Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1231/31  Steering Angle Sensor Circuit Malfunction  


DESCRIPTION

The steering angle sensor signal is sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor zero point malfunction diagnostic function.

DTC No. DTC Detection Condition Trouble Area
C1231/31 When IG1 terminal voltage 9.5 V or more, steering angle sensor malfunction signal received.
·

Steering angle sensor

·

Steering angle sensor circuit

·

Steering angle sensor power supply

·

CAN communication system



WIRING DIAGRAM

C137958E05
4.192,0.763 5.338,0.928 1.147,0.165 10 Skid Control ECU 5.63,1.115 6.091,1.271 0.461,0.156 10 CANH 5.63,2.058 6.091,2.214 0.461,0.156 10 CANH 6.338,1.115 6.799,1.271 0.461,0.156 10 CANL 6.338,2.068 6.799,2.224 0.461,0.156 10 CANL 5.479,2.647 5.681,2.849 0.202,0.202 10 IG 3.564,3.578 4.488,3.753 0.924,0.174 10 RH-IG Relay 1 2.902,3.274 3.280,3.449 0.377,0.175 10 IG1D 5.471,4.64 5.766,4.796 0.295,0.156 10 BAT 5.45,5.493 5.763,5.649 0.313,0.156 10 ESS 5.431,6.339 6.890,6.519 1.459,0.180 10 Steering Angle Sensor 4.476,2.795 5.248,2.951 0.772,0.156 10 RH ECU-IG 3.149,4.772 3.666,4.928 0.517,0.156 10 ECU-B 2.222,4.081 3.257,4.237 1.036,0.156 10 Main Body ECU 0.432,4.788 1.083,4.944 0.651,0.156 10 F/B BATT 0.465,5.068 1.065,5.224 0.600,0.156 10 FL MAIN 0.617,5.718 1.125,5.874 0.508,0.156 10 Battery 2.189,3.244 2.545,3.405 0.355,0.161 10 AM1 2.194,3.686 2.550,3.847 0.355,0.161 10 AM2 1.218,3.408 1.675,3.763 0.457,0.355 10 AM2 NO. 2 1.455,2.795 1.778,2.962 0.323,0.167 10 ALT 2.415,2.795 3.287,2.965 0.872,0.170 10 RH-MAIN-JB 4.192,0.608 4.417,0.785 0.225,0.177 10 A9 5.437,6.192 5.725,6.351 0.288,0.159 10 G18 5.254,2.519 5.410,2.709 0.156,0.191 10 1 1.95,3.495 2.106,3.685 0.156,0.191 10 1 1.929,3.079 2.085,3.270 0.156,0.191 10 6 5.261,4.515 5.417,4.706 0.156,0.191 10 3 3.416,3.081 3.572,3.272 0.156,0.191 10 3 5.261,5.37 5.417,5.560 0.156,0.191 10 2 1.835,3.682 2.218,3.852 0.383,0.170 10 G58 1.851,3.262 2.169,3.432 0.318,0.170 10 G57 3.32,3.261 3.638,3.431 0.318,0.170 10 G57 5.637,1.365 5.839,1.516 0.202,0.151 10 35 6.52,1.342 6.722,1.516 0.202,0.174 10 14 5.651,1.827 5.839,1.983 0.188,0.156 10 10 6.566,1.809 6.708,1.974 0.142,0.165 10 9

CAUTION / NOTICE / HINT

HINT:
·

When U0073/94 or U0123/62 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94 or U0123/62 first.

·

When there are problems with the speed sensor or the yaw rate sensor, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate sensor are output together with other DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate sensor first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.READ VALUE USING DATA LIST (MOMENTARY INTERRUPTION)
a.

Using the Data List of the intelligent tester, check for any momentary interruptions in the wire harness and connectors between the skid control ECU and the steering angle sensor (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Open Steering angle sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal
-

OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.CHECK DTC

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (STEERING ANGLE SENSOR TO SKID CONTROL ECU)
2.CHECK DTC

b.

Turn the engine switch off.


c.

Turn the engine switch on (IG) again and check that no CAN communication system DTC is output.


d.

Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (24 mph) and check that no speed and yaw rate sensor DTCs are output.

Result
Result Proceed to
No CAN communication system, speed sensor, or yaw rate sensor DTCs are output. A
CAN communication system DTC is output B
Speed sensor or yaw rate sensor DTC is output C



A

3.CHECK WIRE HARNESS (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

B

CHECK AND REPLACE CAN COMMUNICATION SYSTEM

C

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

3.CHECK WIRE HARNESS (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
U189015E02
1.042,1.417 0.865,1.74 false 1.198,1.427 1.198,1.74 false 1.375,1.417 1.615,1.74 false 0.188,0.115 1.552,0.26 1.365,0.146 10 false Wire Harness Side: 1.521,0.479 1.802,0.656 0.281,0.177 10 false G18 0.719,1.74 0.906,1.906 0.188,0.167 10 false IG 1.073,1.771 1.396,1.938 0.323,0.167 10 false ESS 1.646,1.75 1.969,1.917 0.323,0.167 10 false BAT

a.

Remove the steering wheel and the column cover.


b.

Disconnect the G18 sensor connector.


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
G18-1 (IG) - Body ground Engine switch on (IG) 10 to 14 V
G18-3 (BAT) - Body ground Always 10 to 14 V



d.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G18-2 (ESS) - Body ground Below 1Ω




OK

REPLACE STEERING ANGLE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (STEERING ANGLE SENSOR TO SKID CONTROL ECU)

NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle and turn the steering wheel to the right and left at a speed of 45 km/h (28 mph) or more for several seconds.


d.

Check if the same DTC is recorded (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

END

B

2.CHECK DTC