Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  SYSTEM DESCRIPTION  


FUNCTION DESCRIPTION


a.

Anti-lock Brake System (ABS)

i.

The ABS helps prevent the wheels from locking when the brakes are applied firmly or on a slippery surface.



b.

Electronic Brake Force Distribution (EBD)

i.

The EBD control utilizes the ABS to create the proper brake force distribution between the front and rear wheels in accordance with the driving conditions and vehicle load. In addition, when the brakes are applied while cornering, it also controls the braking forces of the right and left wheels, helping to maintain vehicle stability.



c.

Brake Assist (BA)

i.

The primary purpose of the brake assist system is to provide auxiliary brake force to assist drivers who cannot generate a large enough brake force during emergency braking, thus helping to maximize the vehicle's braking performance.



d.

Traction Control (TRC)

i.

The TRC system helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.



e.

Vehicle Stability Control (VSC)

i.

The VSC system helps prevent the vehicle from slipping sideways when front or rear wheel skidding occurs while cornering.




FUNCTION OF COMPONENTS


Component Function
ABS and TRACTION Actuator
·

Consists of the master cylinder cut solenoid valve, holding solenoid valve, pressure reduction solenoid valve, pump motor, and reservoir, and adjusts the brake fluid pressure applied to each wheel cylinder.

·

Houses the skid control ECU.


ABS and TRACTION Actuator Skid Control ECU
·

Processes the signals from each sensor to control the ABS, BA, TRC, and VSC.

·

Sends and receives control signals to and from the ECM, yaw rate sensor, steering angle sensor, etc. via CAN communication.


Skid Control ECU Solenoid Relay
·

Supplies power to each solenoid.

·

Housed in the skid control ECU.


Master Cylinder Pressure Sensor
·

Detects the brake fluid pressure in the master cylinder.

·

Housed in the ABS and TRACTION actuator.


Speed Sensor Detects the wheel speed and sends the signal to skid control ECU.
VSC OFF Switch Enables the driver to select the normal mode, TRC off mode or VSC off mode.
Stop light control (BRK-LP) relay Turns on the stop lights during hill-start assist control operation.
Steering Angle Sensor
·

Detects the steering extent and direction and sends signals to the skid control ECU via CAN communication.

·

Has a magnetic resistance element which detects the rotation of the magnet housed in the detection gear in order to detect the changes in magnetic resistance and the steering amount and direction.


Yaw Rate Sensor
·

Yaw rate sensor detects the vehicle's angular velocity (yaw rate) in the vertical direction based on the extent and direction of the deflection of the piezoelectric ceramics.

·

Deceleration sensor measures the capacity of the condenser that changes the distance between the electrodes depending on G force, which occurs when the vehicle is accelerated, and converts the measured value into electrical signals.

·

Sends signals to the skid control ECU via CAN communication.


ECM Controls the engine output when TRC and VSC are operating with the skid control ECU via CAN communication.
Combination Meter ABS Warning Light Illuminates to inform the driver that a malfunction in the ABS has occurred.
Brake Warning light
·

Illuminates to inform the driver that the parking brake is applied when the system is normal, and when the brake fluid has decreased.

·

Illuminates to inform the driver that a malfunction in the EBD has occurred.


Slip Indicator Light
·

Blinks to inform the driver that TRC, VSC and hill-start assist control are operating.

·

Illuminates to inform the driver that a malfunction has occurred in the TRC or VSC system.


TRC OFF Indicator Light Illuminates to inform the driver when TRC off mode or VSC off mode is selected.
VSC OFF Indicator Light Illuminates to inform the driver when VSC off mode is selected.