Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM J

AIR CONDITIONING  AIR CONDITIONING SYSTEM  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the A/C amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the A/C amplifier. Then, the MGC relay turns on to operate the magnetic clutch.

WIRING DIAGRAM

E124490E07
0.984,3.029 1.762,3.201 0.777,0.172 10 RH ECU-IG 2.605,3.284 4.122,3.458 1.516,0.173 10 from RH-IG Relay 1 2.965,4.211 3.264,4.385 0.299,0.174 10 D49 2.965,4.406 4.111,4.767 1.146,0.361 10 A/C Compressor (Magnetic Clutch) 1.147,0.544 4.378,0.721 3.230,0.177 10 Engine Room No. 2 Relay Block and Junction Block 1.684,1.48 1.804,1.644 0.120,0.164 10 2 1.684,1.989 1.804,2.153 0.120,0.164 10 2 3.753,1.48 3.873,1.644 0.120,0.164 10 2 3.753,1.989 3.873,2.153 0.120,0.164 10 2 2.483,0.982 3.056,1.147 0.572,0.165 10 MG CLT 3.17,1.38 3.299,1.554 0.129,0.174 10 3 2.271,1.38 2.387,1.547 0.117,0.167 10 5 3.17,1.895 3.298,2.077 0.129,0.182 10 2 2.271,1.895 2.387,2.062 0.116,0.167 10 1 4.721,3.831 4.858,4.006 0.137,0.175 10 3 4.717,4.093 5.078,4.260 0.361,0.166 10 MG+ 4.283,4.503 4.423,4.667 0.139,0.163 10 A 4.533,4.278 4.656,4.452 0.123,0.173 10 1 6.022,0.328 6.889,0.519 0.867,0.191 10 A/C Amplifier 6.101,1.978 6.507,2.156 0.406,0.178 10 MGC 5.674,1.995 5.980,2.155 0.305,0.160 10 G47 5.723,1.772 5.913,1.932 0.190,0.160 10 20

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B
(see page (Click here))




A

2.READ VALUE USING INTELLIGENT TESTER

B

2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the intelligent tester main switch on.


c.

Turn the A/C switch on and off.


d.

Select the item below in the Data List, and read the display on the intelligent tester.

Data List / Engine:
Tester Display Measure Item/Range Normal Condition Diagnostic Note
A/C Signal
(A/C Signal)
A/C signal / ON or OFF ON: A/C ON
OFF: A/C OFF
-

OK:

The display is as specified in the normal condition column.




OK

3.INSPECT FUSE (RH ECU-IG)

NG

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

3.INSPECT FUSE (RH ECU-IG)
a.

Remove the RH ECU-IG fuse from the instrument panel junction block RH.


b.

Measure the resistance of the fuse.

Standard resistance:
Tester Item Condition Specified Condition
RH ECU-IG Always Below 1 Ω



c.

Reconnect the RH ECU-IG fuse to the instrument panel junction block RH.



OK

4.INSPECT RELAY (MG CLT)

NG

REPLACE FUSE (RH ECU-IG)

4.INSPECT RELAY (MG CLT)
a.
B426341E06
2.625,0.75 2.927,0.5 false 2.469,1.135 2.896,0.969 false 2.469,1.625 2.906,1.458 false 2.031,0.708 1.719,0.469 false 0.24,0.76 0.458,0.979 0.219,0.219 10 false 3 0.229,1.323 0.448,1.542 0.219,0.219 10 false 2 1.198,0.76 1.417,0.979 0.219,0.219 10 false 5 1.177,1.323 1.396,1.542 0.219,0.219 10 false 1 1.563,0.354 1.781,0.573 0.219,0.219 10 false 1 2.99,0.875 3.208,1.094 0.219,0.219 10 false 5 2.979,1.375 3.198,1.594 0.219,0.219 10 false 3 2.969,0.417 3.188,0.635 0.219,0.219 10 false 2

Remove the MG CLT relay from the engine room No. 2 relay block and junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)



c.

