READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators, and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Read the Data List by following the prompts on the tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Room Temperature Sensor | Room temperature sensor /
Min.: -6.5°C (20.3°F) Max.: 57.25°C (135.05°F) |
Actual cabin temperature is displayed | - |
| Ambient Temp Sensor | Ambient temperature sensor /
Min.: -23.3°C (-9.94°F) Max.: 65.95°C (150.71°F) |
Actual ambient temperature is displayed | - |
| Adjusted Ambient Temp | Adjusted ambient temperature /
Min.: -30.8°C (-23.44°F) Max.: 50.8°C (123.44°F) |
- | - |
| Evaporator Fin Thermistor | Evaporator temperature sensor /
Min.: -29.7°C (-21.46°F) Max.: 59.55°C (139.19°F) |
Actual evaporator temperature is displayed | - |
| Evaporator Target Temp | Evaporator target temperature /
Min.: -327.68°C (-557.82°F) Max.: 327.67°C (621.81°F) |
Evaporator target temperature is displayed | - |
| Solar Sensor (D Side) | Driver side solar sensor /
Min.: 0, Max.: 255 |
Driver side solar sensor value increases as brightness increases | - |
| Solar Sensor (P Side) | Passenger side solar sensor /
Min.: 0, Max.: 255 |
Passenger side solar sensor value increases as brightness increases | - |
| Engine Coolant Temp | Engine coolant temperature sensor /
Min.: 1.3°C (34.34°F) Max.: 90.55°C (194.99°F) |
Actual engine coolant temperature is displayed | - |
| Set Temperature (D Side) | Driver side set temperature /
Min.: 0°C (32°F) Max.: 30°C (86°F) |
Driver side actual set temperature is displayed | - |
| Set Temperature (P Side) | Passenger side set temperature /
Min.: 0°C (32°F) Max.: 30°C (86°F) |
Passenger side actual set temperature is displayed | - |
| Blower Motor Speed Level | Blower motor speed level /
Min.: 0, Max.: 31 |
Increases in range between 0 and 31 as blower motor speed increases | - |
| Regulator Pressure Sensor | Regulator pressure sensor /
Min.: 0 kgf/cm2G Max.: 38.25 kgf/cm2G |
Actual regulator pressure is displayed | - |
| Regulator Control Current | Regulator control current /
Min.: 0 A Max.: 0.997 A |
Value changes between 0 A and 0.997 A in accordance with compressor and magnetic clutch operation | - |
| Room Temp Sensor (Rear) | Rear room temperature sensor /
Min.: -6.5°C (20.3°F) Max.: 57.25°C (135.05°F) |
Actual rear cabin temperature is displayed | - |
| Evap Temp Sensor (Rear) | Rear evaporator temperature sensor /
Min.: -29.7°C (-21.46°F) Max.: 59.55°C (139.19°F) |
Actual rear evaporator temperature is displayed | - |
| Blower Motor Level (Rear) | Rear blower motor speed level /
Min.; 0, Max.: 31 |
Increases in range between 0 and 31 as rear blower motor speed increases | - |
| Air Outlet Servo Pulse (R) | Rear side air outlet servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Air Mix Servo Targ Pulse(R) | Rear side air mix servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Air Mix Servo Targ Pulse(R) | Rear side air mix servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Air Mix Servo Targ Pulse(P) | Passenger side air mix control servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Air Outlet Servo Pulse (D) | Air outlet control servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Air Inlet Damper Targ Pulse | Air inlet control servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Outside Air Mode Auto Switch Function* | Outside air mode auto switch function
ON or OFF |
Customized value displayed | - |
| Number of Trouble Codes | Number of trouble codes /
Min.: 0, Max.: 255 |
Number of DTCs displayed | - |
*: except China, G. C. C. countries
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Perform the Active Test by following the prompts on the tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Blower Motor | Blower motor | Min.: 0, Max.: 31 | - |
| Magnetic Clutch Relay | Magnetic clutch relay | OFF, ON | - |
| Defogger Relay (Rear) | Defogger relay (Rear) | OFF, ON | - |
| Heater Active Level | PTC heater | Min.: 0, Max.: 3 | - |
| Air Mix Servo Targ Pulse(D) | Air mix control servo motor pulse (D side) | Min.: 0, Max.: 255 | - |
| Air Mix Servo Targ Pulse(P) | Air mix control servo motor pulse (P side) | Min.: 0, Max.: 255 | - |
| Air Outlet Servo Pulse (D) | Air outlet control servo motor pulse (D side) | Min.: 0, Max.: 255 | - |
| Air Inlet Damper Targ Pulse | Air inlet control servo motor target pulse | Min.: 0, Max.: 255 | - |
| Rear Blower Motor | Rear blower motor | Min.: 0, Max.: 31 | - |
| Rear Air Mix Servo Targ Pulse | Rear air mix servo motor pulse | Min.: 0, Max.: 255 | - |
| Ion Generator* | No. 2 ion generator sub-assembly | OFF, ON | - |
*: w/ Ion Generator Assembly