Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM J

AIR CONDITIONING  AIR CONDITIONING SYSTEM  PTC Heater Circuit  


DESCRIPTION

PTC heater relays are closed in accordance with signals from the air conditioning amplifier and power is supplied to the PTC heater installed on the radiator heater unit.

WIRING DIAGRAM

E127578E16
4.052,1.344 4.313,1.521 0.26,0.177 10 false A13 4.542,0.719 4.802,0.896 0.26,0.177 10 false A14 4.552,1.115 4.813,1.292 0.26,0.177 10 false A14 3.583,1.354 3.844,1.531 0.26,0.177 10 false A13 3.125,0.917 3.385,1.094 0.26,0.177 10 false A13 5.448,1.896 5.604,2.073 0.156,0.177 10 false 3 3.594,1.542 3.75,1.719 0.156,0.177 10 false 3 2.667,0.813 2.823,0.99 0.156,0.177 10 false 3 1.854,0.792 2.01,0.969 0.156,0.177 10 false 5 4.25,1.542 4.406,1.719 0.156,0.177 10 false 1 1.844,1.063 2,1.24 0.156,0.177 10 false 1 4.604,0.542 4.76,0.719 0.156,0.177 10 false 1 4.625,0.948 4.781,1.125 0.156,0.177 10 false 2 3.198,0.74 3.354,0.917 0.156,0.177 10 false 2 2.667,1.073 2.823,1.25 0.156,0.177 10 false 2 2.667,2.365 2.823,2.542 0.156,0.177 10 false 3 1.854,2.365 2.01,2.542 0.156,0.177 10 false 5 1.854,2.635 2.01,2.813 0.156,0.177 10 false 1 2.677,2.646 2.833,2.823 0.156,0.177 10 false 2 2.667,3.708 2.823,3.885 0.156,0.177 10 false 3 1.844,3.719 2,3.896 0.156,0.177 10 false 5 1.844,3.99 2,4.167 0.156,0.177 10 false 1 2.677,3.979 2.833,4.156 0.156,0.177 10 false 2 5.406,3.229 5.573,3.406 0.167,0.177 10 false 22 5.469,4.563 5.625,4.74 0.156,0.177 10 false 4 5.427,5.896 7,6.24 1.573,0.344 10 false Air Conditioning Amplifier 0.135,0.104 1.135,0.292 1,0.188 10 false w/ PTC Heater: 5.698,3.385 6.073,3.563 0.375,0.177 10 false PTC2 5.698,4.719 6.073,4.896 0.375,0.177 10 false PTC3 0.583,4.417 0.948,4.594 0.365,0.177 10 false MAIN 0.583,5.125 1.146,5.302 0.563,0.177 10 false FL MAIN 0.74,5.979 1.281,6.198 0.542,0.219 10 false Battery 1.958,3.031 2.656,3.208 0.698,0.177 10 false PTC NO. 2 4.135,1.177 4.292,1.354 0.156,0.177 10 false B 3.656,1.177 3.813,1.354 0.156,0.177 10 false B 3.479,0.927 3.635,1.104 0.156,0.177 10 false B 4.333,0.719 4.49,0.896 0.156,0.177 10 false E 4.344,1.115 4.5,1.292 0.156,0.177 10 false E 1.979,1.448 2.677,1.625 0.698,0.177 10 false PTC NO. 1 3.563,0.375 4.313,0.552 0.75,0.177 10 false PTC Heater 5.74,2.031 6.115,2.208 0.375,0.177 10 false PTC1 1.969,4.385 2.667,4.563 0.698,0.177 10 false PTC NO. 3 0.74,2.656 1.438,2.833 0.698,0.177 10 false PTC NO. 2 0.75,1.104 1.448,1.281 0.698,0.177 10 false PTC NO. 1 0.729,4 1.427,4.177 0.698,0.177 10 false PTC NO. 3 5.417,5.729 5.938,5.938 0.521,0.208 10 false G47

PROCEDURE

1.INSPECT FUSE (PTC NO. 1, PTC NO. 2, PTC NO. 3)
a.

