FREEZE FRAME DATA
Whenever an ABS DTC is detected, the skid control ECU (brake actuator assembly) stores the current vehicle (ECU or sensor) state as Freeze Frame Data.
The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the engine switch has been turned from off to on (IG) since the last time the ABS was activated.
If the vehicle is stopped or driven at a low speed (7 km/h (4.3 mph) or less), or if a DTC is detected, the skid control ECU (brake actuator assembly) will stop counting the number.
Freeze Frame Data at the time the ABS operates:
The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS operates.
When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is cleared.
Freeze Frame Data at the time a DTC is detected:
When the skid control ECU (brake actuator assembly) stores data at the time a DTC is detected, no updates will be performed until the data is cleared.
CHECK FREEZE FRAME DATA
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Select a DTC to display its Freeze Frame Data.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Elapsed Time after Freeze Trigger | Elapsed time after freeze trigger / Min.: 0 msec, Max.: 500 msec | - | - |
| Number of IG ON | Number of times engine switch turned on (IG) after Freeze Frame Data stored / 0 to 31 | - | - |
| Stop Light SW | Stop light switch assembly / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Parking Brake SW | Parking brake switch assembly / ON or OFF | ON: Parking brake applied
OFF: Parking brake released |
- |
| Gear Position | Gear position information / P, N, R, 1st-8th, Fail or Not R | Actual gear position | - |
| Shift Lever Position | Shift lever position information / P/N, R, D/M, 1st-6th/B or Fail | Actual shift lever position | - |
| Operated System | Operated system status / BS, VSC, TRC, BA, HAB, PBA, PB, HA-CTRL, TSC, Fail, Sys or Non | Actual operated system | ABS: ABS activated.
VSC: VSC activated. TRC: TRC activated. BA: BA activated. HAB: High power assist brake activated. PBA: PBA activated.* PB: PB activated.* HA-CTRL: Hill-start assist control activated. TSC: Trailer sway control activated* Fail: Fail-safe mode activated. Sys: System prohibit activated. Non: No operation activated. |
| Master Cylinder Sensor | Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.20 to 0.40 V | Reading increases when brake pedal is depressed |
| M/C Sensor Grade | Master cylinder pressure sensor change / Min.: -30 MPa/s, Max.: 225 MPa/s | Brake pedal released or pedal held at constant position: 0 MPa/s | When brake pedal is being operated: Changes in proportion with the pedal movement speed |
| Yaw Rate Sensor | Yaw rate sensor / Min.: -128°/s, Max.: 127°/s | Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Lateral G | Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2 | - | During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and backward G / Min.: - 25.10 m/s2, Max.: 24.90 m/s2 | - | During acceleration/deceleration: Changes in proportion with acceleration |
| FR Wheel Speed | Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed | Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed Grade | Vehicle speed grade / Min.: -25.10 m/s2, Max.: 24.90 m/s2 | Vehicle stopped: 0 m/s2 | During driving: Changes in proportion with vehicle acceleration/deceleration |
| Real Engine Torque | Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm | - | - |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 128.0% | The accelerator pedal released: 0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch / ON or OFF | ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point |
- |
| Inspection Mode | Inspection mode / Other or Inspect | Other: Normal mode
Inspect: Inspection mode |
- |
| Steering Angle Sensor | Steering angle sensor / Min.: - 3276.8°, Max.: 3276.7° | Turning left: Increase
Turning right: Decrease |
- |
| TRC/VSC Off Mode | TRC/VSC off mode / Normal, TRC OFF or VSC OFF | Normal: Normal mode
TRC OFF: TRC off mode VSC OFF: VSC off mode |
- |
*: Not supported
CLEAR FREEZE FRAME DATA
Clearing the DTCs will also clear the Freeze Frame Data.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Clear the DTCs and Freeze Frame Data (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).