Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292180 AIR CONDITIONING SYSTEM J

AIR CONDITIONING  AIR CONDITIONING SYSTEM  Air Conditioning Control Panel does not Operate  


DESCRIPTION

for LHD

This circuit consists of the air conditioning control and the air conditioning amplifier. When the air conditioning control is operated, signals are transmitted to the air conditioning amplifier through the LIN communication system.

If the LIN communication system malfunctions, the air conditioning amplifier does not operate even if the air conditioning control is operated.

for RHD

This circuit consists of the air conditioner panel sub-assembly and the air conditioning amplifier. When the air conditioner panel sub-assembly is operated, signals are transmitted to the air conditioning amplifier through the LIN communication system.

If the LIN communication system malfunctions, the air conditioning amplifier does not operate even if the air conditioner panel sub-assembly is operated.

WIRING DIAGRAM

E127596E09
5.302,0.844 5.615,1.021 0.313,0.177 10 false LIN1 1.625,0.844 1.938,1.021 0.313,0.177 10 false LIN1 1.656,1.365 1.906,1.542 0.25,0.177 10 false IG+ 1.604,1.906 1.927,2.083 0.323,0.177 10 false GND 3.896,1.406 4.708,1.844 0.813,0.438 10 false from RH-IG 1 Relay 2.75,1.563 3.49,1.74 0.74,0.177 10 false RH ECU-IG 0.26,0.146 1,0.323 0.74,0.177 10 false for LHD: 5.198,2.49 6.771,2.833 1.573,0.344 10 false G47 0.854,2.49 2.333,2.833 1.479,0.344 10 false G37 1.302,3.271 2.917,3.448 1.615,0.177 10 false : LIN Communication Line 5,0.74 5.167,0.917 0.167,0.177 10 false 37 1.99,0.729 2.146,0.906 0.156,0.177 10 false 3 1.99,1.281 2.146,1.458 0.156,0.177 10 false 1 1.99,1.833 2.146,2.01 0.156,0.177 10 false 6 0.854,2.656 2.333,3 1.479,0.344 10 false Air Conditioning Control 5.219,2.667 6.792,3.01 1.573,0.344 10 false Air Conditioning Amplifier

E347503E06
0.188,0.094 0.917,0.302 0.729,0.208 10 false for RHD: 1.583,0.708 1.969,0.906 0.385,0.198 10 false LIN1 2.802,1.333 3.417,1.531 0.615,0.198 10 false ECU-B3 4.979,0.531 5.229,0.719 0.25,0.188 10 false 37 3.896,1.188 4.74,1.385 0.844,0.198 10 false from Battery 5.281,0.719 5.667,0.917 0.385,0.198 10 false LIN1 5.229,3.188 5.615,3.385 0.385,0.198 10 false G47 3.896,1.656 5.188,1.854 1.292,0.198 10 false from RH-IG 1 Relay 3.896,2.188 5.188,2.385 1.292,0.198 10 false from ACC Relay 5.229,3.344 6.896,3.542 1.667,0.198 10 false Air Conditioning Amplifier 0.208,2.969 0.719,3.167 0.51,0.198 10 false G120 0.208,3.135 2.573,3.385 2.365,0.25 10 false Air Conditioner Panel Sub-assembly 1.292,3.813 3.021,4.073 1.729,0.26 10 false : LIN Communication Line 2.74,2.333 3.531,2.531 0.792,0.198 10 false ECU-ACC 2.688,1.813 3.51,2.01 0.823,0.198 10 false RH ECU-IG 2.063,0.542 2.229,0.729 0.167,0.188 10 false 8 2.063,1.01 2.229,1.198 0.167,0.188 10 false 1 2.063,1.49 2.229,1.677 0.167,0.188 10 false 2 2.063,2.01 2.229,2.198 0.167,0.188 10 false 5 2.063,2.448 2.229,2.635 0.167,0.188 10 false 4 1.698,1.208 1.969,1.406 0.271,0.198 10 false +B 1.646,1.688 1.99,1.833 0.344,0.146 10 false IG+ 1.583,2.177 1.927,2.323 0.344,0.146 10 false ACC 1.573,2.646 1.917,2.792 0.344,0.146 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CONFIRM MODEL
Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL - BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE, GROUND)
2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL - BODY GROUND)
a.

Disconnect the G37 air conditioning control connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Connection Specified Condition
G37-6 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL - BATTERY)
a.

Disconnect the G37 air conditioning control connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
G37-6 (GND) - G37-1 (IG+) Engine switch on (IG) 10 to 14 V
Engine switch off Below 1 V




OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONING CONTROL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONING CONTROL)
a.

Disconnect the G37 control connector.


b.

Disconnect the G47 amplifier connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Condition Specified Condition
G47-37 (LIN1) - G37-3 (LIN1) Always Below 1 Ω
G47-37 (LIN1) or G37-3 (LIN1) - Body ground Always 10 kΩ or higher




OK

5.REPLACE AIR CONDITIONING CONTROL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE AIR CONDITIONING CONTROL
a.

Replace the air conditioning control with a new or properly functioning one.


b.

Operate the air conditioning control to check that it functions properly.

OK:

Air conditioning control function operates normally.


Result
Result Proceed to
Air conditioning control malfunctions A
Air conditioning control functions properly B



A

REPLACE AIR CONDITIONING AMPLIFIER

B

END (AIR CONDITIONING CONTROL ASSEMBLY IS FAULTY)

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE, GROUND)
a.

Disconnect the air conditioner panel sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G120-4 (ACC) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) 10 to 14 V
G120-2 (IG+) - Body ground Engine switch off Below 1 V
Engine switch on (IG) 10 to 14 V
G120-1 (+B) - Body ground Engine switch off 10 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G120-4 (GND) - Body ground Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONER PANEL SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONER PANEL SUB-ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G120-8 (LIN1) - G47-37 (LIN1) Always Below 1 Ω
G120-8 (LIN1) or G47-37 (LIN1) - Body ground Always 10 kΩ or higher




OK

8.REPLACE AIR CONDITIONER PANEL SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE AIR CONDITIONER PANEL SUB-ASSEMBLY
a.

Replace the air conditioner panel sub-assembly with a new or a known good one (See page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING PANEL(for RHD)>REMOVAL).

OK:

The air conditioner panel sub-assembly operation returns to normal.




OK

END (AIR CONDITIONER PANEL SUB-ASSEMBLY)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE