Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM U

AIR CONDITIONING  AIR CONDITIONING SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER


U186376E02
3.865,0.354 4.167,0.531 0.302,0.177 10 false G47 1.688,0.354 1.99,0.531 0.302,0.177 10 false G48 5.573,0.344 5.833,0.521 0.26,0.177 10 false a1

a.

Measure the voltage of the connectors.

HINT:

Check from the rear of the connector while it is connected to the air conditioning amplifier.


Symbol (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
IG+ (G47-1) - GND (G47-14) B - W-B Power source (IG) Engine switch on (IG) 10 to 14 V
SOL+ (G47-2) - GND (G47-14) W - W-B A/C compressor operation signal Engine idling Pulse generation
(see waveform 1)
Blower switch LO
A/C switch ON
PTC1 (G47-3) - Body ground (*1) R - Body ground PTC No. 1 heater relay operation signal Engine idling Below 1 V → 10 to 14 V
Set temperature: MAX HOT
Engine coolant temperature: Below 65°C (149°F)
Ambient temperature: Below 10°C (50°F)
Blower switch OFF → LO
PTC3 (G47-4) - Body ground (*1) V - Body ground PTC No. 3 heater relay operation signal Engine idling Below 1 V → 10 to 14 V
Set temperature: MAX HOT
Engine coolant temperature: Below 65°C (149°F)
Ambient temperature: Below 10°C (50°F)
Blower switch OFF → LO
TAM (G47-5) - GND (G47-14) L - W-B Ambient temperature sensor signal Engine switch on (IG) 1.8 to 2.2 V
Ambient temperature: 25°C (77°F)
LOCK (G47-8) - GND (G47-14) (*4) V - W-B A/C lock sensor signal Engine idling Pulse generation
(see waveform 5)
A/C switch ON
Blower switch LO
PRE (G47-9) - SG-2 (G47-13) GR - G Air conditioning pressure sensor signal Refrigerant pressure: Normal 0.76 to 4.74 V
PRE (G47-9) - SG-2 (G47-13) GR - G Air conditioning pressure sensor signal Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi]) Below 0.76 V
PRE (G47-9) - SG-2 (G47-13) GR - G Air conditioning pressure sensor signal Refrigerant pressure: Abnormal (more than 3.14 MPa [32 kgf/cm2, 455 psi]) 4.74 V or higher
S5-3 (G47-10) - GND (G47-14) B - W-B Power supply for pressure sensor Engine switch on (IG) 4.5 to 5.5 V
CANH (G47-11) - GND (G47-14) V - W-B Hi-level CAN bus line Engine switch on (IG) Pulse generation
(see waveform 3)
CANL (G47-12) - GND (G47-14) W - W-B Lo-level CAN bus line Engine switch on (IG) Pulse generation
(see waveform 4)
SG-2 (G47-13) - Body ground G - Body ground Ground for pressure sensor Always Below 1 V
GND (G47-14) - Body ground W-B - Body ground Ground for main power supply Always Below 1 V
NAIN (G47-15) - GND (G47-14) (*3) GR - W-B No. 2 ion generator sub-assembly operation condition signal Engine switch on (IG) Below 1 V
Blower switch LO
NAIN (G47-15) - GND (G47-14) (*3) GR - W-B No. 2 ion generator sub-assembly operation condition signal Engine switch on (IG) 10 to 14 V
Blower switch OFF
RCRL (G47-18) - Body ground (*2) R - Body ground Rear cooler control relay operation signal Engine switch on (IG) Below 1 V → 10 to 14 V
Rear blower switch OFF → ON
MGC (G47-20) - GND (G47-14) (*4) P - W-B A/C compressor magnetic clutch operation signal Engine idling Below 1 V
Blower switch LO
A/C switch ON
B (G47-21) - GND (G47-14) W - W-B Power source (Back-up) Always 10 to 14 V
PTC2 (G47-22) - Body ground (*1) L - Body ground PTC No. 2 heater relay operation signal Engine idling Below 1 V → 10 to 14 V
Set temperature: MAX HOT
Engine coolant temperature: Below 65°C (149°F)
Ambient temperature: Below 10°C (50°F)
