Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


SKID CONTROL ECU


U189396E02
1.531,0.979 1.76,1.146 0.229,0.167 10 false A9 0.094,0.031 1.75,0.25 1.656,0.219 10 false Skid Control ECU Side:

Symbols (Terminal No.) Terminal Description
GND2 (A9-1) Motor ground
+BM (A9-2) Motor relay input
+BS (A9-3) Solenoid valve power supply
GND1 (A9-4) Skid control ECU ground
FL- (A9-5) Front LH wheel speed signal input
RL+ (A9-6) Rear LH wheel speed sensor power supply
RR+ (A9-8) Rear RH wheel speed signal power supply
FR+ (A9-9) Front RH wheel speed sensor power supply
FR- (A9-10) Front RH wheel speed signal input
D/G (A9-11) Diagnosis output
STP2 (A9-13) Stop light control relay input
CANL (A9-14) CAN communication line L
TS (A9-16) Sensor diagnosis check input
CSW (A9-17) VSC OFF switch input
FSW+ (A9-20) Brake pedal load sensing switch input
FL+ (A9-26) Front LH wheel speed sensor power supply
RL- (A9-27) Rear LH wheel speed signal input
IG1 (A9-28) ECU power supply
RR- (A9-29) Rear RH wheel speed signal input
STP (A9-30) Stop light switch input
SP1 (A9-33) Speed signal output for combination meter
CANH (A9-35) CAN communication line H
STP0 (A9-39) Stop light control relay output


CHECK SKID CONTROL ECU


U189397E02
1.188,1.021 1.375,1.198 0.188,0.177 10 false A9 0.115,0 1.49,0.229 1.375,0.229 10 false Wire Harness Side:

a.

Disconnect the A9 ECU connector.


b.

Measure the voltage and resistance of the wire harness side connector.

HINT:

The voltage cannot be measured with the connector connected to the skid control ECU as the connector is water resistant.


Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND2 (A9-1) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω
+BS (A9-3) - Body ground W - Body ground Solenoid relay power supply Always 10 to 14 V
STP2 (A9-13) - Body ground L - Body ground Stop light control relay input Stop light switch OFF
Brake pedal released
Below 1.5 V
STP2 (A9-13) - Body ground L - Body ground Stop light control relay input Stop light switch ON
Brake pedal depressed
8 to 14 V
CSW (A9-17) - Body ground R - Body ground VSC OFF switch input VSC OFF switch held ON → OFF (Not pressed) Below 1 Ω → 10 kΩ or higher
FSW+ (A9-20) - Body ground Y - Body ground Brake pedal load sensing switch input Brake pedal load sensing switch ON
Brake pedal released
202.4 to 223.7 Ω
FSW+ (A9-20) - Body ground Y - Body ground Brake pedal load sensing switch input Brake pedal load sensing switch OFF
Brake pedal depressed
0.95 to 1.05 kΩ
IG1 (A9-28) - Body ground B - Body ground ECU power supply Engine switch on (IG) 10 to 14 V
STP (A9-30) - Body ground L - Body ground Stop light switch input Stop light switch OFF
Brake pedal released
Below 1.5 V
STP (A9-30) - Body ground L - Body ground Stop light switch input Stop light switch ON
Brake pedal depressed
8 to 14 V
STP0 (A9-39) - Body ground Y - Body ground Stop light control relay output Engine switch on (IG) 11 to 14 V



CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)


U189317E02
2.156,2.896 2.365,3.073 0.208,0.177 10 false 4D 2.896,4.375 3.104,4.552 0.208,0.177 10 false 4D

a.

Disconnect the 4D ECU connector.


b.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
PKB (4D-13) - Body ground V - Body ground Parking brake switch input Parking brake switch ON Below 1 Ω
PKB (4D-13) - Body ground V - Body ground Parking brake switch input Parking brake switch OFF 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the 4D ECU connector.


d.

Measure the voltage of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
PKB (4D-13) - Body ground V - Body ground Parking brake switch input Parking brake switch ON Below 1 V
PKB (4D-13) - Body ground V - Body ground Parking brake switch input Parking brake switch OFF 10 to 14 V

If the result is not as specified, the junction block LH (ECU) may be a malfunction.