Home › Vehicle Interior › THEFT DETERRENT › THEFT DETERRENT SYSTEM
RM24M0E _58 Vehicle Interior _059585 THEFT DETERRENT _0292193 THEFT DETERRENT SYSTEM U

THEFT DETERRENT  THEFT DETERRENT SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)


B459608E02
2.667,4.833 3.083,5.083 0.417,0.25 3.333,4.833 3.75,5.083 0.417,0.25 4.25,4.833 4.667,5.083 0.417,0.25 5.417,4.833 5.833,5.083 0.417,0.25 1.208,4.833 1.625,5.083 0.417,0.25 0.469,0.125 2.365,0.417 1.896,0.292 10 false Vehicle Front Side: 5.5,0.125 6.802,0.406 1.302,0.281 10 false Vehicle Rear Side: 6.083,1.542 6.542,1.75 0.458,0.208 10 false G57 1.344,4.885 1.802,5.094 0.458,0.208 10 false 4K 6.073,2.073 6.531,2.281 0.458,0.208 10 false G58 5.688,2.438 6.146,2.646 0.458,0.208 10 false 4K 6.073,2.49 6.531,2.698 0.458,0.208 10 false G59 6.073,2.802 6.531,3.01 0.458,0.208 10 false G60 2.75,4.875 3.208,5.083 0.458,0.208 10 false G60 3.417,4.875 3.875,5.083 0.458,0.208 10 false G59 4.333,4.885 4.792,5.094 0.458,0.208 10 false G58 5.5,4.875 5.958,5.083 0.458,0.208 10 false G57

a.

Disconnect the 4K ECU connector.


b.

Measure the voltage and resistance of the wire harness side connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
4K-2 - Body ground Y - Body ground Horn signal Horn sounding 10 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the 4K ECU connector.


d.

Measure the voltage of the connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
AM1 (G57-6) - Body ground G - Body ground +B power supply Always 10 to 14 V
GND1 (G59-1) - Body ground W-B - Body ground Ground Always Below 1 Ω
HAZ (G59-4) - Body ground GR - Body ground Hazard warning light signal System is in alarm sounding state Pulse generation

If the result is not as specified, the ECU may have a malfunction.



CHECK CERTIFICATION ECU


U185919E02
2.083,0.188 2.406,0.385 0.323,0.198 10 false G29 5.135,0.188 5.458,0.385 0.323,0.198 10 false G30

a.

Disconnect the G29 and G30 ECU connectors.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
G29-1 (+B) - Body ground O - Body ground Battery power supply (ECU) Always 10 to 14 V
G29-17 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
G30-24 (HSW) - Body ground LG - Body ground Engine hood courtesy switch signal Engine hood closed 10 kΩ or higher
G30-24 (HSW) - Body ground LG - Body ground Engine hood courtesy switch signal Engine hood open Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the G29 and G30 ECU connectors.


d.

Measure the voltage of the connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
IG (G29-18) - Body ground Y - Body ground Ignition power supply Always 10 to 14 V
IND (G29-2) - Body ground V - Body ground Security indicator signal Security indicator illuminates (illuminates only for 30 sec. in alarm sounding state, (it is blinking when system is in armed state)) 6 to 8 V
SH- (G30-20) - Body ground L - Body ground Security horn signal Security horn is sounding (theft deterrent system is in alarm sounding state) Pulse generation

If the result is not as specified, the junction block may have a malfunction.