Blower switch OFF → LO
BLW (G47-23) - GND (G47-14) P - W-B Blower motor control signal Engine switch on (IG) Pulse generation
(see waveform 2)
Blower switch LO
ALT (G47-25) - Body ground (*1) Y - Body ground Generator signal Engine idling Pulse generation
HLS (G47-27) - Body ground (*1) V - Body ground Headlight signal Engine idling Below 1 V
Headlight switch ON
HLS (G47-27) - Body ground (*1) V - Body ground Headlight signal Engine idling 10 to 14 V
Headlight switch OFF
TR (G47-29) - SG-4 (G47-34) GR- B Room temperature sensor signal Engine switch on (IG) 1.8 to 2.2 V
Vehicle interior temperature: 25°C (77°F)
TSP (G47-32) - GND (G47-14) V - W-B Passenger side solar sensor signal Engine switch on (IG) 0.8 to 4.3 V
Solar sensor subject to electric light
TSD (G47-33) - GND (G47-14) R - W-B Driver side solar sensor signal Engine switch on (IG) 0.8 to 4.3 V
Solar sensor subject to electric light
SG-4 (G47-34) - Body ground B - Body ground Ground for room temperature sensor Always Below 1 V
LIN1 (G47-37) - GND (G47-14) Y - W-B LIN communication signal Engine switch on (IG) Pulse generation
RDEF (G47-38) - GND (G47-14) W - W-B Rear defogger switch signal Engine switch on (IG)
Rear defogger switch OFF
10 to 14 V
RDEF (G47-38) - GND (G47-14) W - W-B Rear defogger switch signal Engine switch on (IG)
Rear defogger switch ON
Below 1 V
RBUS (G48-1) - RBUG (G48-21) (*1) SB - BE BUS IC control signal (for Rear) Engine switch on (IG) Pulse generation
TEC (G48-4) - SGND (G48-19) (*1) R - BR Rear evaporator temperature sensor signal Engine switch on (IG) 1.4 to 1.8 V
Rear evaporator temperature: 15°C (59°F)
SG-6 (G48-7) - Body ground G - Body ground Ground for rear room temperature sensor signal Always Below 1 V
NANO (G48-11) - GND2 (G48-20) (*3) LG - W-B No. 2 ion generator sub-assembly operation signal Engine switch on (IG) Below 1 V
Blower switch LO
NANO (G48-11) - GND2 (G48-20) (*3) LG - W-B No. 2 ion generator sub-assembly operation signal Engine switch on (IG) 4.75 to 5.25 V
Blower switch OFF
BLIN (G48-13) - GND2 (G48-20) (*1) Y - W-B MPX communication signal (for Rear) Engine switch on (IG) Pulse generation
TR (G48-17) - SG-6 (G48-7) B - G Rear room temperature sensor signal Engine switch on (IG) 1.8 to 2.2 V
Vehicle interior temperature: 25°C (77°F)
SGND (G48-19) - Body ground (*1) BR - Body ground Ground for rear evaporator temperature sensor signal Always Below 1 V
GND2 (G48-20) - Body ground (*1) W-B - Body ground Ground for power supply Always Below 1 V
RBUG (G48-21) - Body ground (*1) BE - Body ground Ground for BUS IC (for Rear) Always Below 1 V
BLWH (G48-22) - GND2 (G48-20) (*1) Y - W-B Blower motor control signal (for Rear) Engine switch on (IG) Pulse generation
Blower switch LO
RBBU (G48-23) - RBUG (G48-21) (*1) L - BE Power supply for BUS IC (for Rear) Engine switch on (IG) 10 to 14 V
+B2 (G48-24) - GND2 (G48-20) (*1) W - W-B Power source (Back-up) (Rear) Always 10 to 14 V
BUS G (a1-2) - Body ground - Ground for BUS IC Always Below 1 V
BUS (a1-3) - BUS G (a1-2) - BUS IC control signal Engine switch on (IG) Pulse generation
B BUS (a1-4) - BUS G (a1-2) - Power supply for BUS IC Engine switch on (IG) 11 to 13 V
SG (a1-5) - Body ground - Ground for evaporator temperature sensor Always Below 1 V
TE (a1-6) - SG (a1-5) - Evaporator temperature sensor signal Engine switch on (IG) 1.4 to 1.8 V
Evaporator temperature: 15°C (59°F)


b.
E359919E01
2.844,0.135 3.396,0.333 0.552,0.198 10 false 5 V/DIV. 3.031,1.177 3.365,1.375 0.333,0.198 10 false GND 1.667,1.938 2.74,2.167 1.073,0.229 10 false 500 μsec./DIV.

Using an oscilloscope, check waveform 1.

Compressor and pulley operation signal
Item Content
Symbol (Terminal No.) SOL+ (G47-2) - GND (G47-14)
Tool Setting 5 V/DIV., 500 μsec./DIV.
Condition Engine idling, Blower switch LO, A/C switch ON


c.
E103396E66
2.927,1.656 3.302,1.833 0.375,0.177 10 false GND 2.74,0.26 3.271,0.458 0.531,0.198 10 false 1 V/DIV. 1.063,1.958 2.125,2.135 1.063,0.177 10 false 500 μsec./DIV.

Using an oscilloscope, check waveform 2.

Blower motor control signal
Item Content
Symbol (Terminal No.) BLW (G47-23) - GND (G47-14)
Tool Setting 1 V/DIV., 500 μsec./DIV.
Condition Engine switch on (IG), Blower switch LO

HINT:

When the blower level is increased, the duty ratio changes accordingly.



d.
A393965E01
3,1.385 3.417,1.594 0.417,0.208 10 false GND 2.76,0.302 3.313,0.531 0.552,0.229 10 false 1 V/DIV. 1.583,1.885 2.51,2.104 0.927,0.219 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 3.

CAN communication signal
Item Content
Symbol (Terminal No.) CANH (G47-11) - GND (G47-14)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



e.
A086155E95
3.01,1.385 3.365,1.583 0.354,0.198 10 true GND 2.76,0.229 3.292,0.406 0.531,0.177 10 false 1 V/DIV. 1.573,1.896 2.49,2.073 0.917,0.177 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 4.

CAN communication signal
Item Content
Symbol (Terminal No.) CANL (G47-12) - GND (G47-14)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



f.
E147961E01
0.037,0.959 0.396,1.115 0.360,0.156 10 GND 1.349,1.728 2.092,1.893 0.744,0.165 10 10 ms./DIV. 2.448,0.204 3.261,0.351 0.813,0.147 10 200 mV/DIV.

Using an oscilloscope, check waveform 5.

A/C compressor lock sensor signal
Item Content
Symbol (Terminal No.) LOCK (G47-8) - GND (G47-14)
Tool Setting 200 mV/DIV., 10 ms./DIV.
Condition Engine idling, Blower switch LO, A/C switch ON

HINT:

The waveform varies depending on the CAN communication signal.


*1: for Rear Automatic A/C

*2: for Rear Manual A/C

*3: w/ Ion Generator Assembly

*4: for 2GR-FE



CHECK FRONT AIR CONDITIONING CONTROL (for LHD)


U186379E02
3.458,0.229 3.771,0.406 0.313,0.177 10 false G37

a.

Measure the voltage of the connectors.

HINT:

Check from the rear of the connector while it is connected to the air conditioning control.


Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
IG+ (G37-1) - GND (G37-6) B - W-B Power source (IG) Engine switch on (IG) 10 to 14 V
LIN1 (G37-3) - GND (G37-6) Y - W-B LIN communication signal Engine switch on (IG) Pulse generation
GND (G37-6) - Body ground W-B - Body ground Ground for front air conditioning control assembly Always Below 1 V



CHECK FRONT AIR CONDITIONER PANEL SUB-ASSEMBLY (for RHD)


U189988E02
3.417,0.156 3.875,0.344 0.458,0.188 10 false G120

a.

Measure the voltage of the connectors.

HINT:

Check from the rear of the connector while it is connected to the air conditioner panel sub-assembly.


Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
+B (G120-1) - GND (G120-4) L - W-B Power source (Back-up) Engine switch off 10 to 14 V
IG+ (G120-2) - GND (G120-4) B - W-B Power source (IG) Engine switch on (IG) 10 to 14 V
GND (G120-4) - Body ground W-B - Body ground Ground for front air conditioning control assembly Always Below 1 V
ACC (G120-5) - GND (G120-4) R - W-B Power source (ACC) Engine switch on (ACC) 10 to 14 V
LIN1 (G120-8) - GND (G120-4) Y - W-B LIN communication signal Engine switch on (IG) Pulse generation



CHECK REAR AIR CONDITIONING CONTROL PANEL (for Rear Automatic A/C)


U189888E02
3.427,0.302 3.75,0.521 0.323,0.219 10 false Q23

a.

Measure the voltage of the connectors.

HINT:

Check from the rear of the connector while it is connected to the rear air conditioning control panel.


Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
IG+ (Q23-7) - E (Q23-12) B - W-B Power source (IG) Engine switch on (IG) 10 to 14 V
MPX- (Q23-5) - E (Q23-12) Y - W-B MPX communication signal Engine switch on (IG) Pulse generation
E (Q23-12) - Body ground W-B - Body ground Ground for rear air conditioning control panel Always Below 1 V