Home › Vehicle Interior › AIR CONDITIONING › FRONT COOLING UNIT
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292172 FRONT COOLING UNIT A

AIR CONDITIONING  FRONT COOLING UNIT  REASSEMBLY  


PROCEDURE

Hide 88625 1.INSTALL EVAPORATOR TEMPERATURE SENSOR

NOTICE:

If reusing the evaporator, do not insert the sensor to a location where the sensor was previously inserted. Insert the sensor within range C shown in the illustration.


a.
E360175E01
0.146,2.438 0.719,2.885 0.573,0.448 10 false 50 mm (1.96 in.) 0.969,3.073 1.521,3.427 0.552,0.354 10 false 34.3 mm (1.35 in.) 1.042,1.042 1.344,1.292 0.302,0.25 10 false C

Install the sensor as shown in the illustration.


Hide 88501 2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

C129881E01
1.739,1.862 2.224,2.046 0.485,0.184 10 O-Ring 2.61,1.839 2.518,1.976 2.518,1.976 2.306,1.976 false 2.598,1.701 2.43,1.971 false

a.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

Compressor oil:

ND-OIL 8 or equivalent



b.

Install the 2 O-rings to the cooler evaporator.


c.
C129878

Install the cooler evaporator with cooler thermistor to the air conditioning unit.


d.

Connect the clamp.


e.
E132086

Attach the 4 claws to install the plate cover.


f.

Install the 6 screws.


Hide 88515 3.INSTALL COOLER EXPANSION VALVE

C129879

a.

Install the cooler expansion valve.


b.

Using a 4 mm hexagon wrench, install the 2 hexagon bolts.

Torque:
3.5 N*m (35 kgf*cm, 30 in.*lbf)


Hide 87107A 4.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

E128528

a.

Install the heater radiator to the air conditioning unit.


b.
E132085

Install the clamp with the screw.


c.

Attach the 4 claws to install the heater clamp.


Hide 87106V 5.INSTALL NO. 2 AIR MIX DAMPER SERVO SUB-ASSEMBLY

a.
E221052E04
2.281,0.271 0.927,0.698 true 2.333,0.167 2.969,0.615 0.635,0.448 10 false Standard Position

Set the No. 2 air mix damper servo sub-assembly to the standard position shown in the illustration, and then install it with the 2 screws.


b.

Connect the connector.


Hide 87106L 6.INSTALL DAMPER SERVO SUB-ASSEMBLY

a.
E219269

Check that the slots, links and gears of the damper servo sub-assembly are positioned in the correct orientation as shown in the illustration.


b.

Face the contact surfaces of the damper servo sub-assembly and air conditioning unit for the damper servo sub-assembly upward.


c.

Rotate the link of the air conditioning unit all the way to the left as shown in the illustration.

E219270


d.

Rotate the link of the air conditioning unit to the bottom as shown in the illustration and confirm that the mode switching duct hole is fully closed.

E219271E01
0.347,1.382 1.427,2.029 1.079,0.647 10 Mode Switching Duct Hole 1.379,1.459 1.55,1.459 1.55,1.459 1.741,2.391 false


e.

Rotate the lever of the air conditioning unit to the bottom as shown in the illustration.

E219272


f.

Rotate the link of the air conditioning unit to the in-line position as shown in the illustration.

E220373E16
5.344,0.354 4.948,0.271 false 3.99,0.198 4.99,0.448 1,0.25 10 true In-line Position


g.
E219274E13
1.5,1.146 2.063,1.146 true 2.104,1.052 2.938,1.396 0.833,0.344 10 true Vinyl Tape

Wrap the upper and lower links with vinyl tape to hold them in the in-line position.


h.

Install the link of the damper servo sub-assembly to the link guide pin (A) of the air conditioning unit as shown in the illustration.

E219275E09
3.219,0.26 3.365,0.26 3.365,0.26 3.573,0.563 true 1.292,1.427 0.906,1.427 0.906,1.427 1.115,2.667 true 1.458,2.625 1.115,3.729 true 5.74,1.51 5.885,1.51 5.885,1.51 6.26,2.865 true 6.5,2.979 5.917,3.76 true 2.813,0.177 3.281,0.438 0.469,0.26 10 false Guide 0.167,3.76 2.125,3.938 1.958,0.177 10 false Damper Servo Sub-assembly 1.333,1.344 2.552,1.667 1.219,0.323 10 false Link Guide Pin (A) 4.594,1.417 5.802,1.781 1.208,0.365 10 false Link Guide Pin (B) 4.865,3.781 7.125,4.083 2.26,0.302 10 false Damper Servo Sub-assembly Slot


i.

Install the guide hole of the damper servo sub-assembly to the guide pin of the air conditioning unit as shown in the illustration.


j.

Temporarily install the screw (up to 4 or 5 threads).

NOTICE:
·

Make sure that the link guide pin (B) is inserted in the damper servo sub-assembly slot.

·

Avoid tilting the damper servo sub-assembly during installation. This helps to prevent the guide pins from coming out of position.




k.
E219276

Lift the damper servo sub-assembly slightly to create clearance.


l.

Move the air conditioning unit gear so that alignment holes of the damper servo sub-assembly and air conditioning unit are aligned.

E219277E23
2.292,0.833 3.333,1.24 true 1.531,2.271 1.323,2.271 1.323,2.271 1.604,3.073 true 2.094,3.469 1.979,3.469 1.979,3.469 1.823,3.135 true 0.406,0.75 2.229,1.302 1.823,0.552 10 false Damper Servo Sub-assembly Alignment Hole 1.552,2.198 3.969,2.531 2.417,0.333 10 true Air Conditioning Unit Alignment Hole 2.146,3.375 4.844,3.625 2.698,0.25 10 true Air Conditioning Unit Gear Alignment Hole


m.
E219278

Insert a screwdriver into the aligned holes as shown in the illustration.


n.

Make sure that all the links and gears are in the positions shown in the illustration.

E219279E08
1.188,1.917 0.813,2.396 true 4.354,0.438 4.563,0.438 4.563,0.438 4.896,1.385 true 5.948,0.156 6.167,0.156 6.167,0.156 6.104,0.969 true 5.219,2.5 4.854,3.25 true 6.313,1.458 6.219,3.792 6.219,3.792 5.844,2.188 true 6.052,2.219 6.219,3.792 true 3.865,3.979 4.292,4.177 false 1.333,3.177 1.646,3.177 1.646,3.177 1.031,4.958 true 4.125,0.073 6.073,0.385 1.948,0.313 10 false Link is positioned to left side. 2.75,0.365 4.448,0.604 1.698,0.24 10 false Link guide pin is inserted. 4.01,3.271 5.875,3.5 1.865,0.229 10 false Link is positioned at bottom. 5.448,3.833 7.021,4.823 1.573,0.99 10 false Each link guide pin is inserted in its damper servo sub-assembly slot. 0.115,2.417 1.604,3.01 1.49,0.594 10 false Screwdriver is inserted into alignment holes. 0.115,3.094 1.354,3.75 1.24,0.656 10 false Lever is positioned at bottom. 3.292,3.896 3.885,4.385 0.594,0.49 10 true Links are in-line.


o.
E219280

Push the loose fitting damper servo sub-assembly into position.

NOTICE:
·

Make sure that the damper servo sub-assembly is fully pushed into position.

·

After pushing the servo into position, keep it in place by holding it until the screws are installed.



HINT:

Push the damper servo sub-assembly until a click sound is heard.



p.

Remove the screwdriver.


q.
E220478

Fully install the top screw, and then install the damper servo sub-assembly with the 2 remaining screws.


r.

Remove the vinyl tape.


s.
E220355

Connect the 2 connectors.


Hide 87710G 7.INSTALL PTC HEATER ASSEMBLY (for Cold Area)

E131503

a.

Install the PTC heater with the 2 screws.


Hide 88539K 8.INSTALL DRAIN COOLER HOSE

E133857

a.

Install the drain hose to the air conditioning unit.