Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


HINT:
·

Whenever a DTC is detected or the ABS operates, the skid control ECU stores the current vehicle (sensor) state as freeze frame data.

·

The skid control ECU stores the number of times (maximum: 31) the engine switch has been turned from off to on (IG) since the last time the ABS was activated. However, if the vehicle was stationary or running at a low speed (7 km/h [4.3 mph] or less), or if a DTC is detected, the skid control ECU stops counting.

·

Freeze frame data at the time the ABS operates:

The skid control ECU stores and updates the data whenever the ABS system operates.

When the ECU stores data at the time a DTC is detected, the data stored when the ABS operated is erased.

·

Freeze frame data at the time a DTC is detected:

When the skid control ECU stores data at the time a DTC is detected, no updates will be performed until the data is cleared.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / DTC.


e.

Select a DTC to display its Freeze Frame Data.

ABS/VSC/TRC
Tester Display Measurement Item Reference Values
Elapsed Time after Freeze Trigger Elapsed time after freeze frame data recorded Min.: 0 ms
Max.: 500 ms
Number of IG ON Number of engine switch on (IG) operations since freeze frame data stored 1 to 31
Buzzer Buzzer signal ON: Buzzer ON
OFF: Buzzer OFF
Stop Light SW Stop light switch signal ON: Stop light switch ON
OFF: Stop light switch OFF
Parking Brake SW Parking brake switch signal ON: Parking brake switch ON
OFF: Parking brake switch OFF
Brake Pedal Load Sensing SW Brake pedal load sensing switch signal ON: Brake pedal depressed
OFF: Brake pedal released
Gear Position Gear position information FAIL
1st
2nd
3rd
4th
5th
6th
P, N
R
NOT R
Shift Lever Position Shift lever position information FAIL
1st
2nd
3rd
4th
5th
6th/B
D/M
P, N
R
Operated System Operated system status ABS: ABS activated
VSC: VSC activated
TRC: TRC activated
FAIL: Fail safe mode activated
SYS: System prohibited
NON: No system activated
Master Cylinder Sensor Master cylinder pressure sensor reading Brake pedal released: 0.3 V to 0.9 V
Brake pedal depressed: 0.8 V to 4.5 V
M/C Sensor Grade Master cylinder pressure sensor change Min.: -30 MPa/s
Max.: 225 MPa/s
Yaw Rate Sensor Yaw rate sensor reading Min.: -128 deg/s
Max.: 127 deg/s
Steering Angle Sensor Steering angle sensor reading Left turn: Increase
Right turn: Decrease
Lateral G Lateral G Min.: -25.11 m/s2
Max.: 24.91 m/s2
Forward and Rearward G Forward and backward G Min.: -25.11 m/s2
Max.: 24.91 m/s2
FR Wheel Speed FR wheel speed Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
FL Wheel Speed FL wheel speed Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
RR Wheel Speed RR wheel speed Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
RL Wheel Speed RL wheel speed Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
Vehicle Speed Grade Vehicle speed grade Min.: -25.11 m/s2
Max.: 24.91 m/s2
Real Engine Torque Real engine torque Min.: -1024 Nm
Max.: 1023 Nm
Accelerator Opening Angle % Accelerator pedal opening angle % Min.: 0%
Max.: 128%
Inspection Mode Inspection mode OTHER: Normal
INSPECT: Service
TRC/VSC Off Mode TRC/VSC off mode Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode