Home › Vehicle Interior › THEFT DETERRENT › THEFT DETERRENT SYSTEM
RM24M0E _58 Vehicle Interior _059585 THEFT DETERRENT _0292193 THEFT DETERRENT SYSTEM J

THEFT DETERRENT  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is operating, the main body ECU outputs a signal continuously at 0.4 second intervals, causing the security horn to sound.


WIRING DIAGRAM

B128907E04
5.688,5.031 6.802,5.219 1.115,0.188 10 false Certification ECU 2.698,2.771 3.292,2.927 0.594,0.156 10 false S/HORN 1.25,1.885 1.844,2.042 0.594,0.156 10 false S/HORN 5.938,1.719 6.26,1.875 0.323,0.156 10 false SH- 4.448,5.479 4.99,6.021 0.542,0.542 10 false A12 0.771,3.833 1.677,3.99 0.906,0.156 10 false RH R/B BATT 0.781,4.667 1.479,4.865 0.698,0.198 10 false FL MAIN 0.865,5.604 1.563,5.802 0.698,0.198 10 false Battery 5.625,1.813 5.833,1.969 0.208,0.156 10 false 20 5.677,4.865 5.99,5.01 0.313,0.146 10 false G30 4.073,5.427 4.24,5.604 0.167,0.177 10 false 1 2.479,1.604 2.646,1.781 0.167,0.177 10 false 1 2.458,2.271 2.625,2.448 0.167,0.177 10 false 5 3.385,1.594 3.552,1.771 0.167,0.177 10 false 2 3.396,2.25 3.563,2.427 0.167,0.177 10 false 3 4.438,5.656 4.979,6.198 0.542,0.542 10 false Security Horn

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY HORN)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the security horn sounds.

Certification ECU:
Item Test Details Diagnostic Note
SECURITY HORN Security horn ON / OFF -

OK:

Security horn operates normally.




NG

2.INSPECT FUSE (S/HORN)

OK

REPLACE CERTIFICATION ECU

2.INSPECT FUSE (S/HORN)
a.

Remove the S/HORN fuse from the engine room No. 2 relay block.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

3.INSPECT SECURITY HORN RELAY (Marking: S/HORN)

NG

REPLACE FUSE

3.INSPECT SECURITY HORN RELAY (Marking: S/HORN)
a.

Remove the security horn relay from the engine room No. 2 relay block.


B426341E09
2.521,1.625 2.917,1.625 false 2,0.719 1.719,0.719 false 2.927,0.74 2.646,0.74 false 2.521,1.125 2.917,1.125 false 0.24,0.76 0.458,0.979 0.219,0.219 10 false 3 0.229,1.323 0.448,1.542 0.219,0.219 10 false 2 1.198,0.76 1.417,0.979 0.219,0.219 10 false 5 1.177,1.323 1.396,1.542 0.219,0.219 10 false 1 1.563,0.625 1.781,0.844 0.219,0.219 10 false 1 2.99,1.042 3.208,1.26 0.219,0.219 10 false 5 2.979,1.531 3.198,1.75 0.219,0.219 10 false 3 2.979,0.656 3.198,0.875 0.219,0.219 10 false 2

b.

Measure the resistance of the relay.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(Battery voltage applied to terminals 1 and 2)




OK

4.INSPECT SECURITY HORN ASSEMBLY

NG

REPLACE SECURITY HORN RELAY

4.INSPECT SECURITY HORN ASSEMBLY
B148512

a.

Remove the security horn.


b.

Check the operation of the horn.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Horn bracket
Horn sounds




OK

5.CHECK WIRE HARNESS (SECURITY HORN RELAY - SECURITY HORN)

NG

REPLACE SECURITY HORN RELAY

5.CHECK WIRE HARNESS (SECURITY HORN RELAY - SECURITY HORN)
B457203E01
4.667,1.417 5.083,1.667 0.417,0.25 0.104,0.083 1.771,0.427 1.667,0.344 10 false Wire Harness Side: 1.646,0.333 3.313,0.677 1.667,0.344 10 false Security Horn Relay 0.104,1.104 0.875,1.708 0.771,0.604 10 false Engine Room No. 2 Relay Block 4.75,1.458 5.51,1.76 0.76,0.302 10 false A12 5.198,0.979 6.865,1.323 1.667,0.344 10 false Security Horn

a.

Remove the security horn relay from the engine room No. 2 relay block.


b.

Disconnect the A12 horn connector.


c.

Measure the resistance of the relay block.

Standard resistance:
Tester Connection Specified Condition
Engine room No. 2 relay block security horn relay terminal 3 - A12-1 Below 1 Ω




OK

6.CHECK WIRE HARNESS (CERTIFICATION ECU - SECURITY HORN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (CERTIFICATION ECU - SECURITY HORN RELAY)
B457202E01
0.417,0.583 0.833,0.833 0.417,0.25 1.583,1.906 1.823,1.552 false 0.26,0.125 1.594,0.406 1.333,0.281 10 false Wire Harness Side: 1.323,0.604 2.531,0.885 1.208,0.281 10 false Certification ECU 0.479,0.625 1,0.875 0.521,0.25 10 false G30 1.406,1.927 1.927,2.177 0.521,0.25 10 false SH- 3.5,0.26 5.594,0.802 2.094,0.542 10 false Engine Room No. 2 Relay Block 5.823,1.281 6.708,1.698 0.885,0.417 10 false Security Horn Relay

a.

Disconnect the G30 ECU connector.


b.

Remove the security horn relay from the engine room No. 2 relay block.


c.

Measure the resistance of the wire harness side connectors and relay block.

Standard resistance:
Tester Connection Specified Condition
G30-20 (SH-) - Relay block security horn relay terminal 2 Below 1 Ω




OK

REPLACE CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR