WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK
Release the parking brake.
Before releasing the parking brake, move the shift lever to P.
When the parking brake is applied or the brake fluid level is low, the brake warning light comes on.
When the engine switch is turned on (IG), check that the ABS warning, brake warning, slip indicator, TRC OFF indicator and VSC OFF indicator lights all come on for approximately 3 seconds.
If the skid control ECU (brake actuator assembly) stores a DTC, the ABS warning and slip indicator lights will come on.
If any of the indicators remains on or does not come on, proceed to troubleshooting for the light circuits listed below.
SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using GTS)
Perform Test Mode with the vehicle stopped.
DTCs are stored if any malfunctions are detected during the check of each sensor.
Procedure to enter Test Mode
Turn the engine switch off.
Check that the steering wheel is centered.
Check that the shift lever is in P.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Switch the skid control ECU (brake actuator assembly) to Test Mode using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode pattern. The TRC OFF indicator light comes on during Test Mode.
If the ABS warning and slip indicator lights do not blink, inspect the ABS warning and slip indicator light circuits.
If the TRC OFF indicator light does not come on, inspect the TRC OFF indicator light circuit.
Check the ABS sensors.
Check that the ABS warning light is blinking in the Test Mode pattern before performing the following ABS sensor checks.
VSC OFF Switch Check (for LHD)
Press the VSC OFF Switch.
Check that the VSC OFF indicator light comes on.
Press the VSC OFF Switch again.
VSC OFF Switch (combination switch assembly) Check (for RHD)
Press the VSC OFF Switch (combination switch assembly).
Check that the VSC OFF indicator light comes on.
Press the VSC OFF Switch (combination switch assembly) again.
Lost Booster Pressure Judgment Check
Perform the check in the lost booster pressure state (vacuum in the booster is released by pumping the brake pedal).
Turn the engine switch on (IG).
Check that the brake warning light comes on when depressing the brake pedal with a force of 74.0 N (7.5 kgf, 16.6 lbf) or more for 1 second or more. (The lost booster pressure state is judged to be normal.)
Start the engine while depressing the brake pedal with a force of 74.0 N (7.5 kgf, 16.6 lbf) or more for 1 second or more.
Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged to be normal.)
If the lost booster pressure judgment check does not complete normally, the speed sensor check will not be performed.
If a recheck is performed after the engine has been started, end Test Mode, enter Test Mode again, and release the vacuum in the booster by pumping the brake pedal prior to the recheck.
If the lost booster pressure state is not judged to be normal, the brake warning light comes on and Test Mode DTC C1281 (Master Cylinder Pressure Sensor Output Malfunction) is stored.
Speed Sensor Check
Drive the vehicle straight-ahead. Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.
The speed sensor check may not complete if wheelspin occurs.
The speed sensor check may not complete if the speed sensor check is started while turning the steering wheel.
After the ABS warning light goes off, if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
Check that the ABS warning light goes off.
The ABS warning light goes off when the sensor check has completed.
The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.
Stop the vehicle.
When the sensor check has completed, the ABS warning light goes off while the vehicle is being driven, and blinks in the Test Mode pattern while the vehicle is stopped.
If the sensor check has not completed, the ABS warning light will blink while the vehicle is being driven and the ABS will not operate.
End of Sensor Check
If the sensor checks have completed, the ABS warning light blinks in the Test Mode pattern when the vehicle is stopped and the ABS warning light goes off while the vehicle is being driven.
If the sensor checks have not completed, the ABS warning light will blink while the vehicle is being driven and the ABS will not operate.
Reading Sensor Check DTCs
Read the DTCs by following the GTS screen.
If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunctions and clear the DTCs.
If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform Test Mode inspection again.
See "Sensor Check DTCs".
Turn the engine switch off and disconnect the GTS.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Areas |
|---|---|---|
| C1271 | Low Output Signal of Front Speed Sensor RH | ·
Front speed sensor RH ·
Sensor installation ·
Front speed sensor rotor RH (front axle hub sub-assembly RH) |
| C1272 | Low Output Signal of Front Speed Sensor LH | ·
Front speed sensor LH ·
Sensor installation ·
Front speed sensor rotor LH (front axle hub sub-assembly LH) |
| C1273 | Low Output Signal of Rear Speed Sensor RH | ·
Rear speed sensor RH ·
Sensor installation ·
Rear speed sensor rotor RH (rear axle hub and bearing assembly RH) |
| C1274 | Low Output Signal of Rear Speed Sensor LH | ·
Rear speed sensor LH ·
Sensor installation ·
Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH | Front speed sensor rotor RH (front axle hub sub-assembly RH) |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH | Front speed sensor rotor LH (front axle hub sub-assembly LH) |
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Rear speed sensor rotor RH (rear axle hub and bearing assembly RH) |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
| C1281 | Master Cylinder Pressure Sensor Output Malfunction | ·
Stop light switch assembly ·
Brake pedal load sensing switch (brake pedal support assembly) ·
Brake booster assembly ·
Master cylinder pressure sensor (brake actuator assembly) |
The codes in this table are output only in Test Mode (signal check).