Home › Drivetrain › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM24M0E _52 Drivetrain _059580 DRIVE SHAFT _0292135 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 43045 1.INSTALL DRIVE SHAFT BEARING CASE SUB-ASSEMBLY

C127674E11
1.052,1.656 0.531,1.656 false 0.719,0.479 0.719,0.281 0.719,0.281 0.573,0.271 false 2.813,1.438 2.917,1.438 false 0.26,0.188 0.573,0.354 0.313,0.167 10 false SST 0.188,1.573 0.5,1.74 0.313,0.167 10 false SST 2.948,1.354 3.26,1.521 0.313,0.167 10 false SST

a.

Using SST and a press, press in the drive shaft bearing case to the inboard joint RH.

SST
09527-10011  
09710-04081  

NOTICE:

The bearing should be installed completely.



b.
C127675

Using a snap ring expander, install a new drive shaft hole snap ring.


Hide 41336D 2.INSTALL FRONT DRIVE SHAFT DUST COVER RH

C127678E01
1.378,0.113 1.686,0.262 0.308,0.148 10 SST 1.343,0.181 1.047,0.366 false 2.106,1.843 2.692,1.999 0.586,0.156 10 Distance 2.853,1.184 2.539,1.441 false 2.539,1.429 2.539,1.859 false

a.

Using SST and a press, press in a new drive shaft dust cover until the distance from the tip of the center drive shaft to the drive shaft dust cover reaches the specification, as shown in the illustration.

SST
09527-10011  

Standard distance:
for 2GR-FE 110.0 to 111.0 mm (4.33 to 4.37 in.)
for 2AZ-FE 91.0 to 92.0 mm (3.58 to 3.62 in.)


NOTICE:
·

Be careful of the installation direction of the dust cover.

·

Be careful not to damage the dust cover.




Hide 41336E 3.INSTALL FRONT DRIVE SHAFT DUST COVER LH

C127677E01
0.096,0.219 0.389,0.378 0.292,0.160 10 SST 0.654,0.617 0.654,0.311 false 0.654,0.311 0.429,0.311 false 0.745,0.074 1.481,0.233 0.735,0.160 10 Dust Cover 2.256,0.795 1.742,0.167 false 1.742,0.167 1.634,0.167 false

a.

Using SST and a press, press in a new drive shaft dust cover.

SST
09527-10011  

NOTICE:
·

Be careful of the installation direction of the dust cover.

·

Be careful not to damage the dust cover.




Hide 43420G 4.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

a.

Install a new hole snap ring.


Hide 5.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

C127681E01
2.467,0.402 3.153,0.567 0.686,0.165 10 Vinyl Tape 2.41,0.481 2.096,0.481 false 2.096,0.481 1.758,0.752 false

HINT:

Before installing the boots, wrap the spline of the drive shaft with vinyl tape to prevent the boots from being damaged.


a.

Install new parts to the outboard joint shaft in the following order.

i.

No. 2 outboard joint boot clamp


ii.

Outboard joint boot


iii.

Outboard joint boot clamp



b.

Pack the outboard joint shaft and boot with grease from the boot kit.

Standard grease capacity:
for 2GR-FE 205 to 215 g (7.23 to 7.58 oz.)
for 2AZ-FE 171 to 181 g (6.03 to 6.38 oz.)



Hide 43447F 6.INSTALL FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP LH

CAUTION:

Wear protective gloves while performing the operation and be careful to avoid cutting your hands or other body parts.


a.
C415871C01
2.156,1.5 2.677,1.5 false 0.833,1.24 1.354,1.24 false 1.917,2.031 2.438,2.031 false 2.708,1.438 3.021,1.594 0.313,0.156 10 false *a 0.667,1.177 0.979,1.333 0.313,0.156 10 false *b 1.729,1.948 2.042,2.104 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Install the front axle outboard joint boot No. 2 clamp to the outboard joint boot and temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




b.

