Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM C

AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1412/12  Ambient Temperature Sensor Circuit  


DESCRIPTION

The ambient temperature sensor is installed in the front part of the condenser to detect the ambient temperature and control the air conditioner. The sensor is connected to the air conditioning amplifier and detects fluctuations in the ambient temperature. This data is used for controlling the room temperature. The sensor sends a signal to the air conditioning amplifier. The resistance of the ambient temperature sensor changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier applies a voltage (5 V) to the ambient temperature sensor and reads voltage changes as changes in the resistance of the ambient temperature sensor.

DTC No. DTC Detection Condition Trouble Area
B1412/12 Open or short in ambient temperature sensor circuit
·

Ambient temperature sensor

·

Wire harness between ambient temperature sensor and combination meter

·

Combination meter

·

Air conditioning amplifier

·

CAN communication line



WIRING DIAGRAM

E127563E16
4.167,2.354 5.74,2.531 1.573,0.177 10 false Air Conditioning Amplifier 4.406,0.885 4.719,1.063 0.313,0.177 10 false TAM 4.385,1.781 4.729,1.958 0.344,0.177 10 false SG-2 0.333,1.302 1.656,1.698 1.323,0.396 10 false Ambient Temperature Sensor 0.333,1.146 0.646,1.313 0.313,0.167 10 false B15 1.979,1.083 2.146,1.365 0.167,0.281 10 false 1 2,1.604 2.25,1.813 0.25,0.208 10 false 2 4.156,0.74 4.323,0.927 0.167,0.188 10 false 5 4.094,1.656 4.354,1.865 0.26,0.208 10 false 13 4.156,2.198 4.438,2.427 0.281,0.229 10 false G47

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (AMBI TEMP SENS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the intelligent tester main switch ON.


c.

Select the item below in the Data List, and read the value displayed on the intelligent tester.

Air conditioning amplifier:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Ambi Temp Sens Ambient temperature sensor /
Min.: -30.8°C (-23.44°F)
Max.: 50.8°C (123.44°F)
Actual ambient temperature is displayed Open circuit: -53°C (-63.4°F)
Short circuit: 120°C (248°F)


OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
NG A
OK (Checking from PROBLEM SYMPTOMS TABLE) B
OK (Checking from DTC) C



A

2.INSPECT AMBIENT TEMPERATURE SENSOR

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER

2.INSPECT AMBIENT TEMPERATURE SENSOR
E358377E01
2.917,1.448 2.583,0.719 false 1.75,0.604 2.74,0.885 0.99,0.281 10 false Sensor Area 4.167,0.042 5.49,0.292 1.323,0.25 10 false Resistance (kΩ) 4.083,0.25 4.396,0.448 0.313,0.198 10 false 4.0 4.083,0.458 4.396,0.656 0.313,0.198 10 false 3.5 4.073,0.677 4.385,0.875 0.313,0.198 10 false 3.0 4.344,2.135 4.656,2.333 0.313,0.198 10 false 10 4.083,0.906 4.396,1.104 0.313,0.198 10 false 2.5 4.083,1.135 4.396,1.333 0.313,0.198 10 false 2.0 4.083,1.365 4.396,1.563 0.313,0.198 10 false 1.5 4.083,1.583 4.396,1.781 0.313,0.198 10 false 1.0 4.083,1.823 4.396,2.021 0.313,0.198 10 false 0.5 4.083,2.021 4.396,2.219 0.313,0.198 10 false 0.0 4.323,2.281 4.635,2.479 0.313,0.198 10 false (50) 4.729,2.135 5.042,2.333 0.313,0.198 10 false 20 4.698,2.281 5.01,2.479 0.313,0.198 10 false (68) 5.188,2.135 5.5,2.333 0.313,0.198 10 false 30 5.156,2.281 5.469,2.479 0.313,0.198 10 false (86) 5.667,2.135 5.979,2.333 0.313,0.198 10 false 40 5.604,2.281 5.979,2.5 0.375,0.219 10 false (104) 6.115,2.135 6.427,2.333 0.313,0.198 10 false 50 6.063,2.281 6.427,2.51 0.365,0.229 10 false (122) 6.531,2.135 6.844,2.333 0.313,0.198 10 false 60 6.479,2.281 6.844,2.531 0.365,0.25 10 false (140) 3.021,2.365 4.469,2.698 1.448,0.333 10 false Temperature °C (°F)

a.

Remove the ambient temperature sensor.


b.

Measure the resistance of the sensor.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 10°C (50°F) 3.00 to 3.73 kΩ
1 - 2 15°C (50°F) 2.45 to 2.88 kΩ
1 - 2 20°C (68°F) 1.95 to 2.30 kΩ
1 - 2 25°C (77°F) 1.60 to 1.80 kΩ
1 - 2 30°C (86°F) 1.28 to 1.47 kΩ
1 - 2 35°C (95°F) 1.00 to 1.22 kΩ
1 - 2 40°C (104°F) 0.80 to 1.00 kΩ
1 - 2 45°C (113°F) 0.65 to 0.85 kΩ
1 - 2 50°C (122°F) 0.50 to 0.70 kΩ
1 - 2 55°C (131°F) 0.44 to 0.60 kΩ
1 - 2 60°C (140°F) 0.36 to 0.50 kΩ


NOTICE:
·

Touching the sensor even slightly may change the resistance value. Be sure to hold the connector of the sensor.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).




OK

3.CHECK WIRE HARNESS (AMBIENT TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)

NG

REPLACE AMBIENT TEMPERATURE SENSOR

3.CHECK WIRE HARNESS (AMBIENT TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)
E358383E01
0.594,1.281 1.01,1.531 0.417,0.25 1.625,2.531 2.042,2.781 0.417,0.25 1.375,4.229 1.74,3.854 true 2.708,4.219 2.458,3.854 true 0.146,0.104 1.5,0.438 1.354,0.333 10 false Wire Harness Side: 0.917,0.635 2.865,0.875 1.948,0.24 10 false Ambient Temperature Sensor 0.688,1.323 1.208,1.573 0.521,0.25 10 false B15 1.031,2.146 2.948,2.51 1.917,0.365 10 false Air Conditioning Amplifier 1.688,2.573 2.208,2.823 0.521,0.25 10 false G47 1.125,4.24 1.646,4.49 0.521,0.25 10 false SG-2 2.615,4.25 3.135,4.5 0.521,0.25 10 false TAM

a.

Disconnect the B15 sensor connector.


b.

Disconnect the G47 amplifier connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
B15-1 - G47-5 (TAM) Below 1 Ω
B15-2 - G47-13 (SG-2) Below 1 Ω
G47-5 (TAM) - Body ground 10 kΩ or higher
G47-13 (SG-2) - Body ground 10 kΩ or higher




OK

REPLACE AIR CONDITIONING AMPLIFIER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR