Home › Drivetrain › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM24M0E _52 Drivetrain _059580 DRIVE SHAFT _0292135 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT  FRONT DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 43448G 1.REMOVE FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP LH

C127644E02
0.079,0.032 1.253,0.192 1.174,0.161 10 One Touch Type: 0.053,2.119 1.693,2.307 1.640,0.188 10 Claw Engagement Type: 0.553,3.182 1.220,3.348 0.667,0.166 10 Claw Part 0.525,3.255 0.402,3.206 false

a.

One Touch Type:

i.

Using a screwdriver, remove the inboard joint boot clamp, as shown in the illustration.



b.

Claw Engagement Type:

i.

Using needle-nose pliers, remove the inboard joint boot clamp, as shown in the illustration.



Hide 43448E 2.REMOVE FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:

Use the same procedures described for the LH side.


Hide 43448F 3.REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP LH

C127645E02
0.067,0.058 1.253,0.240 1.187,0.182 10 One Touch Type: 0.081,2.171 1.715,2.329 1.634,0.158 10 Claw Engagement Type: 0.513,3.214 1.189,3.373 0.676,0.158 10 Claw Part 0.498,3.294 0.381,3.294 false

a.

One touch type:

i.

Using a screwdriver, remove the inboard joint boot clamp, as shown in the illustration.



b.

Claw engagement type:

i.

Using needle-nose pliers, remove the inboard joint boot clamp, as shown in the illustration.



Hide 43448C 4.REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedures described for the LH side.


Hide 5.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the boot from the inboard joint.


Hide 43040 6.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH

C127646E02
0.209,0.15 0.932,0.307 0.723,0.158 10 Matchmark 2.187,0.371 1.082,0.24 false 1.836,0.805 1.082,0.24 false

a.

Remove any old grease from the inboard joint.


b.

Put matchmarks on the inboard joint and outboard joint shaft.

NOTICE:

Do not punch the marks.



c.

Remove the inboard joint from the outboard joint shaft.


d.
C127648

Using a snap ring expander, remove the shaft snap ring.


e.
C127649E01
2.538,1.75 3.249,1.902 0.711,0.152 10 Matchmark 2.836,0.817 2.984,1.723 false 2.984,1.723 2.729,0.765 false

Put matchmarks on the outboard joint shaft and tripod joint.

NOTICE:

Do not punch the marks.



f.

Using a brass bar and hammer, tap out the tripod joint from the outboard joint shaft.

NOTICE:

Do not tap the rollers.



g.

Remove the inboard joint boot.


Hide 43474G 7.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP LH (w/ 1 Clamp)

C127651E37
0.573,4.188 0.458,4.177 false 0.063,0.063 1.24,0.333 1.177,0.271 10 true One Touch Type: 0.073,2.292 1.708,2.458 1.635,0.167 10 false Claw Engagement Type: 0.583,4.104 1.219,4.25 0.635,0.146 10 false Claw Part

a.

One Touch Type:

i.

Using a screwdriver, remove the front drive shaft damper clamp LH, as shown in the illustration.



b.

Claw Engagement Type:

i.

Using needle-nose pliers, remove the front drive shaft damper clamp LH, as shown in the illustration.



Hide 43474G 8.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP LH (w/ 2 Clamps)

a.
C205160E04
2.205,0.708 2.426,0.889 0.222,0.181 10 *a 1.879,0.642 2.289,0.693 false 2.289,0.694 2.607,0.487 false

Using needle-nose pliers, remove the 2 front drive shaft damper clamps LH, as shown in the illustration.

*a Claw


Hide 43474E 9.REMOVE FRONT DRIVE SHAFT DAMPER LH

a.

Remove the front drive shaft damper LH from the front drive outboard joint shaft assembly.


Hide 43447F 10.REMOVE FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP

C127653

a.

Using a screwdriver, remove the outboard joint boot clamp, as shown in the illustration.


Hide 43447E 11.REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

C142001

a.

Using a screwdriver, remove the outboard joint boot clamp, as shown in the illustration.


Hide 12.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the outboard joint boot from the outboard joint shaft.


b.

Remove any old grease from the outboard joint.


Hide 43420G 13.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

C127655

a.

Using a screwdriver, remove the hole snap ring.


Hide 41336E 14.REMOVE FRONT DRIVE SHAFT DUST COVER LH

C127659E01
0.365,1.653 0.670,1.803 0.305,0.150 10 SST 0.745,1.713 1.145,1.362 false

a.

Using SST and a press, press out the shaft dust cover.

SST
09950-00020  

NOTICE:

Be careful not to drop the inboard joint.



Hide 41336D 15.REMOVE FRONT DRIVE SHAFT DUST COVER RH

HINT:

Use the same procedures described for the LH side.


Hide 43045 16.REMOVE DRIVE SHAFT BEARING CASE SUB-ASSEMBLY

C127662

a.

Using a screwdriver, remove the bearing case snap ring.


b.
C127663

Using a press, press out the drive shaft bearing case.

NOTICE:

Be careful not to drop the inboard joint.



Hide 43458 17.REMOVE FRONT DRIVE SHAFT DUST COVER

a.

w/ Cover:

i.
C127664E01
0.208,1.394 0.498,1.540 0.290,0.146 10 SST 1.155,1.605 0.582,1.487 false

Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly.

SST
09950-00020  

NOTICE:
·

Do not drop the front drive inboard joint assembly.


·

Do not overtighten SST.



HINT:

If the front drive shaft dust cover is removed, it is not necessary to reinstall it.




Hide 43410C 18.REMOVE FRONT DRIVE SHAFT BEARING

C127665

a.

Using a snap ring expander, remove the snap ring.


b.
C127666E12
2.729,1.469 2.396,1.469 false 2.781,1.385 3.094,1.542 0.313,0.156 10 false SST

Using SST and a press, press out the drive shaft bearing.

SST
09527-10011  


c.

Remove the snap ring.