Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) receives a +B line open signal from the steering angle sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1432 Steering Angle Sensor Power Source Voltage Malfunction With the +BS terminal voltage between 9.6 and 16.5 V, a steering angle sensor power supply circuit malfunction signal is received from the steering angle sensor.
·

Steering angle sensor power supply

·

Steering angle sensor



CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
G102541E01
0.333,0.583 0.75,0.833 0.417,0.25 0.74,1.771 0.948,1.406 false 1.521,1.813 1.344,1.406 false 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 0.406,0.615 0.719,0.813 0.313,0.198 10 false G18 0.635,1.792 0.948,1.99 0.313,0.198 10 false IG 1.448,1.833 1.76,2.031 0.313,0.198 10 false BAT

Remove the steering wheel and column cover.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the G18 steering angle sensor connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G18-3 (BAT) - Body ground Always 11 to 14 V
G18-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)



OK

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
G102541E02
0.333,0.583 0.75,0.833 0.417,0.25 1.354,1.813 1.177,1.406 false 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 0.406,0.615 0.719,0.813 0.313,0.198 10 false G18 1.344,1.833 1.656,2.031 0.313,0.198 10 false ESS

Turn the engine switch off.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Before measuring the resistance of the steering angle sensor, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.


Standard Resistance:
Tester Connection Condition Specified Condition
G18-2 (ESS) - Body ground 1 minute after engine switch off Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)