As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415872C01
3.604,1.052 3.135,1.406 3.135,1.406 3.708,1.042 true 2.083,1.49 1.594,1.49 true 1.958,2.281 1.688,2.281 1.688,2.281 1.448,1.906 true 5.927,2.229 5.646,1.938 5.646,1.938 5.49,1.938 true 3.823,0.292 4.135,0.448 0.313,0.156 10 false *a 4.104,1.302 4.417,1.458 0.313,0.156 10 false *b 5.24,0.583 5.552,0.74 0.313,0.156 10 false *c 2.979,1.354 3.292,1.51 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.417 1.74,1.573 0.313,0.156 10 false *d 2.01,2.219 2.323,2.375 0.313,0.156 10 false *e 5.281,1.875 5.594,2.031 0.313,0.156 10 false *d
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Do not damage the deflector.

·

Make sure that the outboard joint is in direct contact with the work surface.




c.
C127685

Using a plastic-faced hammer, fix the buckle into place by tapping it. At the same time, use the plastic-faced hammer to adjust the lift of the lever so that the gaps between the buckle flange and lever end flange become even.

NOTICE:

Do not damage the boot.



Hide 43447D 7.INSTALL FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:

Use the same procedures described for the LH side.


Hide 43447E 8.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

C129510

CAUTION:

Wear protective gloves while performing the operation and be careful to avoid cutting your hands or other body parts.


a.

Install a new boot clamp to the outboard joint boot and temporarily bend the lever.

NOTICE:

When temporarily bending the lever, make sure not to deform the band and lever.



b.
C129511

Using water pump pliers, temporarily lock the boot clamp by clamping it down until a "click" sound is heard.


c.
C129512

Using a plastic-faced hammer, fix the buckle into place by tapping it. At the same time, use the plastic-faced hammer to adjust the lift of the lever so that the gaps between the buckle flange and lever end flange become even.

NOTICE:

Do not strike the drive shaft forcefully with the plastic-faced hammer.



Hide 43447C 9.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedures described for the LH side.


Hide 43474E 10.INSTALL FRONT DRIVE SHAFT DAMPER LH (w/ 1 Clamp)

a.

Install a new front drive shaft damper clamp LH onto the front drive outboard joint shaft assembly.


b.
C240143E05
0.74,1.427 0.74,1.719 false 1.219,1.74 1.219,1.333 false 1.656,0.542 1.875,0.719 0.219,0.177 10 false (A) 1.146,1.729 1.323,1.906 0.177,0.177 10 false *2 0.656,1.74 0.833,1.917 0.177,0.177 10 false *1

Install the front drive shaft damper LH onto the front drive outboard joint shaft assembly.

Text in Illustration
*1 Front Drive Shaft Damper LH
*2 Front Drive Shaft Damper Clamp LH


c.

Set the dimension as specified below.

Dimension (A):
for 2GR-FE 158.0 to 162.0 mm (6.22 to 6.37 in.)
for 2AR-FE 161.0 to 165.0 mm (6.34 to 6.49 in.)



d.

Install the front drive shaft damper clamp LH onto the front drive shaft damper LH.

NOTICE:

Be sure to install the clamp in the correct position.



e.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



f.
C127651E38
0.448,4.146 0.625,4.146 false 0.125,0.094 1.24,0.302 1.115,0.208 10 true One Touch Type: 0.135,2.323 1.698,2.49 1.563,0.167 10 false Claw Engagement Type: 0.635,4.052 1.292,4.292 0.656,0.24 10 false Claw Part

One Touch Type:

i.

Using a screwdriver, install the front drive shaft damper clamp LH.



g.

Claw Engagement Type:

i.

Using needle nose pliers, install the front drive shaft damper clamp LH.



Hide 43474E 11.INSTALL FRONT DRIVE SHAFT DAMPER LH (w/ 2 Clamps)

a.
C324681E05
0.188,1.25 0.188,1.625 false 0.646,1.333 0.646,1.604 false 1.229,1.25 1.229,1.625 false 1.427,0.406 1.625,0.583 0.198,0.177 10 false (A) 0.573,1.625 0.729,1.802 0.156,0.177 10 false *1 1.156,1.635 1.313,1.813 0.156,0.177 10 false *2 0.115,1.646 0.271,1.823 0.156,0.177 10 false *2

Temporarily install the front drive shaft damper LH and 2 new front drive shaft damper clamps LH to the front drive outboard joint shaft assembly as shown in the illustration.

Text in Illustration
*1 Front Drive Shaft Damper LH
*2 Front Drive Shaft Damper Clamp LH


b.