Remove the PTC NO. 1, PTC NO. 2 and PTC NO. 3 H-fuses from the engine room No. 2 relay block.


b.

Measure the resistance of the H-fuses.

Standard resistance:

Below 1 Ω




OK

2.INSPECT PTC HEATER RELAY (Marking: PTC NO. 1, PTC NO. 2, PTC NO. 3)

NG

REPLACE FUSE

2.INSPECT PTC HEATER RELAY (Marking: PTC NO. 1, PTC NO. 2, PTC NO. 3)
A395833E01
2.344,0.792 2.656,0.469 false 2.063,1.771 2.354,1.448 false 1.635,1.115 1.958,1.115 false 2.667,1.115 2.99,1.115 false 0.292,1.323 0.604,1.521 0.313,0.198 10 false 1 0.292,0.781 0.604,0.979 0.313,0.198 10 false 3 1.302,0.781 1.615,0.979 0.313,0.198 10 false 5 1.292,1.313 1.604,1.51 0.313,0.198 10 false 2 1.906,1.74 2.219,1.938 0.313,0.198 10 false 2 2.677,0.333 2.99,0.531 0.313,0.198 10 false 1 1.5,1.031 1.813,1.229 0.313,0.198 10 false 3 3.052,1.031 3.365,1.229 0.313,0.198 10 false 5

a.

Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.


b.

Measure the resistance of the relays.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)




OK

3.CHECK AIR CONDITIONING AMPLIFIER

NG

REPLACE PTC HEATER

3.CHECK AIR CONDITIONING AMPLIFIER
U189841E02
2.656,1.354 2.448,1.979 false 2.375,1.979 2.094,2.802 false 2.51,2.063 2.688,2.802 false 1.813,1.5 2.094,1.667 0.281,0.167 10 false G47 2.583,1.083 3.021,1.281 0.438,0.198 10 false PTC1 2.573,2.823 3.01,3.021 0.438,0.198 10 false PTC2 1.906,2.833 2.344,3.031 0.438,0.198 10 false PTC3

a.

Remove the air conditioning amplifier with its connectors still connected.


b.

Turn the ignition switch on (IG).


c.

When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.


d.

Measure the voltage of the wire harness side connectors.

Standard voltage:
Tester Connection Specified Condition
G47-3 (PTC1) - Body ground 10 to 14 V
G47-22 (PTC2) - Body ground 10 to 14 V
G47-4 (PTC3) - Body ground 10 to 14 V




OK

4.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - PTC HEATER RELAY)

NG

6.CHECK WIRE HARNESS (PTC HEATER RELAY - PTC HEATER)
4.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - PTC HEATER RELAY)
E127594E01
0.139,0.143 2.418,0.324 2.278,0.181 10 Engine Room No. 2 Relay Block: 1.377,2.945 2.891,3.126 1.514,0.181 10 No. 1 PTC Heater Relay 1.205,3.484 2.719,3.665 1.514,0.181 10 No. 2 PTC Heater Relay 0.689,4.011 2.204,4.192 1.514,0.181 10 No. 3 PTC Heater Relay 2.197,2.355 1.613,2.922 false 1.417,2.355 0.96,3.598 false 0.96,3.598 1.171,3.598 false 0.753,2.355 0.38,4.101 false 0.38,4.101 0.591,4.101 false

a.

Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.


b.

Turn the ignition switch on (IG).


c.

When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.


d.

Measure the voltage of the wire harness side connectors.

Standard voltage:
Tester Connection Specified Condition
No. 1 PTC heater relay terminal 1 - Body ground 10 to 14 V
No. 2 PTC heater relay terminal 1 - Body ground 10 to 14 V
No. 3 PTC heater relay terminal 1 - Body ground 10 to 14 V




OK

5.CHECK WIRE HARNESS (PTC HEATER RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS (PTC HEATER RELAY - BODY GROUND)
E127594E01
0.139,0.143 2.418,0.324 2.278,0.181 10 Engine Room No. 2 Relay Block: 1.377,2.945 2.891,3.126 1.514,0.181 10 No. 1 PTC Heater Relay 1.205,3.484 2.719,3.665 1.514,0.181 10 No. 2 PTC Heater Relay 0.689,4.011 2.204,4.192 1.514,0.181 10 No. 3 PTC Heater Relay 2.197,2.355 1.613,2.922 false 1.417,2.355 0.96,3.598 false 0.96,3.598 1.171,3.598 false 0.753,2.355 0.38,4.101 false 0.38,4.101 0.591,4.101 false

a.

Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.


b.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
No. 1 PTC heater relay terminal 2 - Body ground Below 1 Ω
No. 2 PTC heater relay terminal 2 - Body ground Below 1 Ω
No. 3 PTC heater relay terminal 2 - Body ground Below 1 Ω




OK

6.CHECK WIRE HARNESS (PTC HEATER RELAY - PTC HEATER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (PTC HEATER RELAY - PTC HEATER)
E358392E01
4.219,1.427 4.635,1.677 0.417,0.25 0.729,2.406 0.521,2.406 0.521,2.406 1.115,1.344 true 1.323,2.052 1.188,2.052 1.188,2.052 1.667,1.333 true 2.104,1.677 2.26,1.333 true 5.01,2.083 5.188,1.677 true 5.51,2.115 5.385,1.677 true 5.854,2.073 5.563,1.677 true 0.177,0.094 2.604,0.458 2.427,0.365 10 true Engine Room No. 2 Relay Block: 1.969,1.688 3.563,1.958 1.594,0.271 10 false No. 1 PTC Heater Relay 1.385,1.979 3.271,2.26 1.885,0.281 10 false No. 2 PTC Heater Relay 0.813,2.333 2.99,2.604 2.177,0.271 10 false No. 3 PTC Heater Relay 3.99,0.156 5.729,0.396 1.74,0.24 10 false Wire Harness Side: 5.042,0.771 6.25,0.969 1.208,0.198 10 false PTC Heater 4.302,1.469 4.615,1.667 0.313,0.198 10 false A13 4.844,2.115 5.156,2.313 0.313,0.198 10 false B 5.521,2.156 5.833,2.354 0.313,0.198 10 false B 5.854,2.125 6.167,2.323 0.313,0.198 10 false B

a.

Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.


b.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
No. 1 PTC heater relay terminal 3 - A13-2 (B) Below 1 Ω
No. 2 PTC heater relay terminal 3 - A13-3 (B) Below 1 Ω
No. 3 PTC heater relay terminal 3 - A13-1 (B) Below 1 Ω




OK

7.CHECK WIRE HARNESS (BATTERY - PTC HEATER RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK WIRE HARNESS (BATTERY - PTC HEATER RELAY)
E127594E01
0.139,0.143 2.418,0.324 2.278,0.181 10 Engine Room No. 2 Relay Block: 1.377,2.945 2.891,3.126 1.514,0.181 10 No. 1 PTC Heater Relay 1.205,3.484 2.719,3.665 1.514,0.181 10 No. 2 PTC Heater Relay 0.689,4.011 2.204,4.192 1.514,0.181 10 No. 3 PTC Heater Relay 2.197,2.355 1.613,2.922 false 1.417,2.355 0.96,3.598 false 0.96,3.598 1.171,3.598 false 0.753,2.355 0.38,4.101 false 0.38,4.101 0.591,4.101 false

a.

Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.


b.

Measure the voltage of the wire harness side connectors.

Standard voltage:
Tester Connection Specified Condition
No. 1 PTC heater relay terminal 5 - Body ground 10 to 14 V
No. 2 PTC heater relay terminal 5 - Body ground 10 to 14 V
No. 3 PTC heater relay terminal 5 - Body ground 10 to 14 V




OK

8.REPLACE PTC HEATER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE PTC HEATER
a.

After replacing the PTC heater with a normal one, check that the PTC heater function operates normally.

OK:

PTC heater function operates normally.




NG

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

OK

END (PTC HEATER IS FAULTY)