Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM D

AIR CONDITIONING  AIR CONDITIONING SYSTEM  CHECK MODE PROCEDURE  


PANEL DIAGNOSIS (INDICATOR CHECK)


a.

Turn the engine switch off.


b.

Press and hold the A/C control AUTO switch and Recirculation / Fresh switch simultaneously, and turn the engine switch on (IG). Continue holding the 2 switches until panel diagnosis mode begins.

E253818E02
0.623,0.117 2.769,0.276 2.145,0.159 10 Front A/C Control Panel (for RHD) 4.392,0.117 6.503,0.276 2.111,0.159 10 Front A/C Control Panel (for LHD)


c.
E127586E01
0.712,0.34 1.292,0.522 0.581,0.181 10 1 second 1.744,0.34 2.324,0.522 0.581,0.181 10 1 second 0.186,0.974 0.412,1.155 0.225,0.181 10 ON 0.186,1.418 0.481,1.599 0.295,0.181 10 OFF

Check that all indicators and the display area are turned on and off 4 times in succession at 1 second intervals.

E253819E01
0.82,0.26 2.965,0.419 2.145,0.159 10 Front A/C Control Panel (for RHD) 4.182,0.26 6.293,0.419 2.111,0.159 10 Front A/C Control Panel (for LHD) 2.515,3.099 4.649,3.258 2.134,0.159 10 Rear Automatic A/C Control Panel

HINT:

After the indicator check is completed, the system automatically enters sensor check mode.



d.

Press the OFF switch to terminate panel diagnosis.



PANEL DIAGNOSIS (SENSOR CHECK)


a.

Perform the indicator check.

HINT:

After the indicator check is completed, the system automatically enters sensor check mode.



b.

Press the Recirculation / Fresh switch to enter actuator check mode.


c.

After the actuator check is completed, press the AUTO switch to enter sensor check mode.

NOTICE:

The sensor check must be performed again after the actuator check is completed because sensor check mode, which starts automatically after the indicator check, cannot automatically detect all malfunctions.



d.

Check the sensor check results displayed on the set temperature display.

E253820E02
0.825,0.116 2.971,0.275 2.145,0.159 10 Front A/C Control Panel (for RHD) 4.202,0.116 6.313,0.275 2.111,0.159 10 Front A/C Control Panel (for LHD)

Results Code Display
Current malfunction Blinks
Past malfunction Blinks

HINT:
·

The illustration shows the display when DTC 21 is output.

·

When 2 or more DTCs are output, the DTCs are displayed in ascending numerical order.

·

In cases with 2 or more DTCs, if they are difficult to read, press the DEF switch to activate the step operation and display them one by one.

·

The DTCs are displayed in ascending numerical order as the DEF switch is pressed.




e.

When any DTCs are displayed, refer to the DTC chart (see page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).


f.

Press the OFF switch to terminate the panel diagnosis.

HINT:

Pressing the Recirculation / Fresh switch returns the system to actuator check mode.




PANEL DIAGNOSIS (CLEAR DTC)


a.

Inspect and repair or replace the malfunctioning parts.


b.

Clear the DTCs.

E253821E01
0.813,0.12 2.958,0.279 2.145,0.159 10 Front A/C Control Panel (for RHD) 4.203,0.12 6.314,0.279 2.111,0.159 10 Front A/C Control Panel (for LHD)

i.

During sensor check mode, press the Fr DEF switch and Rr DEF switch simultaneously.

HINT:

DTCs can be cleared by removing the ECU-B fuse from the engine room No. 1 relay block for more than 60 seconds.




c.

Perform the sensor check and confirm that normal code 00 is displayed.



PANEL DIAGNOSIS (ACTUATOR CHECK)


a.

Start the engine and warm it up.


b.

Perform the indicator check.


c.

When the sensor check is started after the indicator check, press the Recirculation / Fresh switch to start the actuator check.

HINT:

Perform the actuator check with the engine running.



d.
E127586E01
0.712,0.34 1.292,0.522 0.581,0.181 10 1 second 1.744,0.34 2.324,0.522 0.581,0.181 10 1 second 0.186,0.974 0.412,1.155 0.225,0.181 10 ON 0.186,1.418 0.481,1.599 0.295,0.181 10 OFF

Check the temperature and blower levels by hand at each step while the actuator check proceeds from step 0 to 9 at 1 second intervals (continuous operation).

E253822E01
0.821,0.256 2.966,0.415 2.145,0.159 10 Front A/C Control Panel (for RHD) 4.211,0.256 6.322,0.415 2.111,0.159 10 Front A/C Control Panel (for LHD) 2.565,3.019 4.693,3.179 2.128,0.159 10 Rear Automatic A/C Control Panel

HINT:

Each step number is displayed on the set temperature display.



e.

To display step numbers one by one manually, press the Fr DEF switch to activate step operation. The step number changes each time the Fr DEF switch is pressed.

HINT:
·

Each step number blinks at 1 second intervals during the step operation.

·

The illustration shows the display when step number 5 is displayed.




f.

Press the OFF switch to terminate the panel diagnosis.

HINT:

Pressing the AUTO switch returns panel diagnosis back to sensor check mode.


Step No.
(Front display)
Blower Level Front Air Mix Damper Air Flow Vent Air Inlet Damper Cool Air By-pass Compressor Rear Air Mix Damper Rear Air Flow Vent Rear Blower Level
0 0 0%
(MAX COLD)
FACE FRESH - OFF 0 Rr FACE 0
1 1 0%
(MAX COLD)
FACE FRESH - OFF 0 Rr FACE 1
2 17 0%
(MAX COLD)
FACE RECIRCULATION / FRESH - ON 0 Rr FACE 17
3 17 0%
(MAX COLD)
FACE RECIRCULATION - ON 0 Rr FACE 17
4 17 50% BI-LEVEL RECIRCULATION - ON 50 Rr BI-LEVEL 17
5 17 50% BI-LEVEL RECIRCULATION - ON 50 Rr BI-LEVEL 17
6 17 50% FOOT FRESH - ON 50 Rr FOOT 17
7 17 100%
(MAX HOT)
FOOT FRESH - ON 100 Rr FOOT 17
8 17 100%
(MAX HOT)
FOOT/DEF FRESH - ON 100 Rr FOOT 17
9 31 100%
(MAX HOT)
DEF FRESH - ON 100 Rr FOOT 31