Home › Suspension › SUSPENSION › FRONT WHEEL ALIGNMENT › 2013.04–2016.05
RM24M0E _53 Suspension _059582 SUSPENSION _0292142 FRONT WHEEL ALIGNMENT N

SUSPENSION  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT TIRES

Hide 2.MEASURE VEHICLE HEIGHT

C133544E01
0.199,3.972 0.335,4.121 0.135,0.149 10 C 3.095,3.899 3.230,4.048 0.135,0.149 10 D 1.808,3.899 1.943,4.048 0.135,0.149 10 B 1.367,3.9 1.503,4.049 0.135,0.149 10 A

NOTICE:

Before inspecting the wheel alignment, adjust the vehicle height to the specification.


a.

Press down on the vehicle several times to stabilize the suspension, and measure the vehicle height.


b.

Measure the front vehicle height.

i.

Measure the distance from the ground to the center of the No. 1 lower suspension arm front mounting bolt.



c.

Measure the rear vehicle height.

i.

Measure the distance from the ground to the center of the body side axle beam mounting bolt.

Standard vehicle height (unloaded vehicle):
Front C - A Rear D - B
93 mm (3.66 in.) -37 mm (-1.46 in.)


HINT:

If the vehicle height is not as specified, press down on the vehicle several times to stabilize the suspension. Then measure the vehicle height again.




Hide 3.INSPECT TOE-IN

U188218E02
0.281,0.042 0.417,0.188 0.135,0.146 10 false A 1.688,0.115 1.823,0.26 0.135,0.146 10 false D 3.083,0.052 3.219,0.198 0.135,0.146 10 false B 1.708,1.917 1.844,2.063 0.135,0.146 10 false C 1.51,0.51 1.875,0.677 0.365,0.167 10 false Front

Standard toe-in (unloaded vehicle):
Front A + B Rear C - D
A + B: 0°05' +-10' (0.09° +-0.16°) C - D: 1.0 +-2.0 mm (0.04 +-0.08 in.)


If the toe-in is not as specified, adjust it at the rack ends.


Hide 4.ADJUST TOE-IN

C133545E02
2.115,1.219 2.604,1.531 0.49,0.313 10 true Loosen 2.51,0.917 2.823,1.188 0.313,0.271 10 true Turn

a.

Remove the boot clips.


b.

Loosen the tie rod end lock nuts.


c.

Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.


d.
C133546E02
2.083,1.063 2.729,1.375 0.646,0.313 10 true Difference

Make sure that the length of the right and left rack ends are approximately the same.

Standard difference:

1.5 mm (0.059 in.) or less



e.

Tighten the tie rod end lock nuts.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)


f.

Place the boots on the seats and install the clips.

HINT:

Make sure that the boots are not twisted.



Hide 5.INSPECT WHEEL ANGLE

U190055E02
0.427,0.021 0.552,0.177 0.125,0.156 10 false A 2.729,0.021 2.854,0.177 0.125,0.156 10 false A 0.771,0.031 0.896,0.188 0.125,0.156 10 false B 2.406,0.021 2.531,0.177 0.125,0.156 10 false B 1.458,0.698 1.854,0.854 0.396,0.156 10 false Front 1.188,1.406 1.781,1.594 0.594,0.188 10 false A: Inside 1.188,1.708 1.958,1.896 0.771,0.188 10 false B: Outside

a.

Turn the steering wheel to the left and right full lock positions, and measure the turning angle.

Standard wheel angle (unloaded vehicle):
Inside Wheel Angle Outside Wheel Angle (Reference)
39°23' (37°23' to 41°23')
(39.4°(37.4° to 41.4°))
32°29'
(32.5°)


If the angles are not as specified, check and adjust the right and left rack end lengths.



Hide 6.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

Z003382

a.

Install the camber-caster-kingpin gauge or place the front wheels on the center of the wheel alignment tester.


b.

Inspect the camber, caster and steering axis inclination.

Standard camber inclination (unloaded vehicle):

-0°10' +-45' (-0.16° +-0.75°)


Standard caster inclination (unloaded vehicle):

5°45' +-45' (5.75° +-0.75°)


Standard steering axis inclination (unloaded vehicle):

11° 22' +-45' (11.36° +-0.75°)



Hide 7.ADJUST CAMBER AND CASTER

NOTICE:

After the camber has been adjusted, inspect the toe-in.


a.

Remove the front wheel.


b.
C133547

Remove the 2 nuts on the lower side of the shock absorber.


c.

Clean the installation surfaces of the shock absorber and the steering knuckle.


d.

Temporarily install the 2 nuts.


e.
C133548

Adjust the camber by pushing or pulling the lower side of the shock absorber in the direction where the camber adjustment is required.


f.

Tighten the 2 nuts.

T = 240 N*m{ 2,447 kgf*cm 177 ft.*lbf }


g.

Install the front wheel.

T = 103 N*m{ 1,050 kgf*cm 76 ft.*lbf }


h.

Check the camber.

If the measured value is not within the specified range, calculate the required adjustment amount using the formula below.

C367471E01
2.531,0.646 2.917,0.646 false 2.542,0.417 2.917,0.417 2.917,0.417 2.917,1.76 false 2.115,1.781 3.354,2.063 1.24,0.281 10 false Use Adjusting Bolt

If the camber is not within the specification, estimate how much additional camber adjustment will be required and select the camber adjusting bolt using the following table.

Camber adjustment amount:

Center of the specified range - Measured value


C131803E03
1.594,2 2.188,2.5 0.594,0.5 10 true Adjusting Value 1.865,0.51 2.208,0.729 0.344,0.219 10 true Bolt 2.51,0.5 3.104,0.917 0.594,0.417 10 true Set Bolt 3.958,0.5 4.896,0.906 0.938,0.406 10 true Adjusting Bolt 4.823,1.042 5.542,1.271 0.719,0.229 8 true 90105-17015 4.042,1.052 4.729,1.281 0.688,0.229 8 true 90105-17014 3.25,1.052 3.938,1.26 0.688,0.208 8 true 90105-17013 2.458,1.052 3.135,1.271 0.677,0.219 8 true 90105-17008



i.

Repeat the steps mentioned above. When temporarily installing the 2 nuts, replace 1 or 2 selected bolts.

HINT:

Replace 1 bolt at a time when replacing 2 bolts.