Set the dimension as specified below.

Dimension (A):
for 2GR-FE 212.5 to 216.5 mm (8.37 to 8.52 in.)
for 2AR-FE 199.0 to 203.0 mm (7.84 to 7.99 in.)



c.

Install the 2 front drive shaft damper clamps LH onto the front drive shaft damper LH.

NOTICE:

Be sure to install the clamp in the correct position.



d.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C205160E05
2.444,1.248 2.676,1.421 0.232,0.173 10 *a 2.663,0.648 2.529,1.238 2.529,1.238 1.843,0.853 false

Using needle nose pliers, install the 2 front drive shaft damper clamps LH.

Text in Illustration
*a Claw


Hide 43040 12.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY LH

a.

Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boots from being damaged.


b.

Install new parts to the outboard joint shaft in the following order.

i.

Inboard joint boot clamp


ii.

No. 2 inboard joint boot clamp


iii.

Inboard joint clamp



c.
C127694E19
1.938,1.198 2.177,1.792 2.177,1.792 1.365,1.531 false 2.25,1.729 2.979,1.896 0.729,0.167 10 false Matchmark

Place the beveled side of the tripod axial spline toward the outboard joint.


d.

Align the matchmarks placed before removal.


e.

Using a brass bar and hammer, tap the tripod joint onto the drive shaft.

NOTICE:
·

Do not tap the rollers.

·

Be sure to install the tripod joint in the correct direction.




f.
C127695

Using a snap ring expander, install a new shaft snap ring.


g.

Pack the inboard joint shaft and boot with grease from the boot kit.

Standard grease capacity:

175 to 185 g (6.17 to 6.52 oz.)



h.

Align the matchmarks, and install the inboard joint to the outboard joint shaft.


Hide 43030 13.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 14.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the inboard joint boot to the inboard joint.


Hide 43448F 15.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP LH

C127696E02
0.098,0.035 1.255,0.173 1.156,0.138 10 One Touch Type: 0.112,2.099 1.746,2.262 1.634,0.164 10 Claw Engagement Type: 0.55,3.142 1.203,3.316 0.654,0.174 10 Claw Part 0.526,3.228 0.409,3.228 false

a.

One touch type:

i.

Using a screwdriver, install the inboard joint boot clamp, as shown in the illustration.

NOTICE:

Be careful not to damage the boot.




b.

Claw engagement type:

i.

Using needle-nose pliers, install the inboard joint boot clamp, as shown in the illustration.

NOTICE:

Be careful not to damage the boot.




Hide 43448C 16.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedures described for the LH side.


Hide 43448G 17.INSTALL FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP LH

C127697E02
0.08,0.076 1.279,0.276 1.199,0.200 10 One Touch Type: 0.1,2.128 1.739,2.297 1.639,0.169 10 Claw Engagement Type: 0.661,3.196 1.339,3.372 0.679,0.177 10 Claw Part 0.42,3.178 0.615,3.28 false

a.

One Touch Type:

i.

Using a screwdriver, install the inboard joint boot clamp, as shown in the illustration.

NOTICE:

Be careful not to damage the boot.




b.

Claw Engagement Type:

i.

Using needle-nose pliers, install the inboard joint boot clamp, as shown in the illustration.

NOTICE:

Be careful not to damage the boot.




Hide 43448E 18.INSTALL FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:

Use the same procedures described for the LH side.


Hide 19.INSPECT FRONT DRIVE SHAFT

a.
C127698

Check that there is no severe play in the radial direction of the outboard joint.


b.

Check that the inboard joint slides smoothly in the thrust direction.


c.

Check that there is no severe play in the radial direction of the inboard joint.


d.

Check the boots for damage.

NOTICE:

Keep the drive shaft assembly level during inspection.


HINT:
C127699E21
1.438,1.521 1.656,1.74 0.219,0.219 10 false (A)

For dimension (A), refer to the following values.


Dimension (A):
for 2GR-FE for LH Side 577.6 mm (1.89 ft.)
for RH Side 914.4 mm (3.00 ft.)
for 2AZ-FE for LH Side 585.2 mm (1.92 ft.)
for RH Side 902.0 mm (2.96 ft.)