Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed.

Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light / ON or OFF ON: Warning light on
OFF: Warning light off
-
Brake Warning Light Brake warning light / ON or OFF ON: Warning light on
OFF: Warning light off
-
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch assembly / ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Main Idle SW Main idle switch / ON or OFF ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-
Gear Position Gear position information / P, N, R, 1st-8th, Fail or Not R Actual gear position -
Shift Lever Position Shift lever position information / "P,N", R, D/M, 1st-6th/B or Fail Actual shift lever position -
Shift Information Shift information / ON or OFF ON: During gear change -
Inspection Mode Inspection mode / Other or Inspect Other: Normal mode
Inspect: Inspection mode
-
Number of IG ON(Inspection) Number of times engine switch turned on (IG) after entering inspection mode / Min.: 0, Max.: 255 - -
Master Cylinder Sensor Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.20 to 0.40 V Reading increases when brake pedal is depressed
Deceleration Sensor Acceleration sensor reading / Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele Memorized zero value / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Deceleration Sensor2 Acceleration sensor 2 reading / Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele2 Memorized zero value / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Yaw Rate Sensor Yaw rate sensor / Min.: -128°/s, Max.: 127°/s Vehicle stopped: 0 °/s
Turning right: -128 to 0 °/s
Turning left: 0 to 127 °/s
-
Zero Point of Yaw Rate Memorized zero value / Min.: -128°/s, Max.: 127°/s - After completing zero point calibration: 0°
Steering Angle Sensor Steering angle sensor / Min.: -3276.8°, Max.: 3276.7° Turning left: Increases
Turning right: Decreases
-
Zero Point of Steering Angle Memorized zero value / Min.: -3276.8°, Max.: 3276.7° - After steering angle sensor zero point calibration: 0°
Lateral G Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Value Yaw rate value / Min.: -128°/s, Max.: 127°/s - During turning: Changes in proportion with yaw
Steering Angle Value Steering angle value / Min.: -3276.8°, Max.: 3276.7° - During steering operation: Changes in proportion with steering wheel rotation
Slip Indicator Light Slip indicator light / ON or OFF ON: Indicator light on
OFF: Indicator light off
-
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FR Wheel Acceleration Front wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
FL Wheel Acceleration Front wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
RR Wheel Acceleration Rear wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
RL Wheel Acceleration Rear wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
FR Wheel ABS Ctrl Status Front wheel RH ABS control status / ON or OFF ON: During control -
FL Wheel ABS Ctrl Status Front wheel LH ABS control status / ON or OFF ON: During control -
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status / ON or OFF ON: During control -
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status / ON or OFF ON: During control -
FR Wheel EBD Ctrl Status Front wheel RH EBD control status / ON or OFF ON: During control -
FL Wheel EBD Ctrl Status Front wheel LH EBD control status / ON or OFF ON: During control -
RR Wheel EBD Ctrl Status Rear wheel RH EBD control status / ON or OFF ON: During control -
RL Wheel EBD Ctrl Status Rear wheel LH EBD control status / ON or OFF ON: During control -
BA Ctrl Status BA control status / ON or OFF ON: During control -
TRC(TRAC) Ctrl Status TRC control status / ON or OFF ON: During control -
TRC(TRAC) Engine Ctrl Status TRC engine control status / ON or OFF ON: During control -
TRC(TRAC) Brake Ctrl Status TRC brake control status / ON or OFF ON: During control -
FR Wheel VSC Ctrl Status Front wheel RH VSC control status / ON or OFF ON: During control -
FL Wheel VSC Ctrl Status Front wheel LH VSC control status / ON or OFF ON: During control -
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status / ON or OFF ON: During control -
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status / ON or OFF ON: During control -
Engine Revolutions Engine speed / Min.: 0 rpm, Max.: 65535 rpm Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
Real Engine Torque Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm - -
Accelerator Opening Angle % Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 128.0% Accelerator pedal released: 0% During accelerator pedal operation: Changes in proportion with the pedal movement
Solenoid Relay ABS solenoid relay / ON or OFF ON: Solenoid relay on
OFF: Solenoid relay off
-
ECB Motor Relay ABS motor relay / ON or OFF ON: Motor relay on
OFF: Motor relay off
ECB: Electronically Controlled Brake
TR(A)C/VSC Solenoid (SRM2) Master cut solenoid (SRM2) / ON or OFF ON: During control -
TR(A)C/VSC Solenoid (SRM1) Master cut solenoid (SRM1) / ON or OFF ON: During control -
TR(A)C/VSC Solenoid (SRC2) Master cut solenoid (SRC2) / ON or OFF ON: During control -
TR(A)C/VSC Solenoid (SRC1) Master cut solenoid (SRC1) / ON or OFF ON: During control -
ABS Solenoid (SFRH) ABS solenoid (SFRH) / ON or OFF ON: During control -
ABS Solenoid (SFRR) ABS solenoid (SFRR) / ON or OFF ON: During control -
ABS Solenoid (SFLH) ABS solenoid (SFLH) / ON or OFF ON: During control -
ABS Solenoid (SFLR) ABS solenoid (SFLR) / ON or OFF ON: During control -
ABS Solenoid (SRRH) ABS solenoid (SRRH) / ON or OFF ON: During control -
ABS Solenoid (SRRR) ABS solenoid (SRRR) / ON or OFF ON: During control -
ABS Solenoid (SRLH) ABS solenoid (SRLH) / ON or OFF ON: During control -
ABS Solenoid (SRLR) ABS solenoid (SRLR) / ON or OFF ON: During control -
EFI Communication Open ECM communication open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Yaw Rate Open Yaw rate sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Deceleration Open Acceleration sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Steering Open Steering angle sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
IG1 Voltage Value IG1 voltage value / Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
BS1 Voltage Value +BS voltage value / Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
MT Voltage Value Motor voltage value / Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
TRC/VSC Off Mode TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
Unknown: Unspecified
VSC OFF: VSC off mode
-
Number of DTC Number of DTC recorded / Min.: 0, Max.: 255 - -
IG Voltage Value Decreased +BS voltage value decrease detection / Error or Normal Error: Voltage low
Normal: Normal
-
IG Voltage Value Increased +BS voltage value increase detection / Error or Normal Error: Voltage high
Normal: Normal
-



