The skid control ECU (brake actuator assembly) receives signals from the ECM, steering angle sensor and yaw rate and acceleration sensor via CAN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U0073 | Control Module Communication Bus OFF | The +BS terminal voltage is between 9.6 and a 16.5 V and a bus OFF state occurs for 0.1 seconds or more. | CAN communication system |
| U0100 | Lost Communication with ECM / PCM | The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the ECM for 2 seconds or more. | ·
CAN communication system ·
Skid control ECU (brake actuator assembly) ·
ECM |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the yaw rate sensor cannot be received for 1 second or more. | ·
CAN communication system ·
Skid control ECU (brake actuator assembly) ·
Yaw rate sensor (yaw rate and acceleration sensor) |
| U0126 | Lost Communication with Steering Angle Sensor Module | The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the steering angle sensor cannot be received for 1 second or more. | ·
CAN communication system ·
Skid control ECU (brake actuator assembly) ·
Steering angle sensor |
When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| EFI Communication Open | ECM communication open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Yaw Rate Open | Yaw rate sensor open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Deceleration Open | Acceleration sensor open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Steering Open | Steering angle sensor open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Result | Proceed to |
|---|---|
| There is a constant interruption. (Error is displayed without interruption.) | A |
| There are no momentary interruptions. | B |
| There are momentary interruptions. (Error is displayed intermittently.) | C |
Perform the above inspection before disconnecting any sensors or connectors.
A
B
C
Turn the engine switch off.
Check if each sensor or ECM connector is securely connected.
Each connector is securely connected.
OK
NG
Turn the engine switch off.
Record the output DTCs (for VSC system and/or CAN communication system) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR for VSC system and/or Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM for CAN communication system).
If CAN communication system DTCs and related sensor DTCs are output simultaneously, troubleshoot the DTCs (for VSC system) after the CAN communication system returns to normal.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
| CAN communication system DTCs are output. | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Turn the engine switch off.
Repair or replace the harness or connector.
Check for any momentary interruptions between the skid control ECU (brake actuator assembly) and each sensor or ECM (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
NEXT
Turn the engine switch off.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.
Check that no CAN communication system DTCs are output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
If VSC system DTCs are output, record them (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
| CAN communication system DTCs are output. | C |
A
B
C