Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM J

AIR CONDITIONING  AIR CONDITIONING SYSTEM  Blower Motor Circuit  


DESCRIPTION

The blower motor is operated by signals from the air conditioning amplifier. Blower motor speed signals are transmitted in accordance with changes in the duty ratio.

E359917E01
2.844,1.177 3.875,1.479 1.031,0.302 10 false Blower Motor 4.229,0.885 5,1.188 0.771,0.302 10 false BLW 4.552,1.521 5.427,1.813 0.875,0.292 10 false Duty Control 4.146,2.406 5.948,2.656 1.802,0.25 10 false Air Conditioning Amplifier

WIRING DIAGRAM

E123559E17
5.896,0.875 6.25,1.208 0.354,0.333 10 false BLW 0.927,2.708 1.281,3.042 0.354,0.333 10 false GND 1.073,0.875 1.281,1.156 0.208,0.281 10 false SI 5.417,3.135 7.021,3.51 1.604,0.375 10 false G47 0.313,3.24 1.25,3.563 0.938,0.323 10 false G42 1.031,2.104 1.24,2.438 0.208,0.333 10 false +B 5.875,2.76 6.24,3.104 0.365,0.344 10 false GND 3.25,1.927 3.938,2.229 0.688,0.302 10 false FL MAIN 4.365,2.573 5.052,2.875 0.688,0.302 10 false Battery 1.813,1.938 2.198,2.24 0.385,0.302 10 false HTR 2.604,1.927 2.99,2.229 0.385,0.302 10 false ALT 5.604,0.708 5.833,0.875 0.229,0.167 10 false 23 1.385,1.958 1.615,2.125 0.229,0.167 10 false 1 1.396,0.76 1.625,0.927 0.229,0.167 10 false 2 1.396,2.583 1.625,2.75 0.229,0.167 10 false 3 5.563,2.635 5.792,2.802 0.229,0.167 10 false 14 5.427,3.302 7.031,3.677 1.604,0.375 10 false Air Conditioning Amplifier 0.323,3.396 1.26,3.719 0.938,0.323 10 false Blower Motor

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (BLOWER MOTOR)
a.

Connect the GTS to the DLC3.


b.

Turn the Engine switch on (IG) and turn the GTS on.


c.

Perform the Active Test by following the prompts on the tester.

Air conditioning amplifier:
Item Test Details / Display Diagnostic Note
Blower Motor Blower motor /
Min.: 0, Max.: 31
-


Result
Result Proceed to
NG (blower motor does not operate) A
NG (blower motor operates but does not change speed) B
OK C



A

2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BODY GROUND)

C

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BODY GROUND)
a.

Disconnect the G42 motor connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
G42-3 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BATTERY)
a.

Disconnect the G42 motor connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
G42-1 (+B) - Body ground Engine switch on (IG) 10 to 14 V




OK

4.CHECK BLOWER W/ FAN MOTOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK BLOWER W/ FAN MOTOR SUB-ASSEMBLY
U189986E02
1.667,1.021 1.281,0.323 false 1.5,3.354 1.208,2.656 false 1.813,1.021 2.115,0.313 false 1.646,3.365 2.302,2.635 false 0.083,0.052 0.708,0.208 0.625,0.156 10 false for RHD: 1.031,0.083 1.542,0.271 0.51,0.188 10 false GND(-) 0.167,0.5 0.49,0.677 0.323,0.177 10 false G42 0.99,2.406 1.5,2.594 0.51,0.188 10 false GND(-) 2,0.094 2.51,0.281 0.51,0.188 10 false SI(+) 2.198,2.417 2.708,2.604 0.51,0.188 10 false SI(+) 0.083,2.375 0.708,2.531 0.625,0.156 10 false for LHD: 0.177,4 0.5,4.177 0.323,0.177 10 false G42

a.

Disconnect the G47 amplifier connector.


b.

Connect the G42 motor connector.


c.

Measure the voltage of the connector.

Standard voltage:
Tester Connection Condition Specified Condition
G42-2 (SI) - G42-3 (GND) Engine switch on (IG) 4.5 to 5.5 V




OK

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BODY GROUND)

NG

REPLACE BLOWER W/ FAN MOTOR SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BODY GROUND)
a.

Disconnect the G47 amplifier connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
G47-23 (BLW) - G47-14 (GND) Engine switch on (IG)
Blower switch OFF
4.5 to 5.5 V




OK

6.CHECK AIR CONDITIONING AMPLIFIER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK AIR CONDITIONING AMPLIFIER
E358388E01
2.167,0.281 2.583,0.531 0.417,0.25 1.302,1.594 1.719,0.99 true 2.74,1.677 2.458,1.073 true 0.531,0.104 2.469,0.344 1.938,0.24 10 false Air Conditioning Amplifier 2.229,0.323 2.667,0.552 0.438,0.229 10 false G47 1,1.594 1.438,1.823 0.438,0.229 10 false GND 2.708,1.729 3.146,1.958 0.438,0.229 10 false BLW 0.229,1.979 1.073,2.229 0.844,0.25 10 false Waveform: 0.604,2.323 2.552,2.646 1.948,0.323 10 false Blower Motor Control Signal 2.615,2.583 3.26,2.844 0.646,0.26 10 false 1 V/DIV. 2.833,4.031 3.271,4.26 0.438,0.229 10 false GND 1.104,4.344 2.417,4.615 1.313,0.271 10 false 500 μsec./DIV.

a.

Remove the air conditioning amplifier with its connectors still connected.


b.

Check the waveform of the amplifier connector.

OK:

Waveform is as shown in the illustration.


HINT:

The waveform varies with the blower level.


Item Content
Tester Connection BLW (G47-23) - GND (G47-14)
Tool Setting 1 V/DIV., 500 μsec./DIV.
Condition Engine switch on (IG)
Blower switch LO



OK

REPLACE BLOWER W/ FAN MOTOR SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER