Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM C

AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1413/13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor (evaporator temperature sensor) is installed on the evaporator in the air conditioning unit to detect the temperature of the cooled air that has passed through the evaporator and to control the air conditioner. It sends signals to the air conditioning amplifier. The signals change in accordance with the resistance of the No. 1 cooler thermistor (evaporator temperature sensor). As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases. The air conditioning amplifier applies a voltage (5 V) to the No. 1 cooler thermistor (evaporator temperature sensor) and reads voltage changes as changes in the resistance of the No. 1 cooler thermistor (evaporator temperature sensor). This sensor is used for frost prevention.

DTC No. DTC Detection Condition Trouble Area
B1413/13 Open or short in evaporator temperature sensor circuit
·

No. 1 cooler thermistor (evaporator temperature sensor)

·

Wire harness between No. 1 cooler thermistor (evaporator temperature sensor) and air conditioning amplifier

·

Air conditioning amplifier



WIRING DIAGRAM

E133418E10
5.135,0.781 5.427,0.958 0.292,0.177 10 false TE 5.146,1.385 5.458,1.563 0.313,0.177 10 false SG 4.896,2 6.469,2.302 1.573,0.302 10 false a1 3.167,2.031 4.719,2.208 1.552,0.177 10 false Air Conditioning Harness 0.729,2.01 2.833,2.354 2.104,0.344 10 false No. 1 Cooler Thermistor (Evaporator Temperature Sensor) 4.906,0.635 5.104,0.781 0.198,0.146 10 false 6 4.917,1.281 5.115,1.427 0.198,0.146 10 false 5 4.885,2.177 6.458,2.479 1.573,0.302 10 false Air Conditioning Amplifier

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (EVAP FIN TEMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the intelligent tester main switch ON.


c.

Select the item below in the Data List, and read the value displayed on the intelligent tester.

Air conditioning amplifier:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Evap Fin Temp Evaporator temperature sensor / Min.: -29.7°C (-21.46°F)
Max.: 59.6°C (139.28°F)
Actual evaporator temperature is displayed Open circuit: -29.7°C (-21.46°F)
Short circuit: 59.6°C (139.28°F)


OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
NG A
OK (Checking from PROBLEM SYMPTOMS TABLE) B
OK (Checking from DTC) C



A

2.INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER

2.INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)
E356088E02
0.719,2.99 0.927,2.604 false 1.781,0.396 1.313,0.208 false 0.875,1.781 1.052,1.448 false 0.604,0.115 1.396,0.375 0.792,0.26 10 false Evaporator 0.969,2.479 1.854,2.719 0.885,0.24 10 false Sensor Area 3.688,0.531 5.01,0.792 1.323,0.26 10 false Resistance (kΩ) 4.885,3.188 6.323,3.49 1.438,0.302 10 false Temperature °C (°F) 3.927,0.865 4.24,1.063 0.313,0.198 10 false 10.0 4,1.042 4.24,1.24 0.24,0.198 10 false 9.0 4.156,2.75 4.469,2.948 0.313,0.198 10 false -10 4.792,2.75 5.104,2.948 0.313,0.198 10 false 0 5.333,2.75 5.646,2.948 0.313,0.198 10 false 10 5.917,2.75 6.229,2.948 0.313,0.198 10 false 20 6.49,2.75 6.802,2.948 0.313,0.198 10 false 30 4.167,2.917 4.479,3.115 0.313,0.198 10 false (14) 4,1.219 4.24,1.417 0.24,0.198 10 false 8.0 4,1.406 4.24,1.604 0.24,0.198 10 false 7.0 4,1.563 4.24,1.76 0.24,0.198 10 false 6.0 4,1.74 4.24,1.938 0.24,0.198 10 false 5.0 4,1.917 4.24,2.115 0.24,0.198 10 false 4.0 4,2.094 4.24,2.292 0.24,0.198 10 false 3.0 4,2.271 4.24,2.469 0.24,0.198 10 false 2.0 4,2.438 4.24,2.635 0.24,0.198 10 false 1.0 4,2.583 4.24,2.781 0.24,0.198 10 false 0.0 4.708,2.917 5.021,3.115 0.313,0.198 10 false (32) 5.302,2.917 5.615,3.115 0.313,0.198 10 false (50) 5.865,2.917 6.177,3.115 0.313,0.198 10 false (68) 6.448,2.917 6.76,3.115 0.313,0.198 10 false (86) 0.198,1.823 1.823,2.104 1.625,0.281 10 false No. 1 Cooler Thermistor 0.792,3.427 2.417,3.708 1.625,0.281 10 false No. 1 Cooler Thermistor

a.

Remove the No. 1 cooler thermistor.


b.

Measure the resistance of the thermistor.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 -10°C (14°F) 7.30 to 9.10 kΩ
1 - 2 -5°C (23°F) 5.65 to 6.95 kΩ
1 - 2 0°C (32°F) 4.40 to 5.35 kΩ
1 - 2 5°C (41°F) 3.40 to 4.15 kΩ
1 - 2 10°C (50°F) 2.70 to 3.25 kΩ
1 - 2 15°C (59°F) 2.14 to 2.58 kΩ
1 - 2 20°C (68°F) 1.71 to 2.05 kΩ
1 - 2 25°C (77°F) 1.38 to 1.64 kΩ
1 - 2 30°C (86°F) 1.11 to 1.32 kΩ



NOTICE:
·

Touching the thermistor even slightly may change the resistance value. Be sure to hold the connector of the thermistor.

·

When measuring, the thermistor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).



OK

REPLACE AIR CONDITIONING HARNESS

NG

REPLACE NO. 1 COOLER THERMISTOR