Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM J

AIR CONDITIONING  AIR CONDITIONING SYSTEM  IG Power Source Circuit  


DESCRIPTION

This is the main power source supplied to the air conditioning amplifier when the ignition switch is on (IG). This power source is used for operating components, such as the air conditioning amplifier and servo motors.

WIRING DIAGRAM

E259478E02
5.375,1.156 5.656,1.333 0.281,0.177 10 false G47 5.375,3.76 5.656,3.938 0.281,0.177 10 false G47 5.365,4.229 5.646,4.406 0.281,0.177 10 false G48 0.802,3.583 1.406,3.875 0.604,0.292 10 false FL MAIN 0.938,4.26 1.427,4.552 0.49,0.292 10 false Battery 3.49,1.896 4.083,2.083 0.594,0.188 10 false RH-IG 1 4.469,2.865 5.521,3.052 1.052,0.188 10 false Main Body ECU 1.917,4.563 2.865,4.875 0.948,0.313 10 false G31 5.406,4.948 7.094,5.302 1.688,0.354 10 false Air Conditioning Amplifier 4.469,1.302 5.271,1.479 0.802,0.177 10 false RH ECU-IG 0.833,1.969 1.156,2.26 0.323,0.292 10 false ALT 0.99,1.323 1.885,1.573 0.896,0.25 10 false RH-MAIN-JB 2.625,3.917 2.917,4.083 0.292,0.167 10 false SS1 3.813,3.813 4.302,3.979 0.49,0.167 10 false SSW1 3.823,3.198 4.313,3.365 0.49,0.167 10 false AM2 3.823,2.729 4.313,2.896 0.49,0.167 10 false AM1 3.813,2.281 4.302,2.448 0.49,0.167 10 false IGID 3.813,4.167 4.302,4.333 0.49,0.167 10 false SSW2 2.625,4.292 2.927,4.458 0.302,0.167 10 false SS2 1.833,4.292 2.177,4.458 0.344,0.167 10 false GND 1.844,2.885 2.615,3.156 0.771,0.271 10 false AM2 NO. 2 1.021,2.896 1.698,3.167 0.677,0.271 10 false F/B BATT 5.75,1.156 6.104,1.354 0.354,0.198 10 false IG+ 5.74,4.219 6.292,4.438 0.552,0.219 10 false GND2* 5.75,3.75 6.188,3.969 0.438,0.219 10 false GND 5.458,0.948 5.615,1.125 0.156,0.177 10 false 1 3.448,2.292 3.729,2.469 0.281,0.177 10 false G57 3.542,2.104 3.698,2.281 0.156,0.177 10 false 3 3.448,2.729 3.729,2.906 0.281,0.177 10 false G57 3.531,2.542 3.688,2.719 0.156,0.177 10 false 6 3.448,3.198 3.729,3.375 0.281,0.177 10 false G58 3.531,3.01 3.688,3.188 0.156,0.177 10 false 1 3.448,3.813 3.729,3.99 0.281,0.177 10 false G57 3.5,3.625 3.667,3.802 0.167,0.177 10 false 17 3.448,4.177 3.729,4.354 0.281,0.177 10 false G57 3.5,4.01 3.667,4.188 0.167,0.177 10 false 16 2.969,3.719 3.125,3.896 0.156,0.177 10 false 7 1.635,4 1.792,4.177 0.156,0.177 10 false 5 2.969,4.083 3.125,4.26 0.156,0.177 10 false 2 5.417,3.563 5.583,3.74 0.167,0.177 10 false 14 5.417,4.042 5.583,4.219 0.167,0.177 10 false 20 2.479,5.219 4.073,5.458 1.594,0.24 10 false *: w/ Rear Automatic A/C 1.927,4.729 2.875,5.042 0.948,0.313 10 false Engine Switch

PROCEDURE

1.INSPECT FUSE (RH ECU-IG)
a.

Remove the RH ECU-IG fuse from the instrument panel junction block RH.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

2.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

REPLACE FUSE

2.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BATTERY)
U189847E02
2.615,2.156 2.885,2.875 false 0.083,0.073 1.365,0.26 1.281,0.188 10 false Wire Harness Side: 0.938,0.521 2.51,0.698 1.573,0.177 10 false Air Conditioning Amplifier 2.917,2.875 3.24,3.052 0.323,0.177 10 false IG+ 1.802,1.104 2.083,1.281 0.281,0.177 10 false G47

a.

Disconnect the G47 amplifier connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
G47-1 (IG+) - Body ground Engine switch on (IG) 10 to 14 V




OK

3.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BODY GROUND)
U189858E02
1.698,2.156 2.115,2.719 true 0.563,2.25 0.948,2.802 true 0.49,1.052 0.771,1.229 0.281,0.177 10 false G48 0.094,0.031 1.375,0.219 1.281,0.188 10 false Wire Harness Side: 0.135,3.146 1.833,3.385 1.698,0.24 10 false *: w/ Rear Automatic A/C 0.917,0.521 2.49,0.698 1.573,0.177 10 false Air Conditioning Amplifier 2.146,2.708 2.469,2.885 0.323,0.177 10 false GND 1.792,1.094 2.073,1.271 0.281,0.177 10 false G47 1.01,2.771 1.469,2.948 0.458,0.177 10 false GND2*

a.

Disconnect the G47 and G48 amplifier connectors.


b.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G47-14 (GND) - Body ground Below 1 Ω
G48-20 (GND2)* - Body ground Below 1 Ω


HINT:

*: w/ Rear automatic A/C




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR