Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM J

AIR CONDITIONING  AIR CONDITIONING SYSTEM  Rear Blower Motor Circuit  


DESCRIPTION

The rear blower motor is operated by signals from the air conditioning amplifier. Rear blower motor speed signals are transmitted in accordance with changes in the duty ratio.

E360153E01
2.875,1.167 3.948,1.396 1.073,0.229 10 false Blower Motor 4.208,0.885 5.281,1.115 1.073,0.229 10 false BLWH 4.531,1.583 5.604,1.813 1.073,0.229 10 false Duty Control 4.135,2.406 5.781,2.635 1.646,0.229 10 false Air Conditioning Amplifier

WIRING DIAGRAM

E127601E09
5.896,0.594 6.354,0.927 0.458,0.333 10 false BLWH 5.896,2.406 6.406,2.74 0.51,0.333 10 false GND2 1.5,0.542 1.708,0.74 0.208,0.198 10 false SI 1.802,0.438 2.01,0.583 0.208,0.146 10 false 3 0.677,1.75 0.833,1.896 0.156,0.146 10 false 6 1.802,1.115 2.01,1.26 0.208,0.146 10 false 1 2.917,3.063 3.125,3.208 0.208,0.146 10 false 1 1.802,1.781 2.01,1.927 0.208,0.146 10 false 2 5.573,2.302 5.781,2.448 0.208,0.146 10 false 20 5.583,0.469 5.833,0.677 0.25,0.208 10 false 22 2.927,2.406 3.104,2.552 0.177,0.146 10 false 2 5.521,2.948 6.208,3.26 0.688,0.313 10 false G48 0.51,2.573 2.25,2.896 1.74,0.323 10 false N16 3.052,2.656 4.271,2.979 1.219,0.323 10 false N14 1.49,1.219 1.698,1.427 0.208,0.208 10 false +B 1.458,1.885 1.719,2.094 0.26,0.208 10 false VM 0.927,1.885 1.292,2.073 0.365,0.188 10 false GND 3.719,1.438 4.323,1.625 0.604,0.188 10 false FL MAIN 4.823,1.771 5.302,1.958 0.479,0.188 10 false Battery 2.156,1.427 2.698,1.604 0.542,0.177 10 false RR A/C 0.135,0.052 1.865,0.354 1.729,0.302 10 false w/ Rear Automatic A/C: 3.042,1.427 3.344,1.604 0.302,0.177 10 false ALT 3.052,2.813 4.271,3.135 1.219,0.323 10 false Rear Blower Motor 0.51,2.729 2.25,3.052 1.74,0.323 10 false Rear Blower Motor Control 5.521,3.125 7.156,3.5 1.635,0.375 10 false Air Conditioning Amplifier

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (R BLOWER MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the intelligent tester main switch ON.


c.

Select the item below in the Active Test, and then check that the rear blower motor operates.

Air conditioning amplifier:
Item Test Details / Display Diagnostic Note
Rear Blower Motor Rear blower motor /
Min.: 0, Max.: 31
-


Result
Result Proceed to
NG (blower motor does not operate) A
NG (blower motor operates but does not change speed) B
OK C



A

2.INSPECT FUSE (RR A/C)

B

6.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BODY GROUND)

C

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT FUSE (RR A/C)
a.

Remove the RR A/C H-fuse from the main body ECU.


b.

Measure the resistance of the H-fuse.

Standard resistance:

Below 1 Ω




OK

3.INSPECT REAR BLOWER MOTOR

NG

REPLACE FUSE

3.INSPECT REAR BLOWER MOTOR
U189860E02
1.76,1.115 2.49,0.49 true 1.635,1.104 0.948,0.396 true 0.813,0.292 0.969,0.469 0.156,0.177 10 false 2 2.542,0.344 2.698,0.521 0.156,0.177 10 false 1 1.563,0.177 1.833,0.354 0.271,0.177 10 false N14

a.

Disconnect the N14 motor connector.


b.

Connect the battery's positive (+) lead to terminal 2 and the negative (-) to terminal 1, then check that the rear blower motor operates smoothly.

OK:

The rear blower motor operates smoothly.



c.

Measure the current of the connector.

Standard current:
Tester Connection Condition Specified Condition
N14-1 - N14-2 Rear blower motor operates 1 to 3 A




OK

4.CHECK WIRE HARNESS (REAR BLOWER MOTOR CONTROL - BODY GROUND)

NG

REPLACE REAR BLOWER MOTOR

4.CHECK WIRE HARNESS (REAR BLOWER MOTOR CONTROL - BODY GROUND)
E127602E01
2.693,1.072 3.019,1.253 0.326,0.181 10 GND 2.073,1.605 2.644,1.203 false

a.

Disconnect the N16 rear motor control connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
N16-6 (GND) - Body ground Below 1 Ω




OK

5.CHECK WIRE HARNESS (REAR BLOWER MOTOR CONTROL - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS (REAR BLOWER MOTOR CONTROL - BATTERY)
E127602E02
0.38,1.677 0.570,1.859 0.191,0.181 10 +B 1.443,1.366 0.649,1.73 false

a.

Disconnect the N16 rear motor control connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
N16-1 (+B) - Body ground Ignition switch on (IG) 10 to 14 V




OK

6.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BODY GROUND)
U189862E02
0.438,2.458 0.688,3.052 false 0.594,2.458 1.333,3.052 false 0.719,3.021 1.135,3.198 0.417,0.177 10 false BLWH 0.156,0.063 1.438,0.25 1.281,0.188 10 false Wire Harness Side: 0.927,0.521 2.5,0.698 1.573,0.177 10 false Air Conditioning Amplifier 0.531,0.969 0.813,1.146 0.281,0.177 10 false G48 1.385,3.01 1.802,3.188 0.417,0.177 10 false GND2

a.

Disconnect the G48 amplifier connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
G48-22 (BLWH) - G48-20 (GND2) Ignition switch on (IG)
Blower switch OFF
4.5 to 5.5 V




OK

7.CHECK AIR CONDITIONING AMPLIFIER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK AIR CONDITIONING AMPLIFIER
E358394E01
0.333,0.333 0.75,0.583 0.417,0.25 0.552,1.719 0.438,1.167 true 1.354,1.719 0.563,1.167 true 1.073,0.271 2.802,0.552 1.729,0.281 10 false Air Conditioning Amplifier 1.094,4.365 2.365,4.583 1.271,0.219 10 false 500 μsec./DIV. 0.406,0.375 1.042,0.646 0.635,0.271 10 false G48 0.51,1.75 1.146,2.021 0.635,0.271 10 false BLWH 1.323,1.74 1.958,2.01 0.635,0.271 10 false GND2 0.115,2.031 0.75,2.302 0.635,0.271 10 false Waveform: 0.427,2.365 2.792,2.719 2.365,0.354 10 false Rear Blower Motor Control Signal 2.656,2.604 3.292,2.875 0.635,0.271 10 false 1 V/DIV. 2.813,4.052 3.281,4.323 0.469,0.271 10 false GND

a.

Remove the air conditioning amplifier with its connectors still connected.


b.

Check the waveform of the amplifier connector.

OK:

Waveform is as shown in the illustration.


HINT:

The waveform varies with the blower level.


Item Content
Tester Connection BLWH (G48-22) - GND2 (G48-20)
Tool Setting 1 V/DIV., 500 μsec./DIV.
Condition Ignition switch on (IG)
Blower switch LO



OK

REPLACE REAR BLOWER MOTOR

NG

REPLACE AIR CONDITIONING AMPLIFIER