The air conditioning harness assembly connects the No. 1 air conditioning amplifier assembly and the servos. The No. 1 air conditioning amplifier assembly supplies power and sends operation instructions to each servo through the air conditioning harness assembly. Each servo sends damper position information to the No. 1 air conditioning amplifier assembly.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1497/97 | Communication line error or open | ·
Air conditioning harness assembly ·
Rear air conditioning harness assembly ·
Servo motors ·
No. 1 air conditioning amplifier assembly |
w/ Rear Automatic Air Conditioning System
w/ Rear Manual Air Conditioning System
Inspect the fuse for circuits related to this system before performing the following inspection procedure.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Data List.
Check the operation by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Air Mix Pulse-D | Driver side air mix servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Air Mix Pulse-P | Passenger side air mix servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Air Out Pulse-D | Driver side air outlet servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| A/I Damp Targ Pls | Air inlet damper target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Air Mix Pulse-R | Rear side air mix servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
| Air Out Pulse-R | Rear side air outlet servo motor target pulse /
Min.: 0, Max.: 255 |
Customized value displayed | - |
Pulse value for each damper servo motor changes in accordance with corresponding switch operation
According to the test, proceed to the next step.
| Result | Proceed to |
|---|---|
| One of the front air conditioner damper servo motors is malfunctioning | A |
| All of the front air conditioner damper servo motors are malfunctioning | B |
| One of the rear air conditioner damper servo motors is malfunctioning | C |
| All of the rear air conditioner damper servo motors are malfunctioning | D |
A
B
C
D
According to the test, proceed to the next step.
| Result | Proceed to |
|---|---|
| Only the air mix damper servo motor (for driver side) is malfunctioning | A |
| Only the air mix damper servo motor (for passenger side) is malfunctioning | B |
| Only the air inlet control servo motor is malfunctioning | C |
| Only the air outlet control servo motor is malfunctioning | D |
A
B
C
D
Replace the air mix control servo motor (for driver side).
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the air mix control servo motor (for passenger side).
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the air inlet control servo motor.
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the air outlet control servo motor.
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the air conditioning harness assembly.
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or a known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
According to the test, proceed to the next step.
| Result | Proceed to |
|---|---|
| Only the rear air mix control servo motor is malfunctioning | A |
| Only the rear air outlet control servo motor is malfunctioning | B |
A
B
Replace the rear air mix control servo motor.
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the air outlet control servo motor.
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Disconnect the rear air conditioning harness assembly connector.
Disconnect the No. 1 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G48-23 (RBBU) - N17-4 (RBBU) | Always | Below 1 Ω |
| G48-1 (RBUS) - N17-3 (RBUS) | Always | Below 1 Ω |
| G48-21 (RBUG) - N17-2 (RBUG) | Always | Below 1 Ω |
| G48-23 (RBBU) - Body ground | Always | 10 kΩ or higher |
| G48-1 (RBUS) - Body ground | Always | 10 kΩ or higher |
| G48-21 (RBUG) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the rear air conditioning harness assembly.
Since the rear air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the rear air conditioning harness assembly with a new or a known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Disconnect the No. 1 air conditioning amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G47-21 (B) - Body ground | Always | 11 to 14 V |
| G48-24 (+B2) - Body ground*1 | Always | 11 to 14 V |
*1: w/ Rear Automatic Air Conditioning System
OK
NG