Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292157 ANTI-LOCK BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TERMINALS OF ECU  


SKID CONTROL ECU


U189315E02
3.375,0.135 3.656,0.333 0.281,0.198 10 false A22 0.104,0.042 1.927,0.24 1.823,0.198 10 false Skid Control ECU Side:

Symbols (Terminal No.) Terminal Description
GND2 (A22-1) Actuator pump motor ground
+BM (A22-2) Motor relay power supply
+BS (A22-3) Solenoid valve power supply
GND1 (A22-4) Skid control ECU ground
FL- (A22-5) Front LH wheel speed signal input
RL+ (A22-6) Rear LH wheel speed sensor power supply
RR+ (A22-8) Rear RH wheel speed sensor power supply
FR+ (A22-9) Front RH wheel speed sensor power supply
FR- (A22-10) Front RH wheel speed signal input
D/G (A22-11) Diagnosis output
GGND (A22-14)* Deceleration sensor ground
CANL (A22-15) CAN communication line L
FL+ (A22-16) Front LH wheel speed sensor power supply
RL- (A22-17) Rear LH wheel speed signal input
IG1 (A22-18) ECU power supply
RR- (A22-19) Rear RH wheel speed signal input
STP (A22-20) Stop light switch input
GL1 (A22-21)* Deceleration sensor signal input
SP1 (A22-23) Speed signal output for speedometer
VGS (A22-24)* Deceleration sensor power supply output
TS (A22-25) Sensor diagnosis check input
CANH (A22-26) CAN communication line H

*: for CVT


CHECK SKID CONTROL ECU


U189316E02
3.542,0.104 3.854,0.271 0.313,0.167 10 false A22 0.125,0.052 1.521,0.229 1.396,0.177 10 false Wire Harness Side:

a.

Disconnect the A22 ECU connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND2 (A22-1) - Body ground W-B - Body ground Actuator pump motor ground Always Below 1 Ω
+BM (A22-2) - Body ground B - Body ground Motor relay power supply Always 10 to 14 V
+BS (A22-3) - Body ground W - Body ground Solenoid valve power supply Always 10 to 14 V
GND1 (A22-4) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω
IG1 (A22-18) - Body ground B - Body ground ECU power supply Engine switch on (IG) 10 to 14 V
STP (A22-20) - Body ground L - Body ground Stop light switch input Stop light switch ON
Brake pedal depressed
8 to 14 V
STP (A22-20) - Body ground L - Body ground Stop light switch input Stop light switch OFF
Brake pedal released
Below 1.5 V
SP1 (A22-23) - Body ground V - Body ground Speedometer output Vehicle speed input Pulse generation (see waveform 1)

If the result is not as specified, there may be a malfunction on the wire harness side.



c.
F047510E04
2.938,1.479 3.281,1.677 0.344,0.198 10 false GND

Waveform 1 (Reference): Using an oscilloscope:

Item Condition
Tool setting 5 V/DIV., 50 ms./DIV.
Vehicle condition While driving at approximately 20 km/h (12 mph)

HINT:

As the vehicle speed (tire rotating speed) becomes faster, the cycle becomes shorter.




CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)


U189317E02
2.156,2.896 2.365,3.073 0.208,0.177 10 false 4D 2.896,4.375 3.104,4.552 0.208,0.177 10 false 4D

a.

Disconnect the 4D ECU connector.


b.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
PKB (4D-13) - Body ground V - Body ground Parking brake switch input Parking brake switch ON Below 1 Ω
PKB (4D-13) - Body ground V - Body ground Parking brake switch input Parking brake switch OFF 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the 4D ECU connector.


d.

Measure the voltage of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
PKB (4D-13) - Body ground V - Body ground Parking brake switch input Parking brake switch ON Below 1 V
PKB (4D-13) - Body ground V - Body ground Parking brake switch input Parking brake switch OFF 10 to 14 V

If the result is not as specified, there may be a malfunction in the main body ECU.