Install the MG CLT relay to the engine room No. 2 relay block and junction block.



OK

5.CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - BATTERY)

NG

REPLACE RELAY (MG CLT)

5.CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - BATTERY)
a.
U189816E02
1.333,2.115 0.99,2.771 false 0.75,2.792 1.125,2.948 0.375,0.156 10 false MGC 0.063,0.375 1.667,0.552 1.604,0.177 10 false Air Conditioning Amplifier 0.063,0.021 1.385,0.177 1.323,0.156 10 false Wire Harness Side: 1.698,0.875 1.99,1.031 0.292,0.156 10 false G47

Disconnect the connector from the A/C amplifier.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G47-20 (MGC) - Body ground Ignition switch off Below 1 V
G47-20 (MGC) - Body ground Ignition switch on (IG) 10 to 14 V




OK

6.INSPECT AIR CONDITIONING AMPLIFIER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (A/C AMPLIFIER - BATTERY)

6.INSPECT AIR CONDITIONING AMPLIFIER
a.
U189818E02
1.344,1.479 1.344,2.333 false 1.177,2.354 1.542,2.531 0.365,0.177 10 false MGC 0.052,0.385 1.656,0.563 1.604,0.177 10 false Air Conditioning Amplifier 0.052,0.042 1.375,0.198 1.323,0.156 10 false Wire Harness Side: 1.823,0.865 2.115,1.021 0.292,0.156 10 false G47

Reconnect the connector to the A/C amplifier.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G47-20 (MGC) - Body ground Ignition switch on (IG)
A/C switch: OFF
10 to 14 V
G47-20 (MGC) - Body ground Ignition switch on (IG)
A/C switch: ON
Below 1 V




OK

7.INSPECT A/C COMPRESSOR

NG

REPLACE AIR CONDITIONING AMPLIFIER

7.INSPECT A/C COMPRESSOR
a.
U189797E02
1.708,1.344 1.708,1.844 false 0.052,0.052 2.729,0.271 2.677,0.219 10 false A/C Compressor Connector Front View: 1.563,1.865 1.938,2.052 0.375,0.188 10 false MG+ 0.76,1.01 1.052,1.167 0.292,0.156 10 false D49

Disconnect the connector from the A/C compressor.


b.
U189820E01
0.065,0 1.622,0.334 1.557,0.334 10 Magnetic Clutch Connector Front View: 0.884,1.34 1.026,1.496 0.142,0.156 10 A

Disconnect the connector from the magnetic clutch.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D49-3 (MG+) - A-1 Always Below 1 Ω
D49-3 (MG+) - Body ground Always 10 kΩ or higher




OK

8.INSPECT MAGNETIC CLUTCH

NG

REPLACE A/C COMPRESSOR

8.INSPECT MAGNETIC CLUTCH
a.
U189804E02
0.094,0.063 0.823,0.823 0.729,0.76 10 false Magnetic Clutch Connector Front View: 2.417,0.813 2.583,1 0.167,0.188 10 false A

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A-1 - Body ground 20°C (68°F) 3.8 to 4.2 Ω



b.

When connector terminal A-1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound can be heard, and 2) the magnetic clutch's hub and rotor lock.



OK

9.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 R/B AND J/B - BATTERY)

NG

REPLACE MAGNETIC CLUTCH

9.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 R/B AND J/B - BATTERY)
a.
E145184E15
0.063,0.104 2.542,0.521 2.479,0.417 10 true Engine Room No. 2 Relay Block and Junction Block: 2.156,1.302 3.104,1.5 0.948,0.198 10 false MG CLT Relay

Remove the MG CLT relay from the engine room No. 2 relay block and junction block.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Specified Condition
Relay block MG CLT relay terminal 5 - Body ground 10 to 14 V
Relay block MG CLT relay terminal 1 - Body ground 10 to 14 V




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM NO. 2 R/B AND J/B - A/C COMPRESSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM NO. 2 R/B AND J/B - BATTERY)