.658,1.875 1.088,1.806 false

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt (A) : 31 N*m (316 kgf*cm, 23 ft.*lbf)
Bolt (B) : 23 N*m (234 kgf*cm, 17 ft.*lbf)


d.
C138262E06
0.841,4.027 1.204,4.212 0.364,0.184 10 SST 1.079,3.308 0.973,4.027 false

Using SST, turn the front differential case right and left 2 or 3 times to settle the bearing.

SST
09564-33010  


e.

Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.

SST
09564-33010  

Turning Torque:

0.8 to 1.4 N*m (8 to 14 kgf*cm, 7 to 12 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness
Part No. Thickness
(mm (in.))
90564-79054 2.000 (0.0787)
90564-79055 2.025 (0.0797)
90564-79056 2.050 (0.0807)
90564-79057 2.075 (0.0817)
90564-79058 2.100 (0.0827)
90564-79059 2.125 (0.0837)
90564-79060 2.150 (0.0846)
90564-79061 2.175 (0.0856)
90564-79062 2.200 (0.0866)
90564-79063 2.225 (0.0876)
90564-79064 2.250 (0.0886)
90564-79065 2.275 (0.0896)
90564-79066 2.300 (0.0906)
90564-79067 2.325 (0.0915)
90564-79068 2.350 (0.0925)
90564-79069 2.375 (0.0935)
90564-79070 2.400 (0.0945)
90564-79071 2.425 (0.0955)
90564-79072 2.450 (0.0965)
90564-79073 2.475 (0.0974)
90564-79074 2.500 (0.0984)
90564-79075 2.525 (0.0994)
90564-79076 2.550 (0.100)
90564-79077 2.575 (0.101)
90564-79078 2.600 (0.102)
90564-79079 2.625 (0.103)
90564-79080 2.650 (0.104)
90564-79081 2.675 (0.105)
90564-79082 2.700 (0.106)
90564-79083 2.725 (0.107)
90564-79084 2.750 (0.108)
90564-79085 2.775 (0.109)
90564-79086 2.800 (0.110)
90564-79087 2.825 (0.111)
90564-79088 2.850 (0.112)
90564-79089 2.875 (0.113)


f.
C287968

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


g.
C205239

Remove the front differential case from the transaxle case sub-assembly.


Hide 41221 9.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.
C138531E13
1.252,1.454 0.655,1.147 0.655,1.147 1.172,1.508 false 0.438,1.043 0.664,1.222 0.226,0.179 10 *a

Clean the contact surface of the front differential case.

Text in Illustration
*a Matchmark


c.

Align the matchmarks, and install the front differential ring gear to the front differential case quickly.


d.
C138532

Install the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.




Hide 31105H 10.INSTALL TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new transaxle case oil seal with MP grease.


b.
C307977E06
1.385,1.198 0.479,2.073 0.479,2.073 1.333,1.49 true 1.781,1.802 2.604,1.802 true 2.354,1.948 2.479,1.948 2.479,1.948 2.479,1.802 false 0.177,2.031 0.521,2.219 0.344,0.188 10 false SST 2.646,1.719 3.052,1.906 0.406,0.188 10 true SST

Using SST and a hammer, install the transaxle case oil seal to the transaxle case sub-assembly.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the transaxle case oil seal is installed in the correct direction.



Hide 31105D 11.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C307978E05
2.479,1.844 2.229,1.844 false 0.938,0.698 0.625,0.396 0.625,0.396 0.469,0.396 true 1.938,1.771 2.323,1.99 0.385,0.219 10 false SST 0.167,0.313 0.552,0.531 0.385,0.219 10 false SST

Coat the lip of a new front transaxle case oil seal with MP grease.


b.

Using SST and a hammer, install the front transaxle case oil seal to the transaxle housing.

SST
09308-14010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the front transaxle case oil seal is installed in the correct direction.