Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292157 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (When Using Intelligent Tester)


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Read the DTCs following the prompts on the intelligent tester screen. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.




CLEAR DTC (When Using Intelligent Tester)


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Operate the intelligent tester to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / DTC / Clear.



CHECK DTC (When not Using Intelligent Tester)


a.
H100769E17
2.073,1.814 2.410,1.980 0.338,0.166 10 TC 0.932,1.798 1.170,1.959 0.238,0.161 10 CG 1.596,0.965 1.088,1.798 false 2.163,1.793 1.787,1.348 false

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Turn the engine switch on (IG).


c.

Read DTCs from the ABS warning light on the combination meter.

HINT:

If the ABS warning light does not blink, perform the relevant troubleshooting procedures. The relevant troubleshooting procedures are instructed in the sections listed in the table below.

Section Title See procedure
ABS Warning Light does not Come ON (Click here)
TC and CG Terminal Circuit (Click here)



d.

Count the number of blinks of the ABS warning light.

HINT:
·

How to read DTCs:

Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.

·

If one code is detected:

The light repeats the same code after a pause of 4 seconds.

·

If multiple codes are detected:

The light outputs one code after another with a 2.5-second pause between each code. When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.





f.

After completing the check, disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3, and turn the engine switch off.

HINT:

If 2 or more malfunctions are detected at the same time, the lowest numbered DTC is displayed first.




CLEAR DTC (When not Using Intelligent Tester)


a.
H100769E17
2.073,1.814 2.410,1.980 0.338,0.166 10 TC 0.932,1.798 1.170,1.959 0.238,0.161 10 CG 1.596,0.965 1.088,1.798 false 2.163,1.793 1.787,1.348 false

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Turn the engine switch on (IG).


c.
C135697

Clear the DTCs stored in the skid control ECU by depressing the brake pedal 8 times or more within 5 seconds.


d.

Check that the warning light blinks in the normal system code pattern.


e.

Remove SST from the terminals of the DLC3.


f.

Turn the engine switch off.

HINT:

Clearing the DTCs cannot be performed by removing the battery cable or GAUGE NO. 1 fuse.




END OF DTC CHECK/CLEAR


a.

Turn the engine switch on (IG).


b.

Check that the ABS warning light goes off within approximately 3 seconds.


c.

Turn the engine switch off.