Home › Vehicle Interior › THEFT DETERRENT › THEFT DETERRENT SYSTEM
RM24M0E _58 Vehicle Interior _059585 THEFT DETERRENT _0292193 THEFT DETERRENT SYSTEM D

THEFT DETERRENT  THEFT DETERRENT SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

The certification ECU controls the vehicle's theft deterrent system functions. Theft deterrent system data can be read through the data link connector 3 (DLC3) of the vehicle.

When the system seems to be malfunctioning, use the intelligent tester to check for malfunctions and perform repairs.



CHECK DLC3


H103023E07
1.708,1.875 1.948,1.469 true 1.563,0.917 1.208,0.438 true 1.76,0.927 1.542,0.448 true 1.948,0.927 2.031,0.448 true 2.135,0.927 2.427,0.458 true 2.458,1.896 2.313,1.479 true 1.031,0.25 1.281,0.427 0.25,0.177 10 false CG 1.427,1.906 1.896,2.094 0.469,0.188 10 false CANL 1.396,0.25 1.646,0.427 0.25,0.177 10 false SG 1.813,0.229 2.271,0.396 0.458,0.167 10 false CANH 2.417,0.229 2.677,0.406 0.26,0.177 10 false SIL 2.333,1.917 2.802,2.104 0.469,0.188 10 false BAT

B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

HINT:

The ECU uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.


Symbols (Terminal No.) Terminal Description Condition Specified Condition
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off* 54 to 69 Ω
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off* 200 Ω or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off* 200 Ω or higher
CANH (6) - BAT (16) HIGH-level CAN bus line Ignition switch off* 6 kΩ or higher
CANL (14) - BAT (16) LOW-level CAN bus line Ignition switch off* 6 kΩ or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.


If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

HINT:

Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.

If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.