Home › Vehicle Interior › THEFT DETERRENT › THEFT DETERRENT SYSTEM
RM24M0E _58 Vehicle Interior _059585 THEFT DETERRENT _0292193 THEFT DETERRENT SYSTEM J

THEFT DETERRENT  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is built into the hood lock. This switch turns OFF when the engine hood is opened and turns ON when the engine hood is closed.


WIRING DIAGRAM

B144885E01
2.526,2.421 4.508,2.771 1.982,0.350 10 Security Courtesy Switch (Engine Hood Courtesy Switch) 5.503,2.942 6.624,3.125 1.121,0.184 10 Certification ECU 5.647,1.927 6.021,2.083 0.374,0.156 10 HSW 5.503,2.79 5.825,2.939 0.323,0.149 10 G30 2.721,2.033 2.884,2.210 0.163,0.178 10 1 3.658,2.033 3.821,2.210 0.163,0.178 10 2 5.353,2.033 5.537,2.210 0.184,0.178 10 24 2.526,2.284 2.757,2.441 0.231,0.157 10 B8

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE HOOD COURTESY SWITCH)
a.

Check the Data List for proper functioning of the engine hood courtesy switch.

Certification ECU:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
HOOD CTY SW Hood courtesy switch /
ON or OFF
ON: Engine hood is open
OFF: Engine hood is closed
-

OK:

ON (engine hood is open) appears on screen.




NG

2.INSPECT ENGINE HOOD COURTESY SWITCH

OK

REPLACE CERTIFICATION ECU

2.INSPECT ENGINE HOOD COURTESY SWITCH
B119751E08
0.156,0.104 1.427,0.281 1.271,0.177 10 false Not Pushed (OFF) 0.24,0.979 0.74,1.313 0.5,0.333 10 false Pushed (ON)

a.

Remove the courtesy switch from the hood lock.


b.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 Pushed (ON) Below 1 Ω
1 - 2 Not pushed (OFF) 10 kΩ or higher




OK

3.CHECK WIRE HARNESS (CERTIFICATION ECU AND BODY GROUND - ENGINE HOOD COURTESY SWITCH)

NG

REPLACE ENGINE HOOD COURTESY SWITCH

3.CHECK WIRE HARNESS (CERTIFICATION ECU AND BODY GROUND - ENGINE HOOD COURTESY SWITCH)
U185938E03
2.281,1.958 2.167,2.365 false 0.25,0.198 1.635,0.354 1.385,0.156 10 false Wire Harness Side: 1.198,0.802 2.313,0.958 1.115,0.156 10 false Certification ECU 0.333,0.896 0.646,1.063 0.313,0.167 10 false G30 0.823,3.458 1.052,3.625 0.229,0.167 10 false B8 0.771,2.771 2.677,2.938 1.906,0.167 10 false Engine Hood Courtesy Switch 1.938,2.396 2.292,2.552 0.354,0.156 10 false HSW

a.

Disconnect the G30 ECU connector.


b.

Disconnect the B8 switch connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G30-24 (HSW) - B8-2 Below 1 Ω
B8-1 - Body ground Below 1 Ω
G30-24 (HSW) or B8-2 - Body ground 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR