CHECK AIR CONDITIONING AMPLIFIER
Measure the voltage of the connectors.
Check from the rear of the connector while it is connected to the air conditioning amplifier.
| Symbol (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| IG+ (G47-1) - GND (G47-14) | B - W-B | Power source (IG) | Engine switch on (IG) | 10 to 14 V |
| SOL+ (G47-2) - GND (G47-14) | W - W-B | A/C compressor operation signal | Engine idling | Pulse generation
(see waveform 1) |
| Blower switch LO | ||||
| A/C switch ON | ||||
| PTC1 (G47-3) - Body ground (*1) | R - Body ground | PTC No. 1 heater relay operation signal | Engine idling | Below 1 V → 10 to 14 V |
| Set temperature: MAX HOT | ||||
| Engine coolant temperature: Below 65°C (149°F) | ||||
| Ambient temperature: Below 10°C (50°F) | ||||
| Blower switch OFF → LO | ||||
| PTC3 (G47-4) - Body ground (*1) | V - Body ground | PTC No. 3 heater relay operation signal | Engine idling | Below 1 V → 10 to 14 V |
| Set temperature: MAX HOT | ||||
| Engine coolant temperature: Below 65°C (149°F) | ||||
| Ambient temperature: Below 10°C (50°F) | ||||
| Blower switch OFF → LO | ||||
| TAM (G47-5) - GND (G47-14) | L - W-B | Ambient temperature sensor signal | Engine switch on (IG) | 1.8 to 2.2 V |
| Ambient temperature: 25°C (77°F) | ||||
| LOCK (G47-8) - GND (G47-14) (*4) | V - W-B | A/C lock sensor signal | Engine idling | Pulse generation
(see waveform 5) |
| A/C switch ON | ||||
| Blower switch LO | ||||
| PRE (G47-9) - SG-2 (G47-13) | GR - G | Air conditioning pressure sensor signal | Refrigerant pressure: Normal | 0.76 to 4.74 V |
| PRE (G47-9) - SG-2 (G47-13) | GR - G | Air conditioning pressure sensor signal | Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi]) | Below 0.76 V |
| PRE (G47-9) - SG-2 (G47-13) | GR - G | Air conditioning pressure sensor signal | Refrigerant pressure: Abnormal (more than 3.14 MPa [32 kgf/cm2, 455 psi]) | 4.74 V or higher |
| S5-3 (G47-10) - GND (G47-14) | B - W-B | Power supply for pressure sensor | Engine switch on (IG) | 4.5 to 5.5 V |
| CANH (G47-11) - GND (G47-14) | V - W-B | Hi-level CAN bus line | Engine switch on (IG) | Pulse generation
(see waveform 3) |
| CANL (G47-12) - GND (G47-14) | W - W-B | Lo-level CAN bus line | Engine switch on (IG) | Pulse generation
(see waveform 4) |
| SG-2 (G47-13) - Body ground | G - Body ground | Ground for pressure sensor | Always | Below 1 V |
| GND (G47-14) - Body ground | W-B - Body ground | Ground for main power supply | Always | Below 1 V |
| NAIN (G47-15) - GND (G47-14) (*3) | GR - W-B | No. 2 ion generator sub-assembly operation condition signal | Engine switch on (IG) | Below 1 V |
| Blower switch LO | ||||
| Ion generator switch (air purifier switch assembly) on | ||||
| NAIN (G47-15) - GND (G47-14) (*3) | GR - W-B | No. 2 ion generator sub-assembly operation condition signal | Engine switch on (IG) | 10 to 14 V |
| Blower switch LO | ||||
| Ion generator switch (air purifier switch assembly) off | ||||
| RCRL (G47-18) - Body ground (*2) | R - Body ground | Rear cooler control relay operation signal | Engine switch on (IG) | Below 1 V → 10 to 14 V |
| Rear blower switch OFF → ON | ||||
| MGC (G47-20) - GND (G47-14) (*4) | P - W-B | A/C compressor magnetic clutch operation signal | Engine idling | Below 1 V |
| Blower switch LO | ||||
| A/C switch ON | ||||
| B (G47-21) - GND (G47-14) | W - W-B | Power source (Back-up) | Always | 10 to 14 V |
| PTC2 (G47-22) - Body ground (*1) | L - Body ground | PTC No. 2 heater relay operation signal | Engine idling | Below 1 V → 10 to 14 V |
| Set temperature: MAX HOT | ||||
| Engine coolant temperature: Below 65°C (149°F) | ||||
| Ambient temperature: Below 10°C (50°F) | ||||
| Blower switch OFF → LO | ||||
| BLW (G47-23) - GND (G47-14) | P - W-B | Blower motor control signal | Engine switch on (IG) | Pulse generation
(see waveform 2) |
| Blower switch LO | ||||
| ALT (G47-25) - Body ground (*1) | Y - Body ground | Generator signal | Engine idling | Pulse generation |
| HLS (G47-27) - Body ground (*1) | V - Body ground | Headlight signal | Engine idling | Below 1 V |
| Headlight switch ON | ||||
| HLS (G47-27) - Body ground (*1) | V - Body ground | Headlight signal | Engine idling | 10 to 14 V |
| Headlight switch OFF | ||||
| TR (G47-29) - SG-4 (G47-34) | GR- B | Room temperature sensor signal | Engine switch on (IG) | 1.8 to 2.2 V |
| Vehicle interior temperature: 25°C (77°F) | ||||
| TSP (G47-32) - GND (G47-14) | V - W-B | Passenger side solar sensor signal | Engine switch on (IG) | 0.8 to 4.3 V |
| Solar sensor subject to electric light | ||||
| TSD (G47-33) - GND (G47-14) | R - W-B | Driver side solar sensor signal | Engine switch on (IG) | 0.8 to 4.3 V |
| Solar sensor subject to electric light | ||||
| SG-4 (G47-34) - Body ground | B - Body ground | Ground for room temperature sensor | Always | Below 1 V |
| LIN1 (G47-37) - GND (G47-14) | Y - W-B | LIN communication signal | Engine switch on (IG) | Pulse generation |
| RDEF (G47-38) - GND (G47-14) | W - W-B | Rear defogger switch signal | Engine switch on (IG)
Rear defogger switch OFF |
10 to 14 V |
| RDEF (G47-38) - GND (G47-14) | W - W-B | Rear defogger switch signal | Engine switch on (IG)
Rear defogger switch ON |
Below 1 V |
| RBUS (G48-1) - RBUG (G48-21) (*1) | SB - BE | BUS IC control signal (for Rear) | Engine switch on (IG) | Pulse generation |
| TEC (G48-4) - SGND (G48-19) (*1) | R - BR | Rear evaporator temperature sensor signal | Engine switch on (IG) | 1.4 to 1.8 V |
| Rear evaporator temperature: 15°C (59°F) | ||||
| SG-6 (G48-7) - Body ground | G - Body ground | Ground for rear room temperature sensor signal | Always | Below 1 V |
| NAI (G48-9) - GND2 (G48-20) (*3) | LG - W-B | Ion generator switch (air purifier switch assembly) indicator signal | Engine switch on (IG) | Below 1.5 V |
| Blower switch LO | ||||
| Ion generator switch (air purifier switch assembly) on | ||||
| NAI (G48-9) - GND2 (G48-20) (*3) | LG - W-B | Ion generator switch (air purifier switch assembly) indicator signal | Engine switch on (IG) | 10 to 14 V |
| Blower switch LO | ||||
| Ion generator switch (air purifier switch assembly) off | ||||
| NANO (G48-11) - GND2 (G48-20) (*3) | LG - W-B | No. 2 ion generator sub-assembly operation signal | Engine switch on (IG) | Below 1 V |
| Blower switch LO | ||||
| Ion generator switch (air purifier switch assembly) on | ||||
| NANO (G48-11) - GND2 (G48-20) (*3) | LG - W-B | No. 2 ion generator sub-assembly operation signal | Engine switch on (IG) | 4.75 to 5.25 V |
| Blower switch LO | ||||
| Ion generator switch (air purifier switch assembly) off | ||||
| BLIN (G48-13) - GND2 (G48-20) (*1) | Y - W-B | MPX communication signal (for Rear) | Engine switch on (IG) | Pulse generation |
| TR (G48-17) - SG-6 (G48-7) | B - G | Rear room temperature sensor signal | Engine switch on (IG) | 1.8 to 2.2 V |
| Vehicle interior temperature: 25°C (77°F) | ||||
| SGND (G48-19) - Body ground (*1) | BR - Body ground | Ground for rear evaporator temperature sensor signal | Always | Below 1 V |
| GND2 (G48-20) - Body ground (*1) | W-B - Body ground | Ground for power supply | Always | Below 1 V |
| RBUG (G48-21) - Body ground (*1) | BE - Body ground | Ground for BUS IC (for Rear) | Always | Below 1 V |
| BLWH (G48-22) - GND2 (G48-20) (*1) | Y - W-B | Blower motor control signal (for Rear) | Engine switch on (IG) | Pulse generation |
| Blower switch LO | ||||
| RBBU (G48-23) - RBUG (G48-21) (*1) | L - BE | Power supply for BUS IC (for Rear) | Engine switch on (IG) | 10 to 14 V |
| +B2 (G48-24) - GND2 (G48-20) (*1) | W - W-B | Power source (Back-up) (Rear) | Always | 10 to 14 V |
| BUS G (a1-2) - Body ground | - | Ground for BUS IC | Always | Below 1 V |
| BUS (a1-3) - BUS G (a1-2) | - | BUS IC control signal | Engine switch on (IG) | Pulse generation |
| B BUS (a1-4) - BUS G (a1-2) | - | Power supply for BUS IC | Engine switch on (IG) | 11 to 13 V |
| SG (a1-5) - Body ground | - | Ground for evaporator temperature sensor | Always | Below 1 V |
| TE (a1-6) - SG (a1-5) | - | Evaporator temperature sensor signal | Engine switch on (IG) | 1.4 to 1.8 V |
| Evaporator temperature: 15°C (59°F) |
Using an oscilloscope, check waveform 1.
| Item | Content |
|---|---|
| Symbol (Terminal No.) | SOL+ (G47-2) - GND (G47-14) |
| Tool Setting | 5 V/DIV., 500 μsec./DIV. |
| Condition | Engine idling, Blower switch LO, A/C switch ON |
Using an oscilloscope, check waveform 2.
| Item | Content |
|---|---|
| Symbol (Terminal No.) | BLW (G47-23) - GND (G47-14) |
| Tool Setting | 1 V/DIV., 500 μsec./DIV. |
| Condition | Engine switch on (IG), Blower switch LO |
When the blower level is increased, the duty ratio changes accordingly.
Using an oscilloscope, check waveform 3.
| Item | Content |
|---|---|
| Symbol (Terminal No.) | CANH (G47-11) - GND (G47-14) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine switch on (IG) |
The waveform varies depending on the CAN communication signal.
Using an oscilloscope, check waveform 4.
| Item | Content |
|---|---|
| Symbol (Terminal No.) | CANL (G47-12) - GND (G47-14) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine switch on (IG) |
The waveform varies depending on the CAN communication signal.
Using an oscilloscope, check waveform 5.
| Item | Content |
|---|---|
| Symbol (Terminal No.) | LOCK (G47-8) - GND (G47-14) |
| Tool Setting | 200 mV/DIV., 10 ms./DIV. |
| Condition | Engine idling, Blower switch LO, A/C switch ON |
The waveform varies depending on the CAN communication signal.
*1: for Rear Automatic A/C
*2: for Rear Manual A/C
*3: with Ion Generator Assembly
*4: for 2GR-FE
CHECK FRONT AIR CONDITIONING CONTROL ASSEMBLY
Measure the voltage of the connectors.
Check from the rear of the connector while it is connected to the air conditioning control assembly.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| IG+ (G37-1) - GND (G37-6) | B - W-B | Power source (IG) | Engine switch on (IG) | 10 to 14 V |
| LIN1 (G37-3) - GND (G37-6) | Y - W-B | LIN communication signal | Engine switch on (IG) | Pulse generation |
| GND (G37-6) - Body ground | W-B - Body ground | Ground for front air conditioning control assembly | Always | Below 1 V |
CHECK REAR AIR CONDITIONING CONTROL PANEL (for Rear Automatic A/C)
Measure the voltage of the connectors.
Check from the rear of the connector while it is connected to the rear air conditioning control panel.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| IG+ (Q11-7) - E (Q11-12) | B - W-B | Power source (IG) | Engine switch on (IG) | 10 to 14 V |
| MPX- (Q11-5) - E (Q11-12) | Y - W-B | MPX communication signal | Engine switch on (IG) | Pulse generation |
| E (Q11-12) - Body ground | W-B - Body ground | Ground for rear air conditioning control panel | Always | Below 1 V |