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed.

Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


g.

According to the display on the GTS, perform the Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe combination meter assembly
Brake Warning Light Brake warning light Warning light ON/OFF Observe combination meter assembly
Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard
ABS Solenoid (SRLR) ABS solenoid (SRLR) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SRLH) ABS solenoid (SRLH) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SRRR) ABS Solenoid (SRRR) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SRRH) ABS solenoid (SRRH) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFLR) ABS solenoid (SFLR) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFLH) ABS solenoid (SFLH) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFRR) ABS solenoid (SFRR) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFRH) ABS solenoid (SFRH) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
VSC/TRC Solenoid (SRMR) Master cut solenoid (SRM2) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
VSC/TRC Solenoid (SRMF) Master cut solenoid (SRM1) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
VSC/TRC Solenoid (SRCR) Master cut solenoid (SRC2) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
VSC/TRC Solenoid (SRCF) Master cut solenoid (SRC1) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
TRC(TRAC) OFF Indicator Light TRC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Slip Indicator Light Slip indicator light Indicator light ON/OFF Observe combination meter assembly
ABS Solenoid ABS solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR, SFRH) Solenoid SRLR/SRLH/SRRR/ SRRH/SFLR/SFLH/SFRR/SFRH Operation sound of solenoid (clicking sound) can be heard
VSC/TRC(TRAC) Solenoid Master cut solenoid (SRM1, SRM2, SRC1, SRC2) Solenoid SRMF/SRMR/SRCF/ SRCR/SMF/SMR/SPFR/SPFL Operation sound of solenoid (clicking sound